Commit 53e84b67 authored by David Brownell's avatar David Brownell Committed by Linus Torvalds

rtc: ds1305/ds1306 driver

Support the Dallas/Maxim DS1305 and DS1306 RTC chips.  These use SPI, and
support alarms, NVRAM, and a trickle charger for use when their backup
power supply is a supercap or rechargeable cell.

This basic driver doesn't yet support suspend/resume or wakealarms.
Signed-off-by: default avatarDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 8fc2c767
......@@ -282,6 +282,16 @@ config RTC_DRV_M41T94
This driver can also be built as a module. If so, the module
will be called rtc-m41t94.
config RTC_DRV_DS1305
tristate "Dallas/Maxim DS1305/DS1306"
help
Select this driver to get support for the Dallas/Maxim DS1305
and DS1306 real time clock chips. These support a trickle
charger, alarms, and NVRAM in addition to the clock.
This driver can also be built as a module. If so, the module
will be called rtc-ds1305.
config RTC_DRV_MAX6902
tristate "Maxim MAX6902"
help
......
......@@ -24,6 +24,7 @@ obj-$(CONFIG_RTC_DRV_BFIN) += rtc-bfin.o
obj-$(CONFIG_RTC_DRV_CMOS) += rtc-cmos.o
obj-$(CONFIG_RTC_DRV_DS1216) += rtc-ds1216.o
obj-$(CONFIG_RTC_DRV_DS1302) += rtc-ds1302.o
obj-$(CONFIG_RTC_DRV_DS1305) += rtc-ds1305.o
obj-$(CONFIG_RTC_DRV_DS1307) += rtc-ds1307.o
obj-$(CONFIG_RTC_DRV_DS1374) += rtc-ds1374.o
obj-$(CONFIG_RTC_DRV_DS1511) += rtc-ds1511.o
......
This diff is collapsed.
#ifndef __LINUX_SPI_DS1305_H
#define __LINUX_SPI_DS1305_H
/*
* One-time configuration for ds1305 and ds1306 RTC chips.
*
* Put a pointer to this in spi_board_info.platform_data if you want to
* be sure that Linux (re)initializes this as needed ... after losing
* backup power, and potentially on the first boot.
*/
struct ds1305_platform_data {
/* Trickle charge configuration: it's OK to leave out the MAGIC
* bitmask; mask in either DS1 or DS2, and then one of 2K/4k/8K.
*/
#define DS1305_TRICKLE_MAGIC 0xa0
#define DS1305_TRICKLE_DS2 0x08 /* two diodes */
#define DS1305_TRICKLE_DS1 0x04 /* one diode */
#define DS1305_TRICKLE_2K 0x01 /* 2 KOhm resistance */
#define DS1305_TRICKLE_4K 0x02 /* 4 KOhm resistance */
#define DS1305_TRICKLE_8K 0x03 /* 8 KOhm resistance */
u8 trickle;
/* set only on ds1306 parts */
bool is_ds1306;
/* ds1306 only: enable 1 Hz output */
bool en_1hz;
/* REVISIT: the driver currently expects nINT0 to be wired
* as the alarm IRQ. ALM1 may also need to be set up ...
*/
};
#endif /* __LINUX_SPI_DS1305_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment