igb: No longer rely on APME to determine WoL settings

Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/igb/igb.h

@@ -370,8 +370,6 @@ struct igb_adapter {
 	u32 eims_other;
 
 	/* to not mess up cache alignment, always add to the bottom */
-	u32 eeprom_wol;
-
 	u16 tx_ring_count;
 	u16 rx_ring_count;
 	unsigned int vfs_allocated_count;
@@ -401,6 +399,7 @@ struct igb_adapter {
 #define IGB_FLAG_PTP			(1 << 5)
 #define IGB_FLAG_RSS_FIELD_IPV4_UDP	(1 << 6)
 #define IGB_FLAG_RSS_FIELD_IPV6_UDP	(1 << 7)
+#define IGB_FLAG_WOL_SUPPORTED		(1 << 8)
 
 /* DMA Coalescing defines */
 #define IGB_MIN_TXPBSIZE           20408

drivers/net/ethernet/intel/igb/igb_ethtool.c

@@ -1966,54 +1966,6 @@ static void igb_diag_test(struct net_device *netdev,
 	msleep_interruptible(4 * 1000);
 }
 
-static int igb_wol_exclusion(struct igb_adapter *adapter,
-			     struct ethtool_wolinfo *wol)
-{
-	struct e1000_hw *hw = &adapter->hw;
-	int retval = 1; /* fail by default */
-
-	switch (hw->device_id) {
-	case E1000_DEV_ID_82575GB_QUAD_COPPER:
-		/* WoL not supported */
-		wol->supported = 0;
-		break;
-	case E1000_DEV_ID_82575EB_FIBER_SERDES:
-	case E1000_DEV_ID_82576_FIBER:
-	case E1000_DEV_ID_82576_SERDES:
-		/* Wake events not supported on port B */
-		if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) {
-			wol->supported = 0;
-			break;
-		}
-		/* return success for non excluded adapter ports */
-		retval = 0;
-		break;
-	case E1000_DEV_ID_82576_QUAD_COPPER:
-	case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
-		/* quad port adapters only support WoL on port A */
-		if (!(adapter->flags & IGB_FLAG_QUAD_PORT_A)) {
-			wol->supported = 0;
-			break;
-		}
-		/* return success for non excluded adapter ports */
-		retval = 0;
-		break;
-	default:
-		/* dual port cards only support WoL on port A from now on
-		 * unless it was enabled in the eeprom for port B
-		 * so exclude FUNC_1 ports from having WoL enabled */
-		if ((rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) &&
-		    !adapter->eeprom_wol) {
-			wol->supported = 0;
-			break;
-		}
-
-		retval = 0;
-	}
-
-	return retval;
-}
-
 static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 {
 	struct igb_adapter *adapter = netdev_priv(netdev);
@@ -2023,10 +1975,7 @@ static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 	                 WAKE_PHY;
 	wol->wolopts = 0;
 
-	/* this function will set ->supported = 0 and return 1 if wol is not
-	 * supported by this hardware */
-	if (igb_wol_exclusion(adapter, wol) ||
-	    !device_can_wakeup(&adapter->pdev->dev))
+	if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
 		return;
 
 	/* apply any specific unsupported masks here */
@@ -2054,8 +2003,7 @@ static int igb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 	if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE))
 		return -EOPNOTSUPP;
 
-	if (igb_wol_exclusion(adapter, wol) ||
-	    !device_can_wakeup(&adapter->pdev->dev))
+	if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
 		return wol->wolopts ? -EOPNOTSUPP : 0;
 
 	/* these settings will always override what we currently have */

drivers/net/ethernet/intel/igb/igb_main.c

@@ -1837,7 +1837,6 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 	const struct e1000_info *ei = igb_info_tbl[ent->driver_data];
 	unsigned long mmio_start, mmio_len;
 	int err, pci_using_dac;
-	u16 eeprom_apme_mask = IGB_EEPROM_APME;
 	u8 part_str[E1000_PBANUM_LENGTH];
 
 	/* Catch broken hardware that put the wrong VF device ID in
@@ -2045,28 +2044,27 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 
 	igb_validate_mdi_setting(hw);
 
-	/* Initial Wake on LAN setting If APM wake is enabled in the EEPROM,
-	 * enable the ACPI Magic Packet filter
-	 */
-
+	/* By default, support wake on port A */
 	if (hw->bus.func == 0)
-		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
-	else if (hw->mac.type >= e1000_82580)
+		adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
+
+	/* Check the NVM for wake support on non-port A ports */
+	if (hw->mac.type >= e1000_82580)
 		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
 		                 NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
 		                 &eeprom_data);
 	else if (hw->bus.func == 1)
 		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
 
-	if (eeprom_data & eeprom_apme_mask)
-		adapter->eeprom_wol |= E1000_WUFC_MAG;
+	if (eeprom_data & IGB_EEPROM_APME)
+		adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
 
 	/* now that we have the eeprom settings, apply the special cases where
 	 * the eeprom may be wrong or the board simply won't support wake on
 	 * lan on a particular port */
 	switch (pdev->device) {
 	case E1000_DEV_ID_82575GB_QUAD_COPPER:
-		adapter->eeprom_wol = 0;
+		adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
 		break;
 	case E1000_DEV_ID_82575EB_FIBER_SERDES:
 	case E1000_DEV_ID_82576_FIBER:
@@ -2074,24 +2072,38 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 		/* Wake events only supported on port A for dual fiber
 		 * regardless of eeprom setting */
 		if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1)
-			adapter->eeprom_wol = 0;
+			adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
 		break;
 	case E1000_DEV_ID_82576_QUAD_COPPER:
 	case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
 		/* if quad port adapter, disable WoL on all but port A */
 		if (global_quad_port_a != 0)
-			adapter->eeprom_wol = 0;
+			adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
 		else
 			adapter->flags |= IGB_FLAG_QUAD_PORT_A;
 		/* Reset for multiple quad port adapters */
 		if (++global_quad_port_a == 4)
 			global_quad_port_a = 0;
 		break;
+	default:
+		/* If the device can't wake, don't set software support */
+		if (!device_can_wakeup(&adapter->pdev->dev))
+			adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
 	}
 
 	/* initialize the wol settings based on the eeprom settings */
-	adapter->wol = adapter->eeprom_wol;
-	device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+	if (adapter->flags & IGB_FLAG_WOL_SUPPORTED)
+		adapter->wol |= E1000_WUFC_MAG;
+
+	/* Some vendors want WoL disabled by default, but still supported */
+	if ((hw->mac.type == e1000_i350) &&
+	    (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)) {
+		adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
+		adapter->wol = 0;
+	}
+
+	device_set_wakeup_enable(&adapter->pdev->dev,
+				 adapter->flags & IGB_FLAG_WOL_SUPPORTED);
 
 	/* reset the hardware with the new settings */
 	igb_reset(adapter);