arm64: dts: qcom: pm8150x: add thermal alarms and thermal zones

Add temperature alarm and thermal zone configuration to all three
pm8150 instances. Configuration is largely based on the msm-4.19 tree.
These alarms use main adc of the pmic. Separate temperature adc is not
supported yet.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200621192824.2069145-3-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arch/arm64/boot/dts/qcom/pm8150.dtsi

@@ -9,6 +9,37 @@
 #include <dt-bindings/spmi/spmi.h>
 #include <dt-bindings/iio/qcom,spmi-vadc.h>
 
+/ {
+	thermal-zones {
+		pm8150 {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8150_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pm8150_0: pmic@0 {
 		compatible = "qcom,pm8150", "qcom,spmi-pmic";
@@ -30,6 +61,15 @@ pwrkey {
 			};
 		};
 
+		pm8150_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
 		pm8150_adc: adc@3100 {
 			compatible = "qcom,spmi-adc5";
 			reg = <0x3100>;
@@ -38,8 +78,6 @@ pm8150_adc: adc@3100 {
 			#io-channel-cells = <1>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 
-			status = "disabled";
-
 			ref-gnd@0 {
 				reg = <ADC5_REF_GND>;
 				qcom,pre-scaling = <1 1>;

arch/arm64/boot/dts/qcom/pm8150b.dtsi

@@ -8,6 +8,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pm8150b {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8150b_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pmic@2 {
 		compatible = "qcom,pm8150b", "qcom,spmi-pmic";
@@ -22,7 +53,16 @@ power-on@800 {
 			status = "disabled";
 		};
 
-		adc@3100 {
+		pm8150b_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8150b_adc: adc@3100 {
 			compatible = "qcom,spmi-adc5";
 			reg = <0x3100>;
 			#address-cells = <1>;
@@ -30,8 +70,6 @@ adc@3100 {
 			#io-channel-cells = <1>;
 			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 
-			status = "disabled";
-
 			ref-gnd@0 {
 				reg = <ADC5_REF_GND>;
 				qcom,pre-scaling = <1 1>;

arch/arm64/boot/dts/qcom/pm8150l.dtsi

@@ -8,6 +8,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pm8150l {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8150l_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pmic@4 {
 		compatible = "qcom,pm8150l", "qcom,spmi-pmic";
@@ -22,7 +53,16 @@ power-on@800 {
 			status = "disabled";
 		};
 
-		adc@3100 {
+		pm8150l_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pm8150l_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8150l_adc: adc@3100 {
 			compatible = "qcom,spmi-adc5";
 			reg = <0x3100>;
 			#address-cells = <1>;
@@ -30,8 +70,6 @@ adc@3100 {
 			#io-channel-cells = <1>;
 			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 
-			status = "disabled";
-
 			ref-gnd@0 {
 				reg = <ADC5_REF_GND>;
 				qcom,pre-scaling = <1 1>;