Commit 4c8643b0 authored by Abhishek Sahu's avatar Abhishek Sahu Committed by Greg Kroah-Hartman

mtd: nand: qcom: fix read failure without complete bootchain

commit d8a9b320 upstream.

The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is

    0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID

The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Reviewed-by: default avatarArchit Taneja <architt@codeaurora.org>
Signed-off-by: default avatarAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: default avatarBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 020e0809
......@@ -109,7 +109,11 @@
#define READ_ADDR 0
/* NAND_DEV_CMD_VLD bits */
#define READ_START_VLD 0
#define READ_START_VLD BIT(0)
#define READ_STOP_VLD BIT(1)
#define WRITE_START_VLD BIT(2)
#define ERASE_START_VLD BIT(3)
#define SEQ_READ_START_VLD BIT(4)
/* NAND_EBI2_ECC_BUF_CFG bits */
#define NUM_STEPS 0
......@@ -148,6 +152,10 @@
#define FETCH_ID 0xb
#define RESET_DEVICE 0xd
/* Default Value for NAND_DEV_CMD_VLD */
#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \
ERASE_START_VLD | SEQ_READ_START_VLD)
/*
* the NAND controller performs reads/writes with ECC in 516 byte chunks.
* the driver calls the chunks 'step' or 'codeword' interchangeably
......@@ -672,8 +680,7 @@ static int nandc_param(struct qcom_nand_host *host)
/* configure CMD1 and VLD for ONFI param probing */
nandc_set_reg(nandc, NAND_DEV_CMD_VLD,
(nandc->vld & ~(1 << READ_START_VLD))
| 0 << READ_START_VLD);
(nandc->vld & ~READ_START_VLD));
nandc_set_reg(nandc, NAND_DEV_CMD1,
(nandc->cmd1 & ~(0xFF << READ_ADDR))
| NAND_CMD_PARAM << READ_ADDR);
......@@ -1972,13 +1979,14 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
{
/* kill onenand */
nandc_write(nandc, SFLASHC_BURST_CFG, 0);
nandc_write(nandc, NAND_DEV_CMD_VLD, NAND_DEV_CMD_VLD_VAL);
/* enable ADM DMA */
nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN);
/* save the original values of these registers */
nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1);
nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD);
nandc->vld = NAND_DEV_CMD_VLD_VAL;
return 0;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment