Commit 54792dc2 authored by Sakthivel K's avatar Sakthivel K Committed by James Bottomley

[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone

Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: default avatarSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: default avatarAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: default avatarJack Wang <jack_wang@usish.com>
Reviewed-by: default avatarHannes Reinecke <hare@suse.de>
Signed-off-by: default avatarJames Bottomley <JBottomley@Parallels.com>
parent f5860992
......@@ -640,6 +640,18 @@ static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
static int pm8001_chip_init(struct pm8001_hba_info *pm8001_ha)
{
u8 i = 0;
u16 deviceid;
pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
/* 8081 controllers need BAR shift to access MPI space
* as this is shared with BIOS data */
if (deviceid == 0x8081) {
if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
GSM_SM_BASE));
return -1;
}
}
/* check the firmware status */
if (-1 == check_fw_ready(pm8001_ha)) {
PM8001_FAIL_DBG(pm8001_ha,
......@@ -660,9 +672,12 @@ static int pm8001_chip_init(struct pm8001_hba_info *pm8001_ha)
update_inbnd_queue_table(pm8001_ha, i);
for (i = 0; i < PM8001_MAX_OUTB_NUM; i++)
update_outbnd_queue_table(pm8001_ha, i);
mpi_set_phys_g3_with_ssc(pm8001_ha, 0);
/* 7->130ms, 34->500ms, 119->1.5s */
mpi_set_open_retry_interval_reg(pm8001_ha, 119);
/* 8081 controller donot require these operations */
if (deviceid != 0x8081) {
mpi_set_phys_g3_with_ssc(pm8001_ha, 0);
/* 7->130ms, 34->500ms, 119->1.5s */
mpi_set_open_retry_interval_reg(pm8001_ha, 119);
}
/* notify firmware update finished and check initialization status */
if (0 == mpi_init_check(pm8001_ha)) {
PM8001_INIT_DBG(pm8001_ha,
......@@ -684,6 +699,16 @@ static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
u16 deviceid;
pci_read_config_word(pm8001_ha->pdev, PCI_DEVICE_ID, &deviceid);
if (deviceid == 0x8081) {
if (-1 == pm8001_bar4_shift(pm8001_ha, GSM_SM_BASE)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Shift Bar4 to 0x%x failed\n",
GSM_SM_BASE));
return -1;
}
}
init_pci_device_addresses(pm8001_ha);
/* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
table is stop */
......
......@@ -131,6 +131,8 @@
#define LINKRATE_30 (0x02 << 8)
#define LINKRATE_60 (0x04 << 8)
/* for new SPC controllers MEMBASE III is shared between BIOS and DATA */
#define GSM_SM_BASE 0x4F0000
struct mpi_msg_hdr{
__le32 header; /* Bits [11:0] - Message operation code */
/* Bits [15:12] - Message Category */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment