Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:
 "A first round of pinctrl fixes for v3.8:
   - i.MX5 register configuration
   - Swap a kfree to devm_kfree() to avoid memory corruption in the at91
     driver
   - Add the missing device tree binding doc for the SIRF pin controller
   - Enable the SIRF GPIO pull up/down configuration from the device
     tree, it was previously retired from the hard-coded approach.
   - NULL check for the prcm_base in the Nomadik pin controller.
   - Provide the prcm_base from the device tree in the DT boot path for
     the Nomadik pin controller."

* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  ARM: ux500: add pinctrl address resources
  pinctrl: nomadik: return if prcm_base is NULL
  pinctrl: sirf: enable GPIO pullup/down configuration from dts
  pinctrl: sirf: add missing DT-binding document
  pinctrl: fix comment mistake
  drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
  pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration

Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt

+CSR SiRFprimaII pinmux controller
+
+Required properties:
+- compatible	: "sirf,prima2-pinctrl"
+- reg		: Address range of the pinctrl registers
+- interrupts    : Interrupts used by every GPIO group
+- gpio-controller : Indicates this device is a GPIO controller
+- interrupt-controller  : Marks the device node as an interrupt controller
+Optional properties:
+- sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m
+- sirf,pulldowns : if n-th bit of m-th bank is set, set a pulldown on GPIO-n of bank m
+
+Please refer to pinctrl-bindings.txt in this directory for details of the common
+pinctrl bindings used by client devices.
+
+SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes.
+Each of these subnodes represents some desired configuration for a group of pins.
+
+Required subnode-properties:
+- sirf,pins : An array of strings. Each string contains the name of a group.
+- sirf,function: A string containing the name of the function to mux to the
+  group.
+
+  Valid values for group and function names can be found from looking at the
+  group and function arrays in driver files:
+  drivers/pinctrl/pinctrl-sirf.c
+
+For example, pinctrl might have subnodes like the following:
+ uart2_pins_a: uart2@0 {
+         uart {
+                 sirf,pins = "uart2grp";
+                 sirf,function = "uart2";
+         };
+ };
+ uart2_noflow_pins_a: uart2@1 {
+         uart {
+                 sirf,pins = "uart2_nostreamctrlgrp";
+                 sirf,function = "uart2_nostreamctrl";
+         };
+ };
+
+For a specific board, if it wants to use uart2 without hardware flow control,
+it can add the following to its board-specific .dts file.
+uart2: uart@0xb0070000 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_noflow_pins_a>;
+}

arch/arm/boot/dts/dbx5x0.dtsi

@@ -170,7 +170,9 @@ gpio8: gpio@a03fe000 {
 			gpio-bank = <8>;
 		};
 
-		pinctrl {
+		pinctrl@80157000 {
+			// This is actually the PRCMU base address
+			reg = <0x80157000 0x2000>;
 			compatible = "stericsson,nmk_pinctrl";
 		};
 

arch/arm/mach-ux500/cpu-db8500.c

@@ -285,7 +285,8 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL),
 	OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
 	/* Requires device name bindings. */
-	OF_DEV_AUXDATA("stericsson,nmk_pinctrl", 0, "pinctrl-db8500", NULL),
+	OF_DEV_AUXDATA("stericsson,nmk_pinctrl", U8500_PRCMU_BASE,
+		"pinctrl-db8500", NULL),
 	/* Requires clock name and DMA bindings. */
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
 		"ux500-msp-i2s.0", &msp0_platform_data),

drivers/pinctrl/core.c

@@ -700,7 +700,7 @@ static struct pinctrl *create_pinctrl(struct device *dev)
 		}
 	}
 
-	/* Add the pinmux to the global list */
+	/* Add the pinctrl handle to the global list */
 	list_add_tail(&p->node, &pinctrl_list);
 
 	return p;

drivers/pinctrl/pinctrl-at91.c

@@ -265,7 +265,7 @@ static int at91_dt_node_to_map(struct pinctrl_dev *pctldev,
 	/* create mux map */
 	parent = of_get_parent(np);
 	if (!parent) {
-		kfree(new_map);
+		devm_kfree(pctldev->dev, new_map);
 		return -EINVAL;
 	}
 	new_map[0].type = PIN_MAP_TYPE_MUX_GROUP;

drivers/pinctrl/pinctrl-imx53.c

@@ -1371,7 +1371,7 @@ static struct imx_pin_reg imx53_pin_regs[] = {
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 0, 0x7F8, 1), /* MX53_PAD_GPIO_8__ESAI1_TX5_RX0 */
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 1, 0x000, 0), /* MX53_PAD_GPIO_8__GPIO1_8 */
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 2, 0x000, 0), /* MX53_PAD_GPIO_8__EPIT2_EPITO */
-	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 3, 0x760, 3), /* MX53_PAD_GPIO_8__CAN1_RXCAN */
+	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 3, 0x760, 2), /* MX53_PAD_GPIO_8__CAN1_RXCAN */
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 4, 0x880, 5), /* MX53_PAD_GPIO_8__UART2_RXD_MUX */
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 5, 0x000, 0), /* MX53_PAD_GPIO_8__FIRI_TXD */
 	IMX_PIN_REG(MX53_PAD_GPIO_8, 0x6C8, 0x338, 6, 0x000, 0), /* MX53_PAD_GPIO_8__SPDIF_SRCLK */

drivers/pinctrl/pinctrl-nomadik.c

@@ -259,6 +259,9 @@ static void nmk_prcm_altcx_set_mode(struct nmk_pinctrl *npct,
 	const struct prcm_gpiocr_altcx_pin_desc *pin_desc;
 	const u16 *gpiocr_regs;
 
+	if (!npct->prcm_base)
+		return;
+
 	if (alt_num > PRCM_IDX_GPIOCR_ALTC_MAX) {
 		dev_err(npct->dev, "PRCM GPIOCR: alternate-C%i is invalid\n",
 			alt_num);
@@ -682,6 +685,9 @@ static int nmk_prcm_gpiocr_get_mode(struct pinctrl_dev *pctldev, int gpio)
 	const struct prcm_gpiocr_altcx_pin_desc *pin_desc;
 	const u16 *gpiocr_regs;
 
+	if (!npct->prcm_base)
+		return NMK_GPIO_ALT_C;
+
 	for (i = 0; i < npct->soc->npins_altcx; i++) {
 		if (npct->soc->altcx_pins[i].pin == gpio)
 			break;
@@ -1887,9 +1893,12 @@ static int __devinit nmk_pinctrl_probe(struct platform_device *pdev)
 				"failed to ioremap PRCM registers\n");
 			return -ENOMEM;
 		}
-	} else {
+	} else if (version == PINCTRL_NMK_STN8815) {
 		dev_info(&pdev->dev,
 			 "No PRCM base, assume no ALT-Cx control is available\n");
+	} else {
+		dev_err(&pdev->dev, "missing PRCM base address\n");
+		return -EINVAL;
 	}
 
 	/*

drivers/pinctrl/pinctrl-sirf.c

@@ -1663,6 +1663,44 @@ const struct irq_domain_ops sirfsoc_gpio_irq_simple_ops = {
 	.xlate = irq_domain_xlate_twocell,
 };
 
+static void sirfsoc_gpio_set_pullup(const u32 *pullups)
+{
+	int i, n;
+	const unsigned long *p = (const unsigned long *)pullups;
+
+	for (i = 0; i < SIRFSOC_GPIO_NO_OF_BANKS; i++) {
+		n = find_first_bit(p + i, BITS_PER_LONG);
+		while (n < BITS_PER_LONG) {
+			u32 offset = SIRFSOC_GPIO_CTRL(i, n);
+			u32 val = readl(sgpio_bank[i].chip.regs + offset);
+			val |= SIRFSOC_GPIO_CTL_PULL_MASK;
+			val |= SIRFSOC_GPIO_CTL_PULL_HIGH;
+			writel(val, sgpio_bank[i].chip.regs + offset);
+
+			n = find_next_bit(p + i, BITS_PER_LONG, n + 1);
+		}
+	}
+}
+
+static void sirfsoc_gpio_set_pulldown(const u32 *pulldowns)
+{
+	int i, n;
+	const unsigned long *p = (const unsigned long *)pulldowns;
+
+	for (i = 0; i < SIRFSOC_GPIO_NO_OF_BANKS; i++) {
+		n = find_first_bit(p + i, BITS_PER_LONG);
+		while (n < BITS_PER_LONG) {
+			u32 offset = SIRFSOC_GPIO_CTRL(i, n);
+			u32 val = readl(sgpio_bank[i].chip.regs + offset);
+			val |= SIRFSOC_GPIO_CTL_PULL_MASK;
+			val &= ~SIRFSOC_GPIO_CTL_PULL_HIGH;
+			writel(val, sgpio_bank[i].chip.regs + offset);
+
+			n = find_next_bit(p + i, BITS_PER_LONG, n + 1);
+		}
+	}
+}
+
 static int __devinit sirfsoc_gpio_probe(struct device_node *np)
 {
 	int i, err = 0;
@@ -1671,6 +1709,8 @@ static int __devinit sirfsoc_gpio_probe(struct device_node *np)
 	struct platform_device *pdev;
 	bool is_marco = false;
 
+	u32 pullups[SIRFSOC_GPIO_NO_OF_BANKS], pulldowns[SIRFSOC_GPIO_NO_OF_BANKS];
+
 	pdev = of_find_device_by_node(np);
 	if (!pdev)
 		return -ENODEV;
@@ -1726,6 +1766,14 @@ static int __devinit sirfsoc_gpio_probe(struct device_node *np)
 		irq_set_handler_data(bank->parent_irq, bank);
 	}
 
+	if (!of_property_read_u32_array(np, "sirf,pullups", pullups,
+		SIRFSOC_GPIO_NO_OF_BANKS))
+		sirfsoc_gpio_set_pullup(pullups);
+
+	if (!of_property_read_u32_array(np, "sirf,pulldowns", pulldowns,
+		SIRFSOC_GPIO_NO_OF_BANKS))
+		sirfsoc_gpio_set_pulldown(pulldowns);
+
 	return 0;
 
 out: