Merge tag 'linux-watchdog-5.7-rc1' of git://www.linux-watchdog.org/linux-watchdog

Pull watchdog updates from Wim Van Sebroeck:

 - add TI K3 RTI watchdog

 - add stop_on_reboot parameter to control reboot policy

 - wm831x_wdt: Remove GPIO handling

 - several small fixes, improvements and clean-ups

* tag 'linux-watchdog-5.7-rc1' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: Add K3 RTI watchdog support
  dt-bindings: watchdog: Add support for TI K3 RTI watchdog
  watchdog: ziirave_wdt: change name to be more specific
  watchdog: orion: use 0 for unset heartbeat
  watchdog: npcm: remove whitespaces
  watchdog: reset last_hw_keepalive time at start
  watchdog: imx2_wdt: Drop .remove callback
  watchdog: Add stop_on_reboot parameter to control reboot policy
  watchdog: wm831x_wdt: Remove GPIO handling
  watchdog: imx7ulp: Remove unused include of init.h
  watchdog: imx_sc_wdt: Remove unused includes
  watchdog: qcom: Use irq flags from firmware
  watchdog: pm8916_wdt: Add system sleep callbacks
  watchdog: qcom-wdt: disable pretimeout on timer platform

Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/ti,rti-wdt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 SoC Watchdog Timer
+
+maintainers:
+  - Tero Kristo <t-kristo@ti.com>
+
+description:
+  The TI K3 SoC watchdog timer is implemented via the RTI (Real Time
+  Interrupt) IP module. This timer adds a support for windowed watchdog
+  mode, which will signal an error if it is pinged outside the watchdog
+  time window, meaning either too early or too late. The error signal
+  generated can be routed to either interrupt a safety controller or
+  to directly reset the SoC.
+
+allOf:
+  - $ref: "watchdog.yaml#"
+
+properties:
+  compatible:
+    enum:
+      - ti,j7-rti-wdt
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clocks-parents:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - power-domains
+
+examples:
+  - |
+    /*
+     * RTI WDT in main domain on J721e SoC. Assigned clocks are used to
+     * select the source clock for the watchdog, forcing it to tick with
+     * a 32kHz clock in this case.
+     */
+    #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+    watchdog0: rti@2200000 {
+        compatible = "ti,rti-wdt";
+        reg = <0x0 0x2200000 0x0 0x100>;
+        clocks = <&k3_clks 252 1>;
+        power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
+        assigned-clocks = <&k3_clks 252 1>;
+        assigned-clock-parents = <&k3_clks 252 5>;
+    };

drivers/watchdog/Kconfig

@@ -584,6 +584,14 @@ config DAVINCI_WATCHDOG
 	  NOTE: once enabled, this timer cannot be disabled.
 	  Say N if you are unsure.
 
+config K3_RTI_WATCHDOG
+	tristate "Texas Instruments K3 RTI watchdog"
+	depends on ARCH_K3 || COMPILE_TEST
+	select WATCHDOG_CORE
+	help
+	  Say Y here if you want to include support for the K3 watchdog
+	  timer (RTI module) available in the K3 generation of processors.
+
 config ORION_WATCHDOG
 	tristate "Orion watchdog"
 	depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU || (COMPILE_TEST && !ARCH_EBSA110)

drivers/watchdog/Makefile

@@ -57,6 +57,7 @@ obj-$(CONFIG_EP93XX_WATCHDOG) += ep93xx_wdt.o
 obj-$(CONFIG_PNX4008_WATCHDOG) += pnx4008_wdt.o
 obj-$(CONFIG_IOP_WATCHDOG) += iop_wdt.o
 obj-$(CONFIG_DAVINCI_WATCHDOG) += davinci_wdt.o
+obj-$(CONFIG_K3_RTI_WATCHDOG) += rti_wdt.o
 obj-$(CONFIG_ORION_WATCHDOG) += orion_wdt.o
 obj-$(CONFIG_SUNXI_WATCHDOG) += sunxi_wdt.o
 obj-$(CONFIG_RN5T618_WATCHDOG) += rn5t618_wdt.o

drivers/watchdog/imx2_wdt.c

@@ -244,6 +244,11 @@ static const struct regmap_config imx2_wdt_regmap_config = {
 	.max_register = 0x8,
 };
 
+static void imx2_wdt_action(void *data)
+{
+	clk_disable_unprepare(data);
+}
+
 static int __init imx2_wdt_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -292,6 +297,10 @@ static int __init imx2_wdt_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	ret = devm_add_action_or_reset(dev, imx2_wdt_action, wdev->clk);
+	if (ret)
+		return ret;
+
 	regmap_read(wdev->regmap, IMX2_WDT_WRSR, &val);
 	wdog->bootstatus = val & IMX2_WDT_WRSR_TOUT ? WDIOF_CARDRESET : 0;
 
@@ -315,32 +324,7 @@ static int __init imx2_wdt_probe(struct platform_device *pdev)
 	 */
 	regmap_write(wdev->regmap, IMX2_WDT_WMCR, 0);
 
-	ret = watchdog_register_device(wdog);
-	if (ret)
-		goto disable_clk;
-
-	dev_info(dev, "timeout %d sec (nowayout=%d)\n",
-		 wdog->timeout, nowayout);
-
-	return 0;
-
-disable_clk:
-	clk_disable_unprepare(wdev->clk);
-	return ret;
-}
-
-static int __exit imx2_wdt_remove(struct platform_device *pdev)
-{
-	struct watchdog_device *wdog = platform_get_drvdata(pdev);
-	struct imx2_wdt_device *wdev = watchdog_get_drvdata(wdog);
-
-	watchdog_unregister_device(wdog);
-
-	if (imx2_wdt_is_running(wdev)) {
-		imx2_wdt_ping(wdog);
-		dev_crit(&pdev->dev, "Device removed: Expect reboot!\n");
-	}
-	return 0;
+	return devm_watchdog_register_device(dev, wdog);
 }
 
 static void imx2_wdt_shutdown(struct platform_device *pdev)
@@ -417,7 +401,6 @@ static const struct of_device_id imx2_wdt_dt_ids[] = {
 MODULE_DEVICE_TABLE(of, imx2_wdt_dt_ids);
 
 static struct platform_driver imx2_wdt_driver = {
-	.remove		= __exit_p(imx2_wdt_remove),
 	.shutdown	= imx2_wdt_shutdown,
 	.driver		= {
 		.name	= DRIVER_NAME,

drivers/watchdog/imx7ulp_wdt.c

@@ -4,7 +4,6 @@
  */
 
 #include <linux/clk.h>
-#include <linux/init.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>

drivers/watchdog/imx_sc_wdt.c

@@ -6,13 +6,11 @@
 #include <linux/arm-smccc.h>
 #include <linux/firmware/imx/sci.h>
 #include <linux/io.h>
-#include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
-#include <linux/reboot.h>
 #include <linux/watchdog.h>
 
 #define DEFAULT_TIMEOUT 60

drivers/watchdog/npcm_wdt.c

@@ -103,30 +103,29 @@ static int npcm_wdt_stop(struct watchdog_device *wdd)
 	return 0;
 }
 
-
 static int npcm_wdt_set_timeout(struct watchdog_device *wdd,
 				unsigned int timeout)
 {
 	if (timeout < 2)
 		wdd->timeout = 1;
 	else if (timeout < 3)
-	      wdd->timeout = 2;
+		wdd->timeout = 2;
 	else if (timeout < 6)
-	      wdd->timeout = 5;
+		wdd->timeout = 5;
 	else if (timeout < 11)
-	      wdd->timeout = 10;
+		wdd->timeout = 10;
 	else if (timeout < 22)
-	      wdd->timeout = 21;
+		wdd->timeout = 21;
 	else if (timeout < 44)
-	      wdd->timeout = 43;
+		wdd->timeout = 43;
 	else if (timeout < 87)
-	      wdd->timeout = 86;
+		wdd->timeout = 86;
 	else if (timeout < 173)
-	      wdd->timeout = 172;
+		wdd->timeout = 172;
 	else if (timeout < 688)
-	      wdd->timeout = 687;
+		wdd->timeout = 687;
 	else
-	      wdd->timeout = 2750;
+		wdd->timeout = 2750;
 
 	if (watchdog_active(wdd))
 		npcm_wdt_start(wdd);

drivers/watchdog/orion_wdt.c

@@ -52,7 +52,7 @@
 #define WDT_A370_RATIO		(1 << WDT_A370_RATIO_SHIFT)
 
 static bool nowayout = WATCHDOG_NOWAYOUT;
-static int heartbeat = -1;		/* module parameter (seconds) */
+static int heartbeat;		/* module parameter (seconds) */
 
 struct orion_watchdog;
 

drivers/watchdog/pm8916_wdt.c

@@ -192,6 +192,7 @@ static int pm8916_wdt_probe(struct platform_device *pdev)
 	wdt->wdev.timeout = PM8916_WDT_DEFAULT_TIMEOUT;
 	wdt->wdev.pretimeout = 0;
 	watchdog_set_drvdata(&wdt->wdev, wdt);
+	platform_set_drvdata(pdev, wdt);
 
 	watchdog_init_timeout(&wdt->wdev, 0, dev);
 	pm8916_wdt_configure_timers(&wdt->wdev);
@@ -199,6 +200,29 @@ static int pm8916_wdt_probe(struct platform_device *pdev)
 	return devm_watchdog_register_device(dev, &wdt->wdev);
 }
 
+static int __maybe_unused pm8916_wdt_suspend(struct device *dev)
+{
+	struct pm8916_wdt *wdt = dev_get_drvdata(dev);
+
+	if (watchdog_active(&wdt->wdev))
+		return pm8916_wdt_stop(&wdt->wdev);
+
+	return 0;
+}
+
+static int __maybe_unused pm8916_wdt_resume(struct device *dev)
+{
+	struct pm8916_wdt *wdt = dev_get_drvdata(dev);
+
+	if (watchdog_active(&wdt->wdev))
+		return pm8916_wdt_start(&wdt->wdev);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(pm8916_wdt_pm_ops, pm8916_wdt_suspend,
+			 pm8916_wdt_resume);
+
 static const struct of_device_id pm8916_wdt_id_table[] = {
 	{ .compatible = "qcom,pm8916-wdt" },
 	{ }
@@ -210,6 +234,7 @@ static struct platform_driver pm8916_wdt_driver = {
 	.driver = {
 		.name = "pm8916-wdt",
 		.of_match_table = of_match_ptr(pm8916_wdt_id_table),
+		.pm = &pm8916_wdt_pm_ops,
 	},
 };
 module_platform_driver(pm8916_wdt_driver);

drivers/watchdog/qcom-wdt.c

@@ -40,6 +40,11 @@ static const u32 reg_offset_data_kpss[] = {
 	[WDT_BITE_TIME] = 0x14,
 };
 
+struct qcom_wdt_match_data {
+	const u32 *offset;
+	bool pretimeout;
+};
+
 struct qcom_wdt {
 	struct watchdog_device	wdd;
 	unsigned long		rate;
@@ -179,19 +184,29 @@ static void qcom_clk_disable_unprepare(void *data)
 	clk_disable_unprepare(data);
 }
 
+static const struct qcom_wdt_match_data match_data_apcs_tmr = {
+	.offset = reg_offset_data_apcs_tmr,
+	.pretimeout = false,
+};
+
+static const struct qcom_wdt_match_data match_data_kpss = {
+	.offset = reg_offset_data_kpss,
+	.pretimeout = true,
+};
+
 static int qcom_wdt_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct qcom_wdt *wdt;
 	struct resource *res;
 	struct device_node *np = dev->of_node;
-	const u32 *regs;
+	const struct qcom_wdt_match_data *data;
 	u32 percpu_offset;
 	int irq, ret;
 	struct clk *clk;
 
-	regs = of_device_get_match_data(dev);
-	if (!regs) {
+	data = of_device_get_match_data(dev);
+	if (!data) {
 		dev_err(dev, "Unsupported QCOM WDT module\n");
 		return -ENODEV;
 	}
@@ -247,9 +262,8 @@ static int qcom_wdt_probe(struct platform_device *pdev)
 
 	/* check if there is pretimeout support */
 	irq = platform_get_irq_optional(pdev, 0);
-	if (irq > 0) {
-		ret = devm_request_irq(dev, irq, qcom_wdt_isr,
-				       IRQF_TRIGGER_RISING,
+	if (data->pretimeout && irq > 0) {
+		ret = devm_request_irq(dev, irq, qcom_wdt_isr, 0,
 				       "wdt_bark", &wdt->wdd);
 		if (ret)
 			return ret;
@@ -267,7 +281,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
 	wdt->wdd.min_timeout = 1;
 	wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
 	wdt->wdd.parent = dev;
-	wdt->layout = regs;
+	wdt->layout = data->offset;
 
 	if (readl(wdt_addr(wdt, WDT_STS)) & 1)
 		wdt->wdd.bootstatus = WDIOF_CARDRESET;
@@ -311,9 +325,9 @@ static int __maybe_unused qcom_wdt_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(qcom_wdt_pm_ops, qcom_wdt_suspend, qcom_wdt_resume);
 
 static const struct of_device_id qcom_wdt_of_table[] = {
-	{ .compatible = "qcom,kpss-timer", .data = reg_offset_data_apcs_tmr },
-	{ .compatible = "qcom,scss-timer", .data = reg_offset_data_apcs_tmr },
-	{ .compatible = "qcom,kpss-wdt", .data = reg_offset_data_kpss },
+	{ .compatible = "qcom,kpss-timer", .data = &match_data_apcs_tmr },
+	{ .compatible = "qcom,scss-timer", .data = &match_data_apcs_tmr },
+	{ .compatible = "qcom,kpss-wdt", .data = &match_data_kpss },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, qcom_wdt_of_table);

drivers/watchdog/rti_wdt.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Watchdog driver for the K3 RTI module
+ *
+ * (c) Copyright 2019-2020 Texas Instruments Inc.
+ * All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+#include <linux/watchdog.h>
+
+#define DEFAULT_HEARTBEAT 60
+
+/* Max heartbeat is calculated at 32kHz source clock */
+#define MAX_HEARTBEAT	1000
+
+/* Timer register set definition */
+#define RTIDWDCTRL	0x90
+#define RTIDWDPRLD	0x94
+#define RTIWDSTATUS	0x98
+#define RTIWDKEY	0x9c
+#define RTIDWDCNTR	0xa0
+#define RTIWWDRXCTRL	0xa4
+#define RTIWWDSIZECTRL	0xa8
+
+#define RTIWWDRX_NMI	0xa
+
+#define RTIWWDSIZE_50P	0x50
+
+#define WDENABLE_KEY	0xa98559da
+
+#define WDKEY_SEQ0		0xe51a
+#define WDKEY_SEQ1		0xa35c
+
+#define WDT_PRELOAD_SHIFT	13
+
+#define WDT_PRELOAD_MAX		0xfff
+
+#define DWDST			BIT(1)
+
+static int heartbeat;
+
+/*
+ * struct to hold data for each WDT device
+ * @base - base io address of WD device
+ * @freq - source clock frequency of WDT
+ * @wdd  - hold watchdog device as is in WDT core
+ */
+struct rti_wdt_device {
+	void __iomem		*base;
+	unsigned long		freq;
+	struct watchdog_device	wdd;
+};
+
+static int rti_wdt_start(struct watchdog_device *wdd)
+{
+	u32 timer_margin;
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* set timeout period */
+	timer_margin = (u64)wdd->timeout * wdt->freq;
+	timer_margin >>= WDT_PRELOAD_SHIFT;
+	if (timer_margin > WDT_PRELOAD_MAX)
+		timer_margin = WDT_PRELOAD_MAX;
+	writel_relaxed(timer_margin, wdt->base + RTIDWDPRLD);
+
+	/*
+	 * RTI only supports a windowed mode, where the watchdog can only
+	 * be petted during the open window; not too early or not too late.
+	 * The HW configuration options only allow for the open window size
+	 * to be 50% or less than that; we obviouly want to configure the open
+	 * window as large as possible so we select the 50% option. To avoid
+	 * any glitches, we accommodate 5% safety margin also, so we setup
+	 * the min_hw_hearbeat at 55% of the timeout period.
+	 */
+	wdd->min_hw_heartbeat_ms = 11 * wdd->timeout * 1000 / 20;
+
+	/* Generate NMI when wdt expires */
+	writel_relaxed(RTIWWDRX_NMI, wdt->base + RTIWWDRXCTRL);
+
+	/* Open window size 50%; this is the largest window size available */
+	writel_relaxed(RTIWWDSIZE_50P, wdt->base + RTIWWDSIZECTRL);
+
+	readl_relaxed(wdt->base + RTIWWDSIZECTRL);
+
+	/* enable watchdog */
+	writel_relaxed(WDENABLE_KEY, wdt->base + RTIDWDCTRL);
+	return 0;
+}
+
+static int rti_wdt_ping(struct watchdog_device *wdd)
+{
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* put watchdog in service state */
+	writel_relaxed(WDKEY_SEQ0, wdt->base + RTIWDKEY);
+	/* put watchdog in active state */
+	writel_relaxed(WDKEY_SEQ1, wdt->base + RTIWDKEY);
+
+	return 0;
+}
+
+static unsigned int rti_wdt_get_timeleft(struct watchdog_device *wdd)
+{
+	u64 timer_counter;
+	u32 val;
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* if timeout has occurred then return 0 */
+	val = readl_relaxed(wdt->base + RTIWDSTATUS);
+	if (val & DWDST)
+		return 0;
+
+	timer_counter = readl_relaxed(wdt->base + RTIDWDCNTR);
+
+	do_div(timer_counter, wdt->freq);
+
+	return timer_counter;
+}
+
+static const struct watchdog_info rti_wdt_info = {
+	.options = WDIOF_KEEPALIVEPING,
+	.identity = "K3 RTI Watchdog",
+};
+
+static const struct watchdog_ops rti_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= rti_wdt_start,
+	.ping		= rti_wdt_ping,
+	.get_timeleft	= rti_wdt_get_timeleft,
+};
+
+static int rti_wdt_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct device *dev = &pdev->dev;
+	struct resource *wdt_mem;
+	struct watchdog_device *wdd;
+	struct rti_wdt_device *wdt;
+	struct clk *clk;
+
+	wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
+	if (!wdt)
+		return -ENOMEM;
+
+	clk = clk_get(dev, NULL);
+	if (IS_ERR(clk)) {
+		if (PTR_ERR(clk) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(clk);
+	}
+
+	wdt->freq = clk_get_rate(clk);
+
+	clk_put(clk);
+
+	if (!wdt->freq) {
+		dev_err(dev, "Failed to get fck rate.\n");
+		return -EINVAL;
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "runtime pm failed\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, wdt);
+
+	wdd = &wdt->wdd;
+	wdd->info = &rti_wdt_info;
+	wdd->ops = &rti_wdt_ops;
+	wdd->min_timeout = 1;
+	wdd->max_hw_heartbeat_ms = (WDT_PRELOAD_MAX << WDT_PRELOAD_SHIFT) /
+		wdt->freq * 1000;
+	wdd->timeout = DEFAULT_HEARTBEAT;
+	wdd->parent = dev;
+
+	watchdog_init_timeout(wdd, heartbeat, dev);
+
+	watchdog_set_drvdata(wdd, wdt);
+	watchdog_set_nowayout(wdd, 1);
+	watchdog_set_restart_priority(wdd, 128);
+
+	wdt_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	wdt->base = devm_ioremap_resource(dev, wdt_mem);
+	if (IS_ERR(wdt->base)) {
+		ret = PTR_ERR(wdt->base);
+		goto err_iomap;
+	}
+
+	ret = watchdog_register_device(wdd);
+	if (ret) {
+		dev_err(dev, "cannot register watchdog device\n");
+		goto err_iomap;
+	}
+
+	return 0;
+
+err_iomap:
+	pm_runtime_put_sync(&pdev->dev);
+
+	return ret;
+}
+
+static int rti_wdt_remove(struct platform_device *pdev)
+{
+	struct rti_wdt_device *wdt = platform_get_drvdata(pdev);
+
+	watchdog_unregister_device(&wdt->wdd);
+	pm_runtime_put(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id rti_wdt_of_match[] = {
+	{ .compatible = "ti,j7-rti-wdt", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rti_wdt_of_match);
+
+static struct platform_driver rti_wdt_driver = {
+	.driver = {
+		.name = "rti-wdt",
+		.of_match_table = rti_wdt_of_match,
+	},
+	.probe = rti_wdt_probe,
+	.remove = rti_wdt_remove,
+};
+
+module_platform_driver(rti_wdt_driver);
+
+MODULE_AUTHOR("Tero Kristo <t-kristo@ti.com>");
+MODULE_DESCRIPTION("K3 RTI Watchdog Driver");
+
+module_param(heartbeat, int, 0);
+MODULE_PARM_DESC(heartbeat,
+		 "Watchdog heartbeat period in seconds from 1 to "
+		 __MODULE_STRING(MAX_HEARTBEAT) ", default "
+		 __MODULE_STRING(DEFAULT_HEARTBEAT));
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:rti-wdt");

drivers/watchdog/watchdog_core.c

@@ -39,6 +39,10 @@
 
 static DEFINE_IDA(watchdog_ida);
 
+static int stop_on_reboot = -1;
+module_param(stop_on_reboot, int, 0444);
+MODULE_PARM_DESC(stop_on_reboot, "Stop watchdogs on reboot (0=keep watching, 1=stop)");
+
 /*
  * Deferred Registration infrastructure.
  *
@@ -254,6 +258,14 @@ static int __watchdog_register_device(struct watchdog_device *wdd)
 		}
 	}
 
+	/* Module parameter to force watchdog policy on reboot. */
+	if (stop_on_reboot != -1) {
+		if (stop_on_reboot)
+			set_bit(WDOG_STOP_ON_REBOOT, &wdd->status);
+		else
+			clear_bit(WDOG_STOP_ON_REBOOT, &wdd->status);
+	}
+
 	if (test_bit(WDOG_STOP_ON_REBOOT, &wdd->status)) {
 		wdd->reboot_nb.notifier_call = watchdog_reboot_notifier;
 

drivers/watchdog/watchdog_dev.c

@@ -282,6 +282,7 @@ static int watchdog_start(struct watchdog_device *wdd)
 	if (err == 0) {
 		set_bit(WDOG_ACTIVE, &wdd->status);
 		wd_data->last_keepalive = started_at;
+		wd_data->last_hw_keepalive = started_at;
 		watchdog_update_worker(wdd);
 	}
 

drivers/watchdog/wm831x_wdt.c

@@ -13,7 +13,6 @@
 #include <linux/platform_device.h>
 #include <linux/watchdog.h>
 #include <linux/uaccess.h>
-#include <linux/gpio.h>
 
 #include <linux/mfd/wm831x/core.h>
 #include <linux/mfd/wm831x/pdata.h>
@@ -29,7 +28,6 @@ struct wm831x_wdt_drvdata {
 	struct watchdog_device wdt;
 	struct wm831x *wm831x;
 	struct mutex lock;
-	int update_gpio;
 	int update_state;
 };
 
@@ -103,14 +101,6 @@ static int wm831x_wdt_ping(struct watchdog_device *wdt_dev)
 
 	mutex_lock(&driver_data->lock);
 
-	if (driver_data->update_gpio) {
-		gpio_set_value_cansleep(driver_data->update_gpio,
-					driver_data->update_state);
-		driver_data->update_state = !driver_data->update_state;
-		ret = 0;
-		goto out;
-	}
-
 	reg = wm831x_reg_read(wm831x, WM831X_WATCHDOG);
 
 	if (!(reg & WM831X_WDOG_RST_SRC)) {
@@ -239,23 +229,6 @@ static int wm831x_wdt_probe(struct platform_device *pdev)
 		reg |= pdata->secondary << WM831X_WDOG_SECACT_SHIFT;
 		reg |= pdata->software << WM831X_WDOG_RST_SRC_SHIFT;
 
-		if (pdata->update_gpio) {
-			ret = devm_gpio_request_one(dev, pdata->update_gpio,
-						    GPIOF_OUT_INIT_LOW,
-						    "Watchdog update");
-			if (ret < 0) {
-				dev_err(wm831x->dev,
-					"Failed to request update GPIO: %d\n",
-					ret);
-				return ret;
-			}
-
-			driver_data->update_gpio = pdata->update_gpio;
-
-			/* Make sure the watchdog takes hardware updates */
-			reg |= WM831X_WDOG_RST_SRC;
-		}
-
 		ret = wm831x_reg_unlock(wm831x);
 		if (ret == 0) {
 			ret = wm831x_reg_write(wm831x, WM831X_WATCHDOG, reg);

drivers/watchdog/ziirave_wdt.c

@@ -422,7 +422,7 @@ static int ziirave_firm_upload(struct watchdog_device *wdd,
 
 static const struct watchdog_info ziirave_wdt_info = {
 	.options = WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING,
-	.identity = "Zodiac RAVE Watchdog",
+	.identity = "RAVE Switch Watchdog",
 };
 
 static const struct watchdog_ops ziirave_wdt_ops = {

include/linux/mfd/wm831x/pdata.h

@@ -89,7 +89,6 @@ enum wm831x_watchdog_action {
 
 struct wm831x_watchdog_pdata {
 	enum wm831x_watchdog_action primary, secondary;
-	int update_gpio;
 	unsigned int software:1;
 };