Commit 62810e5a authored by Daniel Vetter's avatar Daniel Vetter

drm/i915: enable intel_lvds->pre_pll_enable for ilk+, too

Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg
Reviewed-by: default avatarPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
parent fc683091
......@@ -5322,7 +5322,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
bool ok, has_reduced_clock = false;
bool is_lvds = false, is_dp = false, is_cpu_edp = false;
struct intel_encoder *encoder;
u32 temp;
int ret;
bool dither, fdi_config_ok;
......@@ -5386,45 +5385,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
} else
intel_put_pch_pll(intel_crtc);
/* The LVDS pin pair needs to be on before the DPLLs are enabled.
* This is an exception to the general rule that mode_set doesn't turn
* things on.
*/
if (is_lvds) {
temp = I915_READ(PCH_LVDS);
temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
if (HAS_PCH_CPT(dev)) {
temp &= ~PORT_TRANS_SEL_MASK;
temp |= PORT_TRANS_SEL_CPT(pipe);
} else {
if (pipe == 1)
temp |= LVDS_PIPEB_SELECT;
else
temp &= ~LVDS_PIPEB_SELECT;
}
/* set the corresponsding LVDS_BORDER bit */
temp |= dev_priv->lvds_border_bits;
/* Set the B0-B3 data pairs corresponding to whether we're going to
* set the DPLLs for dual-channel mode or not.
*/
if (clock.p2 == 7)
temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
else
temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
/* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
* appropriately here, but we need to look more thoroughly into how
* panels behave in the two modes.
*/
temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
temp |= LVDS_HSYNC_POLARITY;
if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
temp |= LVDS_VSYNC_POLARITY;
I915_WRITE(PCH_LVDS, temp);
}
if (is_dp && !is_cpu_edp) {
intel_dp_set_m_n(crtc, mode, adjusted_mode);
} else {
......
......@@ -104,17 +104,20 @@ static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
int pipe = intel_crtc->pipe;
u32 temp;
/* pch split platforms are not yet converted. */
if (HAS_PCH_SPLIT(dev))
return;
temp = I915_READ(lvds_encoder->reg);
temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
if (pipe == 1) {
temp |= LVDS_PIPEB_SELECT;
if (HAS_PCH_CPT(dev)) {
temp &= ~PORT_TRANS_SEL_MASK;
temp |= PORT_TRANS_SEL_CPT(pipe);
} else {
temp &= ~LVDS_PIPEB_SELECT;
if (pipe == 1) {
temp |= LVDS_PIPEB_SELECT;
} else {
temp &= ~LVDS_PIPEB_SELECT;
}
}
/* set the corresponsding LVDS_BORDER bit */
temp |= dev_priv->lvds_border_bits;
/* Set the B0-B3 data pairs corresponding to whether we're going to
......@@ -129,8 +132,11 @@ static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
* appropriately here, but we need to look more thoroughly into how
* panels behave in the two modes.
*/
/* set the dithering flag on LVDS as needed */
if (INTEL_INFO(dev)->gen >= 4) {
/* Set the dithering flag on LVDS as needed, note that there is no
* special lvds dither control bit on pch-split platforms, dithering is
* only controlled through the PIPECONF reg. */
if (INTEL_INFO(dev)->gen == 4) {
if (dev_priv->lvds_dither)
temp |= LVDS_ENABLE_DITHER;
else
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment