Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, including a couple of newly added
  drivers:

   - The Qualcomm external bus interface 2 (EBI2), used in some of their
     mobile phone chips for connecting flash memory, LCD displays or
     other peripherals

   - Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
     the EFUSE based on that firmware interface.

   - Perf support for the AppliedMicro X-Gene performance monitor unit

   - Reset driver for STMicroelectronics STM32

   - Reset driver for SocioNext UniPhier SoCs

  Aside from these, there are minor updates to SoC-specific bus,
  clocksource, firmware, pinctrl, reset, rtc and pmic drivers"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  bus: qcom-ebi2: depend on HAS_IOMEM
  pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
  clk: mvebu: Add clk support for the orion5x SoC mv88f5181
  dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
  clocksource: exynos_mct: Add the support for ARM64
  perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
  Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
  MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
  bus: qcom: add EBI2 driver
  bus: qcom: add EBI2 device tree bindings
  rtc: rtc-pm8xxx: Add support for pm8018 rtc
  nvmem: amlogic: Add Amlogic Meson EFUSE driver
  firmware: Amlogic: Add secure monitor driver
  soc: qcom: smd: Reset rx tail rather than tx
  memory: atmel-sdramc: fix a possible NULL dereference
  reset: hi6220: allow to compile test driver on other architectures
  reset: zynq: add driver Kconfig option
  reset: sunxi: add driver Kconfig option
  reset: stm32: add driver Kconfig option
  reset: socfpga: add driver Kconfig option
  ...

Documentation/devicetree/bindings/arm/samsung/pmu.txt

@@ -10,6 +10,7 @@ Properties:
 		   - "samsung,exynos5260-pmu" - for Exynos5260 SoC.
 		   - "samsung,exynos5410-pmu" - for Exynos5410 SoC,
 		   - "samsung,exynos5420-pmu" - for Exynos5420 SoC.
+		   - "samsung,exynos5433-pmu" - for Exynos5433 SoC.
 		   - "samsung,exynos7-pmu" - for Exynos7 SoC.
 		second value must be always "syscon".
 

Documentation/devicetree/bindings/bus/qcom,ebi2.txt

+Qualcomm External Bus Interface 2 (EBI2)
+
+The EBI2 contains two peripheral blocks: XMEM and LCDC. The XMEM handles any
+external memory (such as NAND or other memory-mapped peripherals) whereas
+LCDC handles LCD displays.
+
+As it says it connects devices to an external bus interface, meaning address
+lines (up to 9 address lines so can only address 1KiB external memory space),
+data lines (16 bits), OE (output enable), ADV (address valid, used on some
+NOR flash memories), WE (write enable). This on top of 6 different chip selects
+(CS0 thru CS5) so that in theory 6 different devices can be connected.
+
+Apparently this bus is clocked at 64MHz. It has dedicated pins on the package
+and the bus can only come out on these pins, however if some of the pins are
+unused they can be left unconnected or remuxed to be used as GPIO or in some
+cases other orthogonal functions as well.
+
+Also CS1 and CS2 has -A and -B signals. Why they have that is unclear to me.
+
+The chip selects have the following memory range assignments. This region of
+memory is referred to as "Chip Peripheral SS FPB0" and is 168MB big.
+
+Chip Select                     Physical address base
+CS0 GPIO134                     0x1a800000-0x1b000000 (8MB)
+CS1 GPIO39 (A) / GPIO123 (B)    0x1b000000-0x1b800000 (8MB)
+CS2 GPIO40 (A) / GPIO124 (B)    0x1b800000-0x1c000000 (8MB)
+CS3 GPIO133                     0x1d000000-0x25000000 (128 MB)
+CS4 GPIO132                     0x1c800000-0x1d000000 (8MB)
+CS5 GPIO131                     0x1c000000-0x1c800000 (8MB)
+
+The APQ8060 Qualcomm Application Processor User Guide, 80-N7150-14 Rev. A,
+August 6, 2012 contains some incomplete documentation of the EBI2.
+
+FIXME: the manual mentions "write precharge cycles" and "precharge cycles".
+We have not been able to figure out which bit fields these correspond to
+in the hardware, or what valid values exist. The current hypothesis is that
+this is something just used on the FAST chip selects and that the SLOW
+chip selects are understood fully. There is also a "byte device enable"
+flag somewhere for 8bit memories.
+
+FIXME: The chipselects have SLOW and FAST configuration registers. It's a bit
+unclear what this means, if they are mutually exclusive or can be used
+together, or if some chip selects are hardwired to be FAST and others are SLOW
+by design.
+
+The XMEM registers are totally undocumented but could be partially decoded
+because the Cypress AN49576 Antioch Westbridge apparently has suspiciously
+similar register layout, see: http://www.cypress.com/file/105771/download
+
+Required properties:
+- compatible: should be one of:
+  "qcom,msm8660-ebi2"
+  "qcom,apq8060-ebi2"
+- #address-cells: shoule be <2>: the first cell is the chipselect,
+  the second cell is the offset inside the memory range
+- #size-cells: should be <1>
+- ranges: should be set to:
+  ranges = <0 0x0 0x1a800000 0x00800000>,
+           <1 0x0 0x1b000000 0x00800000>,
+           <2 0x0 0x1b800000 0x00800000>,
+           <3 0x0 0x1d000000 0x08000000>,
+           <4 0x0 0x1c800000 0x00800000>,
+           <5 0x0 0x1c000000 0x00800000>;
+- reg: two ranges of registers: EBI2 config and XMEM config areas
+- reg-names: should be "ebi2", "xmem"
+- clocks: two clocks, EBI_2X and EBI
+- clock-names: shoule be "ebi2x", "ebi2"
+
+Optional subnodes:
+- Nodes inside the EBI2 will be considered device nodes.
+
+The following optional properties are properties that can be tagged onto
+any device subnode. We are assuming that there can be only ONE device per
+chipselect subnode, else the properties will become ambigous.
+
+Optional properties arrays for SLOW chip selects:
+- qcom,xmem-recovery-cycles: recovery cycles is the time the memory continues to
+  drive the data bus after OE is de-asserted, in order to avoid contention on
+  the data bus. They are inserted when reading one CS and switching to another
+  CS or read followed by write on the same CS. Valid values 0 thru 15. Minimum
+  value is actually 1, so a value of 0 will still yield 1 recovery cycle.
+- qcom,xmem-write-hold-cycles: write hold cycles, these are extra cycles
+  inserted after every write minimum 1. The data out is driven from the time
+  WE is asserted until CS is asserted. With a hold of 1 (value = 0), the CS
+  stays active for 1 extra cycle etc. Valid values 0 thru 15.
+- qcom,xmem-write-delta-cycles: initial latency for write cycles inserted for
+  the first write to a page or burst memory. Valid values 0 thru 255.
+- qcom,xmem-read-delta-cycles: initial latency for read cycles inserted for the
+  first read to a page or burst memory. Valid values 0 thru 255.
+- qcom,xmem-write-wait-cycles: number of wait cycles for every write access, 0=1
+  cycle. Valid values 0 thru 15.
+- qcom,xmem-read-wait-cycles: number of wait cycles for every read access, 0=1
+  cycle. Valid values 0 thru 15.
+
+Optional properties arrays for FAST chip selects:
+- qcom,xmem-address-hold-enable: this is a boolean property stating that we
+  shall hold the address for an extra cycle to meet hold time requirements
+  with ADV assertion.
+- qcom,xmem-adv-to-oe-recovery-cycles: the number of cycles elapsed before an OE
+  assertion, with respect to the cycle where ADV (address valid) is asserted.
+  2 means 2 cycles between ADV and OE. Valid values 0, 1, 2 or 3.
+- qcom,xmem-read-hold-cycles: the length in cycles of the first segment of a
+  read transfer. For a single read trandfer this will be the time from CS
+  assertion to OE assertion. Valid values 0 thru 15.
+
+
+Example:
+
+ebi2@1a100000 {
+	compatible = "qcom,apq8060-ebi2";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0x0 0x1a800000 0x00800000>,
+		 <1 0x0 0x1b000000 0x00800000>,
+		 <2 0x0 0x1b800000 0x00800000>,
+		 <3 0x0 0x1d000000 0x08000000>,
+		 <4 0x0 0x1c800000 0x00800000>,
+		 <5 0x0 0x1c000000 0x00800000>;
+	reg = <0x1a100000 0x1000>, <0x1a110000 0x1000>;
+	reg-names = "ebi2", "xmem";
+	clocks = <&gcc EBI2_2X_CLK>, <&gcc EBI2_CLK>;
+	clock-names = "ebi2x", "ebi2";
+	/* Make sure to set up the pin control for the EBI2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&foo_ebi2_pins>;
+
+	foo-ebi2@2,0 {
+		compatible = "foo";
+		reg = <2 0x0 0x100>;
+		(...)
+		qcom,xmem-recovery-cycles = <0>;
+		qcom,xmem-write-hold-cycles = <3>;
+		qcom,xmem-write-delta-cycles = <31>;
+		qcom,xmem-read-delta-cycles = <28>;
+		qcom,xmem-write-wait-cycles = <9>;
+		qcom,xmem-read-wait-cycles = <9>;
+	};
+};

Documentation/devicetree/bindings/clock/mvebu-core-clock.txt

@@ -52,6 +52,7 @@ Required properties:
 	"marvell,dove-core-clock" - for Dove SoC core clocks
 	"marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180)
 	"marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC
+	"marvell,mv88f5181-core-clock" - for Orion MV88F5181 SoC
 	"marvell,mv88f5182-core-clock" - for Orion MV88F5182 SoC
 	"marvell,mv88f5281-core-clock" - for Orion MV88F5281 SoC
 	"marvell,mv88f6183-core-clock" - for Orion MV88F6183 SoC

Documentation/devicetree/bindings/clock/st,stm32-rcc.txt

 STMicroelectronics STM32 Reset and Clock Controller
 ===================================================
 
-The RCC IP is both a reset and a clock controller. This documentation only
-describes the clock part.
+The RCC IP is both a reset and a clock controller.
 
-Please also refer to clock-bindings.txt in this directory for common clock
-controller binding usage.
+Please refer to clock-bindings.txt for common clock controller binding usage.
+Please also refer to reset.txt for common reset controller binding usage.
 
 Required properties:
 - compatible: Should be "st,stm32f42xx-rcc"
 - reg: should be register base and length as documented in the
   datasheet
+- #reset-cells: 1, see below
 - #clock-cells: 2, device nodes should specify the clock in their "clocks"
   property, containing a phandle to the clock device node, an index selecting
   between gated clocks and other clocks and an index specifying the clock to
@@ -19,6 +19,7 @@ Required properties:
 Example:
 
 	rcc: rcc@40023800 {
+		#reset-cells = <1>;
 		#clock-cells = <2>
 		compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
 		reg = <0x40023800 0x400>;
@@ -35,16 +36,23 @@ from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
 It is calculated as: index = register_offset / 4 * 32 + bit_offset.
 Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
 
+To simplify the usage and to share bit definition with the reset and clock
+drivers of the RCC IP, macros are available to generate the index in
+human-readble format.
+
+For STM32F4 series, the macro are available here:
+ - include/dt-bindings/mfd/stm32f4-rcc.h
+
 Example:
 
 	/* Gated clock, AHB1 bit 0 (GPIOA) */
 	... {
-		clocks = <&rcc 0 0>
+		clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
 	};
 
 	/* Gated clock, AHB2 bit 4 (CRYP) */
 	... {
-		clocks = <&rcc 0 36>
+		clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
 	};
 
 Specifying other clocks
@@ -61,5 +69,25 @@ Example:
 
 	/* Misc clock, FCLK */
 	... {
-		clocks = <&rcc 1 1>
+		clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
+	};
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the reset device node and an index specifying
+which channel to use.
+The index is the bit number within the RCC registers bank, starting from RCC
+base address.
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register.
+For example, for CRC reset:
+  crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
+
+example:
+
+	timer2 {
+		resets	= <&rcc STM32F4_APB1_RESET(TIM2)>;
 	};

Documentation/devicetree/bindings/perf/apm-xgene-pmu.txt

+* APM X-Gene SoC PMU bindings
+
+This is APM X-Gene SoC PMU (Performance Monitoring Unit) module.
+The following PMU devices are supported:
+
+  L3C			- L3 cache controller
+  IOB			- IO bridge
+  MCB			- Memory controller bridge
+  MC			- Memory controller
+
+The following section describes the SoC PMU DT node binding.
+
+Required properties:
+- compatible		: Shall be "apm,xgene-pmu" for revision 1 or
+                          "apm,xgene-pmu-v2" for revision 2.
+- regmap-csw		: Regmap of the CPU switch fabric (CSW) resource.
+- regmap-mcba		: Regmap of the MCB-A (memory bridge) resource.
+- regmap-mcbb		: Regmap of the MCB-B (memory bridge) resource.
+- reg			: First resource shall be the CPU bus PMU resource.
+- interrupts            : Interrupt-specifier for PMU IRQ.
+
+Required properties for L3C subnode:
+- compatible		: Shall be "apm,xgene-pmu-l3c".
+- reg			: First resource shall be the L3C PMU resource.
+
+Required properties for IOB subnode:
+- compatible		: Shall be "apm,xgene-pmu-iob".
+- reg			: First resource shall be the IOB PMU resource.
+
+Required properties for MCB subnode:
+- compatible		: Shall be "apm,xgene-pmu-mcb".
+- reg			: First resource shall be the MCB PMU resource.
+- enable-bit-index	: The bit indicates if the according MCB is enabled.
+
+Required properties for MC subnode:
+- compatible		: Shall be "apm,xgene-pmu-mc".
+- reg			: First resource shall be the MC PMU resource.
+- enable-bit-index	: The bit indicates if the according MC is enabled.
+
+Example:
+	csw: csw@7e200000 {
+		compatible = "apm,xgene-csw", "syscon";
+		reg = <0x0 0x7e200000 0x0 0x1000>;
+	};
+
+	mcba: mcba@7e700000 {
+		compatible = "apm,xgene-mcb", "syscon";
+		reg = <0x0 0x7e700000 0x0 0x1000>;
+	};
+
+	mcbb: mcbb@7e720000 {
+		compatible = "apm,xgene-mcb", "syscon";
+		reg = <0x0 0x7e720000 0x0 0x1000>;
+	};
+
+	pmu: pmu@78810000 {
+		compatible = "apm,xgene-pmu-v2";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		regmap-csw = <&csw>;
+		regmap-mcba = <&mcba>;
+		regmap-mcbb = <&mcbb>;
+		reg = <0x0 0x78810000 0x0 0x1000>;
+		interrupts = <0x0 0x22 0x4>;
+
+		pmul3c@7e610000 {
+			compatible = "apm,xgene-pmu-l3c";
+			reg = <0x0 0x7e610000 0x0 0x1000>;
+		};
+
+		pmuiob@7e940000 {
+			compatible = "apm,xgene-pmu-iob";
+			reg = <0x0 0x7e940000 0x0 0x1000>;
+		};
+
+		pmucmcb@7e710000 {
+			compatible = "apm,xgene-pmu-mcb";
+			reg = <0x0 0x7e710000 0x0 0x1000>;
+			enable-bit-index = <0>;
+		};
+
+		pmucmcb@7e730000 {
+			compatible = "apm,xgene-pmu-mcb";
+			reg = <0x0 0x7e730000 0x0 0x1000>;
+			enable-bit-index = <1>;
+		};
+
+		pmucmc@7e810000 {
+			compatible = "apm,xgene-pmu-mc";
+			reg = <0x0 0x7e810000 0x0 0x1000>;
+			enable-bit-index = <0>;
+		};
+
+		pmucmc@7e850000 {
+			compatible = "apm,xgene-pmu-mc";
+			reg = <0x0 0x7e850000 0x0 0x1000>;
+			enable-bit-index = <1>;
+		};
+
+		pmucmc@7e890000 {
+			compatible = "apm,xgene-pmu-mc";
+			reg = <0x0 0x7e890000 0x0 0x1000>;
+			enable-bit-index = <2>;
+		};
+
+		pmucmc@7e8d0000 {
+			compatible = "apm,xgene-pmu-mc";
+			reg = <0x0 0x7e8d0000 0x0 0x1000>;
+			enable-bit-index = <3>;
+		};
+	};

Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt

@@ -4,7 +4,9 @@ Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
 part and usage.
 
 Required properties:
-- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl",
+- compatible: "marvell,88f5181-pinctrl",
+              "marvell,88f5181l-pinctrl",
+              "marvell,88f5182-pinctrl",
               "marvell,88f5281-pinctrl"
 
 - reg: two register areas, the first one describing the first two

Documentation/devicetree/bindings/reset/st,stm32-rcc.txt

+STMicroelectronics STM32 Peripheral Reset Controller
+====================================================
+
+The RCC IP is both a reset and a clock controller.
+
+Please see Documentation/devicetree/bindings/clock/st,stm32-rcc.txt

Documentation/devicetree/bindings/reset/uniphier-reset.txt

+UniPhier reset controller
+
+
+System reset
+------------
+
+Required properties:
+- compatible: should be one of the following:
+    "socionext,uniphier-sld3-reset" - for PH1-sLD3 SoC.
+    "socionext,uniphier-ld4-reset"  - for PH1-LD4 SoC.
+    "socionext,uniphier-pro4-reset" - for PH1-Pro4 SoC.
+    "socionext,uniphier-sld8-reset" - for PH1-sLD8 SoC.
+    "socionext,uniphier-pro5-reset" - for PH1-Pro5 SoC.
+    "socionext,uniphier-pxs2-reset" - for ProXstream2/PH1-LD6b SoC.
+    "socionext,uniphier-ld11-reset" - for PH1-LD11 SoC.
+    "socionext,uniphier-ld20-reset" - for PH1-LD20 SoC.
+- #reset-cells: should be 1.
+
+Example:
+
+	sysctrl@61840000 {
+		compatible = "socionext,uniphier-ld20-sysctrl",
+			     "simple-mfd", "syscon";
+		reg = <0x61840000 0x4000>;
+
+		reset {
+			compatible = "socionext,uniphier-ld20-reset";
+			#reset-cells = <1>;
+		};
+
+		other nodes ...
+	};
+
+
+Media I/O (MIO) reset
+---------------------
+
+Required properties:
+- compatible: should be one of the following:
+    "socionext,uniphier-sld3-mio-reset" - for PH1-sLD3 SoC.
+    "socionext,uniphier-ld4-mio-reset"  - for PH1-LD4 SoC.
+    "socionext,uniphier-pro4-mio-reset" - for PH1-Pro4 SoC.
+    "socionext,uniphier-sld8-mio-reset" - for PH1-sLD8 SoC.
+    "socionext,uniphier-pro5-mio-reset" - for PH1-Pro5 SoC.
+    "socionext,uniphier-pxs2-mio-reset" - for ProXstream2/PH1-LD6b SoC.
+    "socionext,uniphier-ld11-mio-reset" - for PH1-LD11 SoC.
+    "socionext,uniphier-ld20-mio-reset" - for PH1-LD20 SoC.
+- #reset-cells: should be 1.
+
+Example:
+
+	mioctrl@59810000 {
+		compatible = "socionext,uniphier-ld20-mioctrl",
+			     "simple-mfd", "syscon";
+		reg = <0x59810000 0x800>;
+
+		reset {
+			compatible = "socionext,uniphier-ld20-mio-reset";
+			#reset-cells = <1>;
+		};
+
+		other nodes ...
+	};
+
+
+Peripheral reset
+----------------
+
+Required properties:
+- compatible: should be one of the following:
+    "socionext,uniphier-ld4-peri-reset"  - for PH1-LD4 SoC.
+    "socionext,uniphier-pro4-peri-reset" - for PH1-Pro4 SoC.
+    "socionext,uniphier-sld8-peri-reset" - for PH1-sLD8 SoC.
+    "socionext,uniphier-pro5-peri-reset" - for PH1-Pro5 SoC.
+    "socionext,uniphier-pxs2-peri-reset" - for ProXstream2/PH1-LD6b SoC.
+    "socionext,uniphier-ld11-peri-reset" - for PH1-LD11 SoC.
+    "socionext,uniphier-ld20-peri-reset" - for PH1-LD20 SoC.
+- #reset-cells: should be 1.
+
+Example:
+
+	perictrl@59820000 {
+		compatible = "socionext,uniphier-ld20-perictrl",
+			     "simple-mfd", "syscon";
+		reg = <0x59820000 0x200>;
+
+		reset {
+			compatible = "socionext,uniphier-ld20-peri-reset";
+			#reset-cells = <1>;
+		};
+
+		other nodes ...
+	};

Documentation/perf/xgene-pmu.txt

+APM X-Gene SoC Performance Monitoring Unit (PMU)
+================================================
+
+X-Gene SoC PMU consists of various independent system device PMUs such as
+L3 cache(s), I/O bridge(s), memory controller bridge(s) and memory
+controller(s). These PMU devices are loosely architected to follow the
+same model as the PMU for ARM cores. The PMUs share the same top level
+interrupt and status CSR region.
+
+PMU (perf) driver
+-----------------
+
+The xgene-pmu driver registers several perf PMU drivers. Each of the perf
+driver provides description of its available events and configuration options
+in sysfs, see /sys/devices/<l3cX/iobX/mcbX/mcX>/.
+
+The "format" directory describes format of the config (event ID),
+config1 (agent ID) fields of the perf_event_attr structure. The "events"
+directory provides configuration templates for all supported event types that
+can be used with perf tool. For example, "l3c0/bank-fifo-full/" is an
+equivalent of "l3c0/config=0x0b/".
+
+Most of the SoC PMU has a specific list of agent ID used for monitoring
+performance of a specific datapath. For example, agents of a L3 cache can be
+a specific CPU or an I/O bridge. Each PMU has a set of 2 registers capable of
+masking the agents from which the request come from. If the bit with
+the bit number corresponding to the agent is set, the event is counted only if
+it is caused by a request from that agent. Each agent ID bit is inversely mapped
+to a corresponding bit in "config1" field. By default, the event will be
+counted for all agent requests (config1 = 0x0). For all the supported agents of
+each PMU, please refer to APM X-Gene User Manual.
+
+Each perf driver also provides a "cpumask" sysfs attribute, which contains a
+single CPU ID of the processor which will be used to handle all the PMU events.
+
+Example for perf tool use:
+
+ / # perf list | grep -e l3c -e iob -e mcb -e mc
+   l3c0/ackq-full/                                    [Kernel PMU event]
+ <...>
+   mcb1/mcb-csw-stall/                                [Kernel PMU event]
+
+ / # perf stat -a -e l3c0/read-miss/,mcb1/csw-write-request/ sleep 1
+
+ / # perf stat -a -e l3c0/read-miss,config1=0xfffffffffffffffe/ sleep 1
+
+The driver does not support sampling, therefore "perf record" will
+not work. Per-task (without "-a") perf sessions are not supported.

MAINTAINERS

@@ -866,6 +866,13 @@ F:	drivers/net/phy/mdio-xgene.c
 F:	Documentation/devicetree/bindings/net/apm-xgene-enet.txt
 F:	Documentation/devicetree/bindings/net/apm-xgene-mdio.txt
 
+APPLIED MICRO (APM) X-GENE SOC PMU
+M:	Tai Nguyen <ttnguyen@apm.com>
+S:	Supported
+F:	drivers/perf/xgene_pmu.c
+F:	Documentation/perf/xgene-pmu.txt
+F:	Documentation/devicetree/bindings/perf/apm-xgene-pmu.txt
+
 APTINA CAMERA SENSOR PLL
 M:	Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
 L:	linux-media@vger.kernel.org
@@ -1861,6 +1868,7 @@ F:	drivers/bus/uniphier-system-bus.c
 F:	drivers/clk/uniphier/
 F:	drivers/i2c/busses/i2c-uniphier*
 F:	drivers/pinctrl/uniphier/
+F:	drivers/reset/reset-uniphier.c
 F:	drivers/tty/serial/8250/8250_uniphier.c
 N:	uniphier
 

arch/arm/boot/dts/stm32f429.dtsi

@@ -334,6 +334,7 @@ pins {
 		};
 
 		rcc: rcc@40023810 {
+			#reset-cells = <1>;
 			#clock-cells = <2>;
 			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
 			reg = <0x40023800 0x400>;

drivers/bus/Kconfig

@@ -108,6 +108,14 @@ config OMAP_OCP2SCP
 	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
 	  OCP2SCP.
 
+config QCOM_EBI2
+	bool "Qualcomm External Bus Interface 2 (EBI2)"
+	depends on HAS_IOMEM
+	help
+	  Say y here to enable support for the Qualcomm External Bus
+	  Interface 2, which can be used to connect things like NAND Flash,
+	  SRAM, ethernet adapters, FPGAs and LCD displays.
+
 config SIMPLE_PM_BUS
 	bool "Simple Power-Managed Bus Driver"
 	depends on OF && PM
@@ -132,12 +140,8 @@ config SUNXI_RSB
 	  with various RSB based devices, such as AXP223, AXP8XX PMICs,
 	  and AC100/AC200 ICs.
 
-# TODO: This uses pm_clk_*() symbols that aren't exported in v4.7 and hence
-# the driver will fail to build as a module. However there are patches to
-# address that queued for v4.8, so this can be turned into a tristate symbol
-# after v4.8-rc1.
 config TEGRA_ACONNECT
-	bool "Tegra ACONNECT Bus Driver"
+	tristate "Tegra ACONNECT Bus Driver"
 	depends on ARCH_TEGRA_210_SOC
 	depends on OF && PM
 	select PM_CLK

drivers/bus/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_MVEBU_MBUS) 	+= mvebu-mbus.o
 obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
+obj-$(CONFIG_QCOM_EBI2)		+= qcom-ebi2.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_SIMPLE_PM_BUS)	+= simple-pm-bus.o
 obj-$(CONFIG_TEGRA_ACONNECT)	+= tegra-aconnect.o

drivers/bus/tegra-aconnect.c

@@ -15,24 +15,6 @@
 #include <linux/pm_clock.h>
 #include <linux/pm_runtime.h>
 
-static int tegra_aconnect_add_clock(struct device *dev, char *name)
-{
-	struct clk *clk;
-	int ret;
-
-	clk = clk_get(dev, name);
-	if (IS_ERR(clk)) {
-		dev_err(dev, "%s clock not found\n", name);
-		return PTR_ERR(clk);
-	}
-
-	ret = pm_clk_add_clk(dev, clk);
-	if (ret)
-		clk_put(clk);
-
-	return ret;
-}
-
 static int tegra_aconnect_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -44,11 +26,11 @@ static int tegra_aconnect_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = tegra_aconnect_add_clock(&pdev->dev, "ape");
+	ret = of_pm_clk_add_clk(&pdev->dev, "ape");
 	if (ret)
 		goto clk_destroy;
 
-	ret = tegra_aconnect_add_clock(&pdev->dev, "apb2ape");
+	ret = of_pm_clk_add_clk(&pdev->dev, "apb2ape");
 	if (ret)
 		goto clk_destroy;
 

drivers/clk/mvebu/orion.c

@@ -20,6 +20,76 @@ static const struct coreclk_ratio orion_coreclk_ratios[] __initconst = {
 	{ .id = 0, .name = "ddrclk", }
 };
 
+/*
+ * Orion 5181
+ */
+
+#define SAR_MV88F5181_TCLK_FREQ      8
+#define SAR_MV88F5181_TCLK_FREQ_MASK 0x3
+
+static u32 __init mv88f5181_get_tclk_freq(void __iomem *sar)
+{
+	u32 opt = (readl(sar) >> SAR_MV88F5181_TCLK_FREQ) &
+		SAR_MV88F5181_TCLK_FREQ_MASK;
+	if (opt == 0)
+		return 133333333;
+	else if (opt == 1)
+		return 150000000;
+	else if (opt == 2)
+		return 166666667;
+	else
+		return 0;
+}
+
+#define SAR_MV88F5181_CPU_FREQ       4
+#define SAR_MV88F5181_CPU_FREQ_MASK  0xf
+
+static u32 __init mv88f5181_get_cpu_freq(void __iomem *sar)
+{
+	u32 opt = (readl(sar) >> SAR_MV88F5181_CPU_FREQ) &
+		SAR_MV88F5181_CPU_FREQ_MASK;
+	if (opt == 0)
+		return 333333333;
+	else if (opt == 1 || opt == 2)
+		return 400000000;
+	else if (opt == 3)
+		return 500000000;
+	else
+		return 0;
+}
+
+static void __init mv88f5181_get_clk_ratio(void __iomem *sar, int id,
+					   int *mult, int *div)
+{
+	u32 opt = (readl(sar) >> SAR_MV88F5181_CPU_FREQ) &
+		SAR_MV88F5181_CPU_FREQ_MASK;
+	if (opt == 0 || opt == 1) {
+		*mult = 1;
+		*div  = 2;
+	} else if (opt == 2 || opt == 3) {
+		*mult = 1;
+		*div  = 3;
+	} else {
+		*mult = 0;
+		*div  = 1;
+	}
+}
+
+static const struct coreclk_soc_desc mv88f5181_coreclks = {
+	.get_tclk_freq = mv88f5181_get_tclk_freq,
+	.get_cpu_freq = mv88f5181_get_cpu_freq,
+	.get_clk_ratio = mv88f5181_get_clk_ratio,
+	.ratios = orion_coreclk_ratios,
+	.num_ratios = ARRAY_SIZE(orion_coreclk_ratios),
+};
+
+static void __init mv88f5181_clk_init(struct device_node *np)
+{
+	return mvebu_coreclk_setup(np, &mv88f5181_coreclks);
+}
+
+CLK_OF_DECLARE(mv88f5181_clk, "marvell,mv88f5181-core-clock", mv88f5181_clk_init);
+
 /*
  * Orion 5182
  */

drivers/clocksource/Kconfig

@@ -361,7 +361,7 @@ config CLKSRC_METAG_GENERIC
 
 config CLKSRC_EXYNOS_MCT
 	bool "Exynos multi core timer driver" if COMPILE_TEST
-	depends on ARM
+	depends on ARM || ARM64
 	help
 	  Support for Multi Core Timer controller on Exynos SoCs.
 

drivers/clocksource/exynos_mct.c

@@ -223,6 +223,7 @@ static u64 notrace exynos4_read_sched_clock(void)
 	return exynos4_read_count_32();
 }
 
+#if defined(CONFIG_ARM)
 static struct delay_timer exynos4_delay_timer;
 
 static cycles_t exynos4_read_current_timer(void)
@@ -231,14 +232,17 @@ static cycles_t exynos4_read_current_timer(void)
 			 "cycles_t needs to move to 32-bit for ARM64 usage");
 	return exynos4_read_count_32();
 }
+#endif
 
 static int __init exynos4_clocksource_init(void)
 {
 	exynos4_mct_frc_start();
 
+#if defined(CONFIG_ARM)
 	exynos4_delay_timer.read_current_timer = &exynos4_read_current_timer;
 	exynos4_delay_timer.freq = clk_rate;
 	register_current_timer_delay(&exynos4_delay_timer);
+#endif
 
 	if (clocksource_register_hz(&mct_frc, clk_rate))
 		panic("%s: can't register clocksource\n", mct_frc.name);

drivers/firmware/Kconfig

@@ -209,5 +209,6 @@ config HAVE_ARM_SMCCC
 source "drivers/firmware/broadcom/Kconfig"
 source "drivers/firmware/google/Kconfig"
 source "drivers/firmware/efi/Kconfig"
+source "drivers/firmware/meson/Kconfig"
 
 endmenu

drivers/firmware/Makefile

@@ -22,6 +22,7 @@ obj-$(CONFIG_QCOM_SCM_32)	+= qcom_scm-32.o
 CFLAGS_qcom_scm-32.o :=$(call as-instr,.arch armv7-a\n.arch_extension sec,-DREQUIRES_SEC=1) -march=armv7-a
 
 obj-y				+= broadcom/
+obj-y				+= meson/
 obj-$(CONFIG_GOOGLE_FIRMWARE)	+= google/
 obj-$(CONFIG_EFI)		+= efi/
 obj-$(CONFIG_UEFI_CPER)		+= efi/

drivers/firmware/meson/Kconfig

+#
+# Amlogic Secure Monitor driver
+#
+config MESON_SM
+	bool
+	default ARCH_MESON
+	depends on ARM64_4K_PAGES
+	help
+	  Say y here to enable the Amlogic secure monitor driver

drivers/firmware/meson/Makefile

+obj-$(CONFIG_MESON_SM) +=	meson_sm.o

drivers/firmware/meson/meson_sm.c

+/*
+ * Amlogic Secure Monitor driver
+ *
+ * Copyright (C) 2016 Endless Mobile, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#define pr_fmt(fmt) "meson-sm: " fmt
+
+#include <linux/arm-smccc.h>
+#include <linux/bug.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/printk.h>
+#include <linux/types.h>
+#include <linux/sizes.h>
+
+#include <linux/firmware/meson/meson_sm.h>
+
+struct meson_sm_cmd {
+	unsigned int index;
+	u32 smc_id;
+};
+#define CMD(d, s) { .index = (d), .smc_id = (s), }
+
+struct meson_sm_chip {
+	unsigned int shmem_size;
+	u32 cmd_shmem_in_base;
+	u32 cmd_shmem_out_base;
+	struct meson_sm_cmd cmd[];
+};
+
+struct meson_sm_chip gxbb_chip = {
+	.shmem_size		= SZ_4K,
+	.cmd_shmem_in_base	= 0x82000020,
+	.cmd_shmem_out_base	= 0x82000021,
+	.cmd = {
+		CMD(SM_EFUSE_READ,	0x82000030),
+		CMD(SM_EFUSE_WRITE,	0x82000031),
+		CMD(SM_EFUSE_USER_MAX,	0x82000033),
+		{ /* sentinel */ },
+	},
+};
+
+struct meson_sm_firmware {
+	const struct meson_sm_chip *chip;
+	void __iomem *sm_shmem_in_base;
+	void __iomem *sm_shmem_out_base;
+};
+
+static struct meson_sm_firmware fw;
+
+static u32 meson_sm_get_cmd(const struct meson_sm_chip *chip,
+			    unsigned int cmd_index)
+{
+	const struct meson_sm_cmd *cmd = chip->cmd;
+
+	while (cmd->smc_id && cmd->index != cmd_index)
+		cmd++;
+
+	return cmd->smc_id;
+}
+
+static u32 __meson_sm_call(u32 cmd, u32 arg0, u32 arg1, u32 arg2,
+			   u32 arg3, u32 arg4)
+{
+	struct arm_smccc_res res;
+
+	arm_smccc_smc(cmd, arg0, arg1, arg2, arg3, arg4, 0, 0, &res);
+	return res.a0;
+}
+
+static void __iomem *meson_sm_map_shmem(u32 cmd_shmem, unsigned int size)
+{
+	u32 sm_phy_base;
+
+	sm_phy_base = __meson_sm_call(cmd_shmem, 0, 0, 0, 0, 0);
+	if (!sm_phy_base)
+		return 0;
+
+	return ioremap_cache(sm_phy_base, size);
+}
+
+/**
+ * meson_sm_call - generic SMC32 call to the secure-monitor
+ *
+ * @cmd_index:	Index of the SMC32 function ID
+ * @ret:	Returned value
+ * @arg0:	SMC32 Argument 0
+ * @arg1:	SMC32 Argument 1
+ * @arg2:	SMC32 Argument 2
+ * @arg3:	SMC32 Argument 3
+ * @arg4:	SMC32 Argument 4
+ *
+ * Return:	0 on success, a negative value on error
+ */
+int meson_sm_call(unsigned int cmd_index, u32 *ret, u32 arg0,
+		  u32 arg1, u32 arg2, u32 arg3, u32 arg4)
+{
+	u32 cmd, lret;
+
+	if (!fw.chip)
+		return -ENOENT;
+
+	cmd = meson_sm_get_cmd(fw.chip, cmd_index);
+	if (!cmd)
+		return -EINVAL;
+
+	lret = __meson_sm_call(cmd, arg0, arg1, arg2, arg3, arg4);
+
+	if (ret)
+		*ret = lret;
+
+	return 0;
+}
+EXPORT_SYMBOL(meson_sm_call);
+
+/**
+ * meson_sm_call_read - retrieve data from secure-monitor
+ *
+ * @buffer:	Buffer to store the retrieved data
+ * @cmd_index:	Index of the SMC32 function ID
+ * @arg0:	SMC32 Argument 0
+ * @arg1:	SMC32 Argument 1
+ * @arg2:	SMC32 Argument 2
+ * @arg3:	SMC32 Argument 3
+ * @arg4:	SMC32 Argument 4
+ *
+ * Return:	size of read data on success, a negative value on error
+ */
+int meson_sm_call_read(void *buffer, unsigned int cmd_index, u32 arg0,
+		       u32 arg1, u32 arg2, u32 arg3, u32 arg4)
+{
+	u32 size;
+
+	if (!fw.chip)
+		return -ENOENT;
+
+	if (!fw.chip->cmd_shmem_out_base)
+		return -EINVAL;
+
+	if (meson_sm_call(cmd_index, &size, arg0, arg1, arg2, arg3, arg4) < 0)
+		return -EINVAL;
+
+	if (!size || size > fw.chip->shmem_size)
+		return -EINVAL;
+
+	if (buffer)
+		memcpy(buffer, fw.sm_shmem_out_base, size);
+
+	return size;
+}
+EXPORT_SYMBOL(meson_sm_call_read);
+
+/**
+ * meson_sm_call_write - send data to secure-monitor
+ *
+ * @buffer:	Buffer containing data to send
+ * @size:	Size of the data to send
+ * @cmd_index:	Index of the SMC32 function ID
+ * @arg0:	SMC32 Argument 0
+ * @arg1:	SMC32 Argument 1
+ * @arg2:	SMC32 Argument 2
+ * @arg3:	SMC32 Argument 3
+ * @arg4:	SMC32 Argument 4
+ *
+ * Return:	size of sent data on success, a negative value on error
+ */
+int meson_sm_call_write(void *buffer, unsigned int size, unsigned int cmd_index,
+			u32 arg0, u32 arg1, u32 arg2, u32 arg3, u32 arg4)
+{
+	u32 written;
+
+	if (!fw.chip)
+		return -ENOENT;
+
+	if (size > fw.chip->shmem_size)
+		return -EINVAL;
+
+	if (!fw.chip->cmd_shmem_in_base)
+		return -EINVAL;
+
+	memcpy(fw.sm_shmem_in_base, buffer, size);
+
+	if (meson_sm_call(cmd_index, &written, arg0, arg1, arg2, arg3, arg4) < 0)
+		return -EINVAL;
+
+	if (!written)
+		return -EINVAL;
+
+	return written;
+}
+EXPORT_SYMBOL(meson_sm_call_write);
+
+static const struct of_device_id meson_sm_ids[] = {
+	{ .compatible = "amlogic,meson-gxbb-sm", .data = &gxbb_chip },
+	{ /* sentinel */ },
+};
+
+int __init meson_sm_init(void)
+{
+	const struct meson_sm_chip *chip;
+	const struct of_device_id *matched_np;
+	struct device_node *np;
+
+	np = of_find_matching_node_and_match(NULL, meson_sm_ids, &matched_np);
+	if (!np)
+		return -ENODEV;
+
+	chip = matched_np->data;
+	if (!chip) {
+		pr_err("unable to setup secure-monitor data\n");
+		goto out;
+	}
+
+	if (chip->cmd_shmem_in_base) {
+		fw.sm_shmem_in_base = meson_sm_map_shmem(chip->cmd_shmem_in_base,
+							 chip->shmem_size);
+		if (WARN_ON(!fw.sm_shmem_in_base))
+			goto out;
+	}
+
+	if (chip->cmd_shmem_out_base) {
+		fw.sm_shmem_out_base = meson_sm_map_shmem(chip->cmd_shmem_out_base,
+							  chip->shmem_size);
+		if (WARN_ON(!fw.sm_shmem_out_base))
+			goto out_in_base;
+	}
+
+	fw.chip = chip;
+	pr_info("secure-monitor enabled\n");
+
+	return 0;
+
+out_in_base:
+	iounmap(fw.sm_shmem_in_base);
+out:
+	return -EINVAL;
+}
+device_initcall(meson_sm_init);

drivers/firmware/qcom_scm.c

-/* Copyright (c) 2010,2015, The Linux Foundation. All rights reserved.
+/*
+ * Qualcomm SCM driver
+ *
+ * Copyright (c) 2010,2015, The Linux Foundation. All rights reserved.
  * Copyright (C) 2015 Linaro Ltd.
  *
  * This program is free software; you can redistribute it and/or modify
@@ -12,7 +15,7 @@
  *
  */
 #include <linux/platform_device.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
 #include <linux/dma-mapping.h>
@@ -376,8 +379,6 @@ static const struct of_device_id qcom_scm_dt_match[] = {
 	{}
 };
 
-MODULE_DEVICE_TABLE(of, qcom_scm_dt_match);
-
 static struct platform_driver qcom_scm_driver = {
 	.driver = {
 		.name	= "qcom_scm",
@@ -414,14 +415,4 @@ static int __init qcom_scm_init(void)
 
 	return platform_driver_register(&qcom_scm_driver);
 }
-
 subsys_initcall(qcom_scm_init);
-
-static void __exit qcom_scm_exit(void)
-{
-	platform_driver_unregister(&qcom_scm_driver);
-}
-module_exit(qcom_scm_exit);
-
-MODULE_DESCRIPTION("Qualcomm SCM driver");
-MODULE_LICENSE("GPL v2");

drivers/media/rc/meson-ir.c

@@ -24,6 +24,7 @@
 
 #define DRIVER_NAME		"meson-ir"
 
+/* valid on all Meson platforms */
 #define IR_DEC_LDR_ACTIVE	0x00
 #define IR_DEC_LDR_IDLE		0x04
 #define IR_DEC_LDR_REPEAT	0x08
@@ -32,12 +33,21 @@
 #define IR_DEC_FRAME		0x14
 #define IR_DEC_STATUS		0x18
 #define IR_DEC_REG1		0x1c
+/* only available on Meson 8b and newer */
+#define IR_DEC_REG2		0x20
 
 #define REG0_RATE_MASK		(BIT(11) - 1)
 
-#define REG1_MODE_MASK		(BIT(7) | BIT(8))
-#define REG1_MODE_NEC		(0 << 7)
-#define REG1_MODE_GENERAL	(2 << 7)
+#define DECODE_MODE_NEC		0x0
+#define DECODE_MODE_RAW		0x2
+
+/* Meson 6b uses REG1 to configure the mode */
+#define REG1_MODE_MASK		GENMASK(8, 7)
+#define REG1_MODE_SHIFT		7
+
+/* Meson 8b / GXBB use REG2 to configure the mode */
+#define REG2_MODE_MASK		GENMASK(3, 0)
+#define REG2_MODE_SHIFT		0
 
 #define REG1_TIME_IV_SHIFT	16
 #define REG1_TIME_IV_MASK	((BIT(13) - 1) << REG1_TIME_IV_SHIFT)
@@ -158,8 +168,15 @@ static int meson_ir_probe(struct platform_device *pdev)
 	/* Reset the decoder */
 	meson_ir_set_mask(ir, IR_DEC_REG1, REG1_RESET, REG1_RESET);
 	meson_ir_set_mask(ir, IR_DEC_REG1, REG1_RESET, 0);
-	/* Set general operation mode */
-	meson_ir_set_mask(ir, IR_DEC_REG1, REG1_MODE_MASK, REG1_MODE_GENERAL);
+
+	/* Set general operation mode (= raw/software decoding) */
+	if (of_device_is_compatible(node, "amlogic,meson6-ir"))
+		meson_ir_set_mask(ir, IR_DEC_REG1, REG1_MODE_MASK,
+				  DECODE_MODE_RAW << REG1_MODE_SHIFT);
+	else
+		meson_ir_set_mask(ir, IR_DEC_REG2, REG2_MODE_MASK,
+				  DECODE_MODE_RAW << REG2_MODE_SHIFT);
+
 	/* Set rate */
 	meson_ir_set_mask(ir, IR_DEC_REG0, REG0_RATE_MASK, MESON_TRATE - 1);
 	/* IRQ on rising and falling edges */
@@ -197,6 +214,8 @@ static int meson_ir_remove(struct platform_device *pdev)
 
 static const struct of_device_id meson_ir_match[] = {
 	{ .compatible = "amlogic,meson6-ir" },
+	{ .compatible = "amlogic,meson8b-ir" },
+	{ .compatible = "amlogic,meson-gxbb-ir" },
 	{ },
 };
 

drivers/memory/atmel-ebi.c

@@ -410,10 +410,7 @@ static int at91sam9_ebi_init(struct at91_ebi *ebi)
 
 	field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
 	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
-	if (IS_ERR(fields->mode))
-		return PTR_ERR(fields->mode);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(fields->mode);
 }
 
 static int sama5d3_ebi_init(struct at91_ebi *ebi)
@@ -441,10 +438,7 @@ static int sama5d3_ebi_init(struct at91_ebi *ebi)
 
 	field.reg = SAMA5_SMC_MODE(SAMA5_SMC_GENERIC);
 	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
-	if (IS_ERR(fields->mode))
-		return PTR_ERR(fields->mode);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(fields->mode);
 }
 
 static int at91_ebi_dev_setup(struct at91_ebi *ebi, struct device_node *np,

drivers/memory/atmel-sdramc.c

@@ -53,12 +53,10 @@ static const struct of_device_id atmel_ramc_of_match[] = {
 
 static int atmel_ramc_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
 	const struct at91_ramc_caps *caps;
 	struct clk *clk;
 
-	match = of_match_device(atmel_ramc_of_match, &pdev->dev);
-	caps = match->data;
+	caps = of_device_get_match_data(&pdev->dev);
 
 	if (caps->has_ddrck) {
 		clk = devm_clk_get(&pdev->dev, "ddrck");

drivers/memory/omap-gpmc.c

@@ -350,8 +350,8 @@ static unsigned int gpmc_ps_to_ticks(unsigned int time_ps)
 	return (time_ps + tick_ps - 1) / tick_ps;
 }
 
-unsigned int gpmc_clk_ticks_to_ns(unsigned ticks, int cs,
-				  enum gpmc_clk_domain cd)
+static unsigned int gpmc_clk_ticks_to_ns(unsigned int ticks, int cs,
+					 enum gpmc_clk_domain cd)
 {
 	return ticks * gpmc_get_clk_period(cs, cd) / 1000;
 }
@@ -2143,9 +2143,7 @@ static int gpmc_probe_generic_child(struct platform_device *pdev,
 	ret = -ENODEV;
 
 err_cs:
-	if (waitpin_desc)
-		gpiochip_free_own_desc(waitpin_desc);
-
+	gpiochip_free_own_desc(waitpin_desc);
 err:
 	gpmc_cs_free(cs);
 
@@ -2265,7 +2263,7 @@ static int gpmc_gpio_init(struct gpmc_device *gpmc)
 	gpmc->gpio_chip.get = gpmc_gpio_get;
 	gpmc->gpio_chip.base = -1;
 
-	ret = gpiochip_add(&gpmc->gpio_chip);
+	ret = devm_gpiochip_add_data(gpmc->dev, &gpmc->gpio_chip, NULL);
 	if (ret < 0) {
 		dev_err(gpmc->dev, "could not register gpio chip: %d\n", ret);
 		return ret;
@@ -2274,11 +2272,6 @@ static int gpmc_gpio_init(struct gpmc_device *gpmc)
 	return 0;
 }
 
-static void gpmc_gpio_exit(struct gpmc_device *gpmc)
-{
-	gpiochip_remove(&gpmc->gpio_chip);
-}
-
 static int gpmc_probe(struct platform_device *pdev)
 {
 	int rc;
@@ -2365,15 +2358,13 @@ static int gpmc_probe(struct platform_device *pdev)
 	rc = gpmc_setup_irq(gpmc);
 	if (rc) {
 		dev_err(gpmc->dev, "gpmc_setup_irq failed\n");
-		goto setup_irq_failed;
+		goto gpio_init_failed;
 	}
 
 	gpmc_probe_dt_children(pdev);
 
 	return 0;
 
-setup_irq_failed:
-	gpmc_gpio_exit(gpmc);
 gpio_init_failed:
 	gpmc_mem_exit();
 	pm_runtime_put_sync(&pdev->dev);
@@ -2387,7 +2378,6 @@ static int gpmc_remove(struct platform_device *pdev)
 	struct gpmc_device *gpmc = platform_get_drvdata(pdev);
 
 	gpmc_free_irq(gpmc);
-	gpmc_gpio_exit(gpmc);
 	gpmc_mem_exit();
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);

drivers/nvmem/Kconfig

@@ -101,4 +101,14 @@ config NVMEM_VF610_OCOTP
 	  This driver can also be build as a module. If so, the module will
 	  be called nvmem-vf610-ocotp.
 
+config MESON_EFUSE
+	tristate "Amlogic eFuse Support"
+	depends on (ARCH_MESON || COMPILE_TEST) && MESON_SM
+	help
+	  This is a driver to retrieve specific values from the eFuse found on
+	  the Amlogic Meson SoCs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called nvmem_meson_efuse.
+
 endif

drivers/nvmem/Makefile

@@ -22,3 +22,5 @@ obj-$(CONFIG_NVMEM_SUNXI_SID)	+= nvmem_sunxi_sid.o
 nvmem_sunxi_sid-y		:= sunxi_sid.o
 obj-$(CONFIG_NVMEM_VF610_OCOTP)	+= nvmem-vf610-ocotp.o
 nvmem-vf610-ocotp-y		:= vf610-ocotp.o
+obj-$(CONFIG_MESON_EFUSE)	+= nvmem_meson_efuse.o
+nvmem_meson_efuse-y		:= meson-efuse.o

drivers/nvmem/meson-efuse.c

+/*
+ * Amlogic eFuse Driver
+ *
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include <linux/firmware/meson/meson_sm.h>
+
+static int meson_efuse_read(void *context, unsigned int offset,
+			    void *val, size_t bytes)
+{
+	u8 *buf = val;
+	int ret;
+
+	ret = meson_sm_call_read(buf, SM_EFUSE_READ, offset,
+				 bytes, 0, 0, 0);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static struct nvmem_config econfig = {
+	.name = "meson-efuse",
+	.owner = THIS_MODULE,
+	.stride = 1,
+	.word_size = 1,
+	.read_only = true,
+};
+
+static const struct of_device_id meson_efuse_match[] = {
+	{ .compatible = "amlogic,meson-gxbb-efuse", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, meson_efuse_match);
+
+static int meson_efuse_probe(struct platform_device *pdev)
+{
+	struct nvmem_device *nvmem;
+	unsigned int size;
+
+	if (meson_sm_call(SM_EFUSE_USER_MAX, &size, 0, 0, 0, 0, 0) < 0)
+		return -EINVAL;
+
+	econfig.dev = &pdev->dev;
+	econfig.reg_read = meson_efuse_read;
+	econfig.size = size;
+
+	nvmem = nvmem_register(&econfig);
+	if (IS_ERR(nvmem))
+		return PTR_ERR(nvmem);
+
+	platform_set_drvdata(pdev, nvmem);
+
+	return 0;
+}
+
+static int meson_efuse_remove(struct platform_device *pdev)
+{
+	struct nvmem_device *nvmem = platform_get_drvdata(pdev);
+
+	return nvmem_unregister(nvmem);
+}
+
+static struct platform_driver meson_efuse_driver = {
+	.probe = meson_efuse_probe,
+	.remove = meson_efuse_remove,
+	.driver = {
+		.name = "meson-efuse",
+		.of_match_table = meson_efuse_match,
+	},
+};
+
+module_platform_driver(meson_efuse_driver);
+
+MODULE_AUTHOR("Carlo Caione <carlo@endlessm.com>");
+MODULE_DESCRIPTION("Amlogic Meson NVMEM driver");
+MODULE_LICENSE("GPL v2");

drivers/perf/Kconfig

@@ -12,4 +12,11 @@ config ARM_PMU
 	  Say y if you want to use CPU performance monitors on ARM-based
 	  systems.
 
+config XGENE_PMU
+        depends on PERF_EVENTS && ARCH_XGENE
+        bool "APM X-Gene SoC PMU"
+        default n
+        help
+          Say y if you want to use APM X-Gene SoC performance monitors.
+
 endmenu

drivers/perf/Makefile

 obj-$(CONFIG_ARM_PMU) += arm_pmu.o
+obj-$(CONFIG_XGENE_PMU) += xgene_pmu.o

drivers/pinctrl/mvebu/pinctrl-orion.c

@@ -64,11 +64,11 @@ static int orion_mpp_ctrl_set(unsigned pid, unsigned long config)
 	return 0;
 }
 
-#define V(f5181l, f5182, f5281) \
-	((f5181l << 0) | (f5182 << 1) | (f5281 << 2))
+#define V(f5181, f5182, f5281) \
+	((f5181 << 0) | (f5182 << 1) | (f5281 << 2))
 
 enum orion_variant {
-	V_5181L = V(1, 0, 0),
+	V_5181  = V(1, 0, 0),
 	V_5182  = V(0, 1, 0),
 	V_5281  = V(0, 0, 1),
 	V_ALL   = V(1, 1, 1),
@@ -103,13 +103,13 @@ static struct mvebu_mpp_mode orion_mpp_modes[] = {
 		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,        V_ALL),
 		 MPP_VAR_FUNCTION(0x2, "pci", "req5",       V_ALL),
 		 MPP_VAR_FUNCTION(0x4, "nand", "re0",       V_5182 | V_5281),
-		 MPP_VAR_FUNCTION(0x5, "pci-1", "clk",      V_5181L),
+		 MPP_VAR_FUNCTION(0x5, "pci-1", "clk",      V_5181),
 		 MPP_VAR_FUNCTION(0x5, "sata0", "act",      V_5182)),
 	MPP_MODE(7,
 		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,        V_ALL),
 		 MPP_VAR_FUNCTION(0x2, "pci", "gnt5",       V_ALL),
 		 MPP_VAR_FUNCTION(0x4, "nand", "we0",       V_5182 | V_5281),
-		 MPP_VAR_FUNCTION(0x5, "pci-1", "clk",      V_5181L),
+		 MPP_VAR_FUNCTION(0x5, "pci-1", "clk",      V_5181),
 		 MPP_VAR_FUNCTION(0x5, "sata1", "act",      V_5182)),
 	MPP_MODE(8,
 		 MPP_VAR_FUNCTION(0x0, "gpio", NULL,        V_ALL),
@@ -165,7 +165,7 @@ static struct mvebu_mpp_ctrl orion_mpp_controls[] = {
 	MPP_FUNC_CTRL(0, 19, NULL, orion_mpp_ctrl),
 };
 
-static struct pinctrl_gpio_range mv88f5181l_gpio_ranges[] = {
+static struct pinctrl_gpio_range mv88f5181_gpio_ranges[] = {
 	MPP_GPIO_RANGE(0, 0, 0, 16),
 };
 
@@ -177,14 +177,14 @@ static struct pinctrl_gpio_range mv88f5281_gpio_ranges[] = {
 	MPP_GPIO_RANGE(0, 0, 0, 16),
 };
 
-static struct mvebu_pinctrl_soc_info mv88f5181l_info = {
-	.variant = V_5181L,
+static struct mvebu_pinctrl_soc_info mv88f5181_info = {
+	.variant = V_5181,
 	.controls = orion_mpp_controls,
 	.ncontrols = ARRAY_SIZE(orion_mpp_controls),
 	.modes = orion_mpp_modes,
 	.nmodes = ARRAY_SIZE(orion_mpp_modes),
-	.gpioranges = mv88f5181l_gpio_ranges,
-	.ngpioranges = ARRAY_SIZE(mv88f5181l_gpio_ranges),
+	.gpioranges = mv88f5181_gpio_ranges,
+	.ngpioranges = ARRAY_SIZE(mv88f5181_gpio_ranges),
 };
 
 static struct mvebu_pinctrl_soc_info mv88f5182_info = {
@@ -212,7 +212,8 @@ static struct mvebu_pinctrl_soc_info mv88f5281_info = {
  * muxing, they are identical.
  */
 static const struct of_device_id orion_pinctrl_of_match[] = {
-	{ .compatible = "marvell,88f5181l-pinctrl", .data = &mv88f5181l_info },
+	{ .compatible = "marvell,88f5181-pinctrl", .data = &mv88f5181_info },
+	{ .compatible = "marvell,88f5181l-pinctrl", .data = &mv88f5181_info },
 	{ .compatible = "marvell,88f5182-pinctrl", .data = &mv88f5182_info },
 	{ .compatible = "marvell,88f5281-pinctrl", .data = &mv88f5281_info },
 	{ }

drivers/reset/Kconfig

@@ -14,9 +14,58 @@ menuconfig RESET_CONTROLLER
 
 if RESET_CONTROLLER
 
+config RESET_ATH79
+	bool "AR71xx Reset Driver" if COMPILE_TEST
+	default ATH79
+	help
+	  This enables the ATH79 reset controller driver that supports the
+	  AR71xx SoC reset controller.
+
+config RESET_BERLIN
+	bool "Berlin Reset Driver" if COMPILE_TEST
+	default ARCH_BERLIN
+	help
+	  This enables the reset controller driver for Marvell Berlin SoCs.
+
+config RESET_LPC18XX
+	bool "LPC18xx/43xx Reset Driver" if COMPILE_TEST
+	default ARCH_LPC18XX
+	help
+	  This enables the reset controller driver for NXP LPC18xx/43xx SoCs.
+
+config RESET_MESON
+	bool "Meson Reset Driver" if COMPILE_TEST
+	default ARCH_MESON
+	help
+	  This enables the reset driver for Amlogic Meson SoCs.
+
 config RESET_OXNAS
 	bool
 
+config RESET_PISTACHIO
+	bool "Pistachio Reset Driver" if COMPILE_TEST
+	default MACH_PISTACHIO
+	help
+	  This enables the reset driver for ImgTec Pistachio SoCs.
+
+config RESET_SOCFPGA
+	bool "SoCFPGA Reset Driver" if COMPILE_TEST
+	default ARCH_SOCFPGA
+	help
+	  This enables the reset controller driver for Altera SoCFPGAs.
+
+config RESET_STM32
+	bool "STM32 Reset Driver" if COMPILE_TEST
+	default ARCH_STM32
+	help
+	  This enables the RCC reset controller driver for STM32 MCUs.
+
+config RESET_SUNXI
+	bool "Allwinner SoCs Reset Driver" if COMPILE_TEST && !ARCH_SUNXI
+	default ARCH_SUNXI
+	help
+	  This enables the reset driver for Allwinner SoCs.
+
 config TI_SYSCON_RESET
 	tristate "TI SYSCON Reset Driver"
 	depends on HAS_IOMEM
@@ -27,6 +76,22 @@ config TI_SYSCON_RESET
 	  you wish to use the reset framework for such memory-mapped devices,
 	  say Y here. Otherwise, say N.
 
+config RESET_UNIPHIER
+	tristate "Reset controller driver for UniPhier SoCs"
+	depends on ARCH_UNIPHIER || COMPILE_TEST
+	depends on OF && MFD_SYSCON
+	default ARCH_UNIPHIER
+	help
+	  Support for reset controllers on UniPhier SoCs.
+	  Say Y if you want to control reset signals provided by System Control
+	  block, Media I/O block, Peripheral Block.
+
+config RESET_ZYNQ
+	bool "ZYNQ Reset Driver" if COMPILE_TEST
+	default ARCH_ZYNQ
+	help
+	  This enables the reset controller driver for Xilinx Zynq SoCs.
+
 source "drivers/reset/sti/Kconfig"
 source "drivers/reset/hisilicon/Kconfig"
 

drivers/reset/Makefile

 obj-y += core.o
-obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
-obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
-obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
-obj-$(CONFIG_MACH_PISTACHIO) += reset-pistachio.o
-obj-$(CONFIG_ARCH_MESON) += reset-meson.o
-obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
+obj-y += hisilicon/
 obj-$(CONFIG_ARCH_STI) += sti/
-obj-$(CONFIG_ARCH_HISI) += hisilicon/
-obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
-obj-$(CONFIG_ATH79) += reset-ath79.o
+obj-$(CONFIG_RESET_ATH79) += reset-ath79.o
+obj-$(CONFIG_RESET_BERLIN) += reset-berlin.o
+obj-$(CONFIG_RESET_LPC18XX) += reset-lpc18xx.o
+obj-$(CONFIG_RESET_MESON) += reset-meson.o
 obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
+obj-$(CONFIG_RESET_PISTACHIO) += reset-pistachio.o
+obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o
+obj-$(CONFIG_RESET_STM32) += reset-stm32.o
+obj-$(CONFIG_RESET_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_TI_SYSCON_RESET) += reset-ti-syscon.o
+obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
+obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o

drivers/reset/core.c

@@ -138,7 +138,8 @@ EXPORT_SYMBOL_GPL(devm_reset_controller_register);
  */
 int reset_control_reset(struct reset_control *rstc)
 {
-	if (WARN_ON(rstc->shared))
+	if (WARN_ON(IS_ERR_OR_NULL(rstc)) ||
+	    WARN_ON(rstc->shared))
 		return -EINVAL;
 
 	if (rstc->rcdev->ops->reset)
@@ -161,6 +162,9 @@ EXPORT_SYMBOL_GPL(reset_control_reset);
  */
 int reset_control_assert(struct reset_control *rstc)
 {
+	if (WARN_ON(IS_ERR_OR_NULL(rstc)))
+		return -EINVAL;
+
 	if (!rstc->rcdev->ops->assert)
 		return -ENOTSUPP;
 
@@ -184,6 +188,9 @@ EXPORT_SYMBOL_GPL(reset_control_assert);
  */
 int reset_control_deassert(struct reset_control *rstc)
 {
+	if (WARN_ON(IS_ERR_OR_NULL(rstc)))
+		return -EINVAL;
+
 	if (!rstc->rcdev->ops->deassert)
 		return -ENOTSUPP;
 
@@ -204,6 +211,9 @@ EXPORT_SYMBOL_GPL(reset_control_deassert);
  */
 int reset_control_status(struct reset_control *rstc)
 {
+	if (WARN_ON(IS_ERR_OR_NULL(rstc)))
+		return -EINVAL;
+
 	if (rstc->rcdev->ops->status)
 		return rstc->rcdev->ops->status(rstc->rcdev, rstc->id);
 

drivers/reset/hisilicon/Kconfig

 config COMMON_RESET_HI6220
 	tristate "Hi6220 Reset Driver"
-	depends on (ARCH_HISI && RESET_CONTROLLER)
+	depends on ARCH_HISI || COMPILE_TEST
+	default ARCH_HISI
 	help
 	  Build the Hisilicon Hi6220 reset driver.

drivers/reset/reset-ath79.c

@@ -12,6 +12,7 @@
  * GNU General Public License for more details.
  */
 
+#include <linux/io.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/reset-controller.h>

drivers/reset/reset-socfpga.c

@@ -28,7 +28,6 @@
 struct socfpga_reset_data {
 	spinlock_t			lock;
 	void __iomem			*membase;
-	u32				modrst_offset;
 	struct reset_controller_dev	rcdev;
 };
 
@@ -45,9 +44,8 @@ static int socfpga_reset_assert(struct reset_controller_dev *rcdev,
 
 	spin_lock_irqsave(&data->lock, flags);
 
-	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
-	writel(reg | BIT(offset), data->membase + data->modrst_offset +
-				 (bank * NR_BANKS));
+	reg = readl(data->membase + (bank * NR_BANKS));
+	writel(reg | BIT(offset), data->membase + (bank * NR_BANKS));
 	spin_unlock_irqrestore(&data->lock, flags);
 
 	return 0;
@@ -67,9 +65,8 @@ static int socfpga_reset_deassert(struct reset_controller_dev *rcdev,
 
 	spin_lock_irqsave(&data->lock, flags);
 
-	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
-	writel(reg & ~BIT(offset), data->membase + data->modrst_offset +
-				  (bank * NR_BANKS));
+	reg = readl(data->membase + (bank * NR_BANKS));
+	writel(reg & ~BIT(offset), data->membase + (bank * NR_BANKS));
 
 	spin_unlock_irqrestore(&data->lock, flags);
 
@@ -85,7 +82,7 @@ static int socfpga_reset_status(struct reset_controller_dev *rcdev,
 	int offset = id % BITS_PER_LONG;
 	u32 reg;
 
-	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
+	reg = readl(data->membase + (bank * NR_BANKS));
 
 	return !(reg & BIT(offset));
 }
@@ -102,6 +99,7 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 	struct resource *res;
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
+	u32 modrst_offset;
 
 	/*
 	 * The binding was mainlined without the required property.
@@ -122,10 +120,11 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 	if (IS_ERR(data->membase))
 		return PTR_ERR(data->membase);
 
-	if (of_property_read_u32(np, "altr,modrst-offset", &data->modrst_offset)) {
+	if (of_property_read_u32(np, "altr,modrst-offset", &modrst_offset)) {
 		dev_warn(dev, "missing altr,modrst-offset property, assuming 0x10!\n");
-		data->modrst_offset = 0x10;
+		modrst_offset = 0x10;
 	}
+	data->membase += modrst_offset;
 
 	spin_lock_init(&data->lock);
 

drivers/reset/reset-stm32.c

+/*
+ * Copyright (C) Maxime Coquelin 2015
+ * Author:  Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ * License terms:  GNU General Public License (GPL), version 2
+ *
+ * Heavily based on sunxi driver from Maxime Ripard.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+struct stm32_reset_data {
+	spinlock_t			lock;
+	void __iomem			*membase;
+	struct reset_controller_dev	rcdev;
+};
+
+static int stm32_reset_assert(struct reset_controller_dev *rcdev,
+			      unsigned long id)
+{
+	struct stm32_reset_data *data = container_of(rcdev,
+						     struct stm32_reset_data,
+						     rcdev);
+	int bank = id / BITS_PER_LONG;
+	int offset = id % BITS_PER_LONG;
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&data->lock, flags);
+
+	reg = readl(data->membase + (bank * 4));
+	writel(reg | BIT(offset), data->membase + (bank * 4));
+
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	return 0;
+}
+
+static int stm32_reset_deassert(struct reset_controller_dev *rcdev,
+				unsigned long id)
+{
+	struct stm32_reset_data *data = container_of(rcdev,
+						     struct stm32_reset_data,
+						     rcdev);
+	int bank = id / BITS_PER_LONG;
+	int offset = id % BITS_PER_LONG;
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&data->lock, flags);
+
+	reg = readl(data->membase + (bank * 4));
+	writel(reg & ~BIT(offset), data->membase + (bank * 4));
+
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	return 0;
+}
+
+static const struct reset_control_ops stm32_reset_ops = {
+	.assert		= stm32_reset_assert,
+	.deassert	= stm32_reset_deassert,
+};
+
+static const struct of_device_id stm32_reset_dt_ids[] = {
+	 { .compatible = "st,stm32-rcc", },
+	 { /* sentinel */ },
+};
+
+static int stm32_reset_probe(struct platform_device *pdev)
+{
+	struct stm32_reset_data *data;
+	struct resource *res;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(data->membase))
+		return PTR_ERR(data->membase);
+
+	spin_lock_init(&data->lock);
+
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.nr_resets = resource_size(res) * 8;
+	data->rcdev.ops = &stm32_reset_ops;
+	data->rcdev.of_node = pdev->dev.of_node;
+
+	return devm_reset_controller_register(&pdev->dev, &data->rcdev);
+}
+
+static struct platform_driver stm32_reset_driver = {
+	.probe	= stm32_reset_probe,
+	.driver = {
+		.name		= "stm32-rcc-reset",
+		.of_match_table	= stm32_reset_dt_ids,
+	},
+};
+builtin_platform_driver(stm32_reset_driver);

drivers/soc/mediatek/mtk-pmic-wrap.c

@@ -583,7 +583,7 @@ static int pwrap_wait_for_state(struct pmic_wrapper *wrp,
 {
 	unsigned long timeout;
 
-	timeout = jiffies + usecs_to_jiffies(255);
+	timeout = jiffies + usecs_to_jiffies(10000);
 
 	do {
 		if (time_after(jiffies, timeout))

drivers/soc/qcom/smem.c

@@ -740,7 +740,8 @@ static int qcom_smem_probe(struct platform_device *pdev)
 
 	hwlock_id = of_hwspin_lock_get_id(pdev->dev.of_node, 0);
 	if (hwlock_id < 0) {
-		dev_err(&pdev->dev, "failed to retrieve hwlock\n");
+		if (hwlock_id != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "failed to retrieve hwlock\n");
 		return hwlock_id;
 	}
 

drivers/soc/rockchip/pm_domains.c

@@ -27,6 +27,7 @@ struct rockchip_domain_info {
 	int req_mask;
 	int idle_mask;
 	int ack_mask;
+	bool active_wakeup;
 };
 
 struct rockchip_pmu_info {
@@ -75,23 +76,24 @@ struct rockchip_pmu {
 
 #define to_rockchip_pd(gpd) container_of(gpd, struct rockchip_pm_domain, genpd)
 
-#define DOMAIN(pwr, status, req, idle, ack)	\
+#define DOMAIN(pwr, status, req, idle, ack, wakeup)	\
 {						\
 	.pwr_mask = (pwr >= 0) ? BIT(pwr) : 0,		\
 	.status_mask = (status >= 0) ? BIT(status) : 0,	\
 	.req_mask = (req >= 0) ? BIT(req) : 0,		\
 	.idle_mask = (idle >= 0) ? BIT(idle) : 0,	\
 	.ack_mask = (ack >= 0) ? BIT(ack) : 0,		\
+	.active_wakeup = wakeup,			\
 }
 
-#define DOMAIN_RK3288(pwr, status, req)		\
-	DOMAIN(pwr, status, req, req, (req) + 16)
+#define DOMAIN_RK3288(pwr, status, req, wakeup)		\
+	DOMAIN(pwr, status, req, req, (req) + 16, wakeup)
 
-#define DOMAIN_RK3368(pwr, status, req)		\
-	DOMAIN(pwr, status, req, (req) + 16, req)
+#define DOMAIN_RK3368(pwr, status, req, wakeup)		\
+	DOMAIN(pwr, status, req, (req) + 16, req, wakeup)
 
-#define DOMAIN_RK3399(pwr, status, req)                \
-	DOMAIN(pwr, status, req, req, req)
+#define DOMAIN_RK3399(pwr, status, req, wakeup)		\
+	DOMAIN(pwr, status, req, req, req, wakeup)
 
 static bool rockchip_pmu_domain_is_idle(struct rockchip_pm_domain *pd)
 {
@@ -295,6 +297,17 @@ static void rockchip_pd_detach_dev(struct generic_pm_domain *genpd,
 	pm_clk_destroy(dev);
 }
 
+static bool rockchip_active_wakeup(struct device *dev)
+{
+	struct generic_pm_domain *genpd;
+	struct rockchip_pm_domain *pd;
+
+	genpd = pd_to_genpd(dev->pm_domain);
+	pd = container_of(genpd, struct rockchip_pm_domain, genpd);
+
+	return pd->info->active_wakeup;
+}
+
 static int rockchip_pm_add_one_domain(struct rockchip_pmu *pmu,
 				      struct device_node *node)
 {
@@ -415,6 +428,7 @@ static int rockchip_pm_add_one_domain(struct rockchip_pmu *pmu,
 	pd->genpd.power_on = rockchip_pd_power_on;
 	pd->genpd.attach_dev = rockchip_pd_attach_dev;
 	pd->genpd.detach_dev = rockchip_pd_detach_dev;
+	pd->genpd.dev_ops.active_wakeup = rockchip_active_wakeup;
 	pd->genpd.flags = GENPD_FLAG_PM_CLK;
 	pm_genpd_init(&pd->genpd, NULL, false);
 
@@ -623,48 +637,48 @@ static int rockchip_pm_domain_probe(struct platform_device *pdev)
 }
 
 static const struct rockchip_domain_info rk3288_pm_domains[] = {
-	[RK3288_PD_VIO]		= DOMAIN_RK3288(7, 7, 4),
-	[RK3288_PD_HEVC]	= DOMAIN_RK3288(14, 10, 9),
-	[RK3288_PD_VIDEO]	= DOMAIN_RK3288(8, 8, 3),
-	[RK3288_PD_GPU]		= DOMAIN_RK3288(9, 9, 2),
+	[RK3288_PD_VIO]		= DOMAIN_RK3288(7, 7, 4, false),
+	[RK3288_PD_HEVC]	= DOMAIN_RK3288(14, 10, 9, false),
+	[RK3288_PD_VIDEO]	= DOMAIN_RK3288(8, 8, 3, false),
+	[RK3288_PD_GPU]		= DOMAIN_RK3288(9, 9, 2, false),
 };
 
 static const struct rockchip_domain_info rk3368_pm_domains[] = {
-	[RK3368_PD_PERI]	= DOMAIN_RK3368(13, 12, 6),
-	[RK3368_PD_VIO]		= DOMAIN_RK3368(15, 14, 8),
-	[RK3368_PD_VIDEO]	= DOMAIN_RK3368(14, 13, 7),
-	[RK3368_PD_GPU_0]	= DOMAIN_RK3368(16, 15, 2),
-	[RK3368_PD_GPU_1]	= DOMAIN_RK3368(17, 16, 2),
+	[RK3368_PD_PERI]	= DOMAIN_RK3368(13, 12, 6, true),
+	[RK3368_PD_VIO]		= DOMAIN_RK3368(15, 14, 8, false),
+	[RK3368_PD_VIDEO]	= DOMAIN_RK3368(14, 13, 7, false),
+	[RK3368_PD_GPU_0]	= DOMAIN_RK3368(16, 15, 2, false),
+	[RK3368_PD_GPU_1]	= DOMAIN_RK3368(17, 16, 2, false),
 };
 
 static const struct rockchip_domain_info rk3399_pm_domains[] = {
-	[RK3399_PD_TCPD0]	= DOMAIN_RK3399(8, 8, -1),
-	[RK3399_PD_TCPD1]	= DOMAIN_RK3399(9, 9, -1),
-	[RK3399_PD_CCI]		= DOMAIN_RK3399(10, 10, -1),
-	[RK3399_PD_CCI0]	= DOMAIN_RK3399(-1, -1, 15),
-	[RK3399_PD_CCI1]	= DOMAIN_RK3399(-1, -1, 16),
-	[RK3399_PD_PERILP]	= DOMAIN_RK3399(11, 11, 1),
-	[RK3399_PD_PERIHP]	= DOMAIN_RK3399(12, 12, 2),
-	[RK3399_PD_CENTER]	= DOMAIN_RK3399(13, 13, 14),
-	[RK3399_PD_VIO]		= DOMAIN_RK3399(14, 14, 17),
-	[RK3399_PD_GPU]		= DOMAIN_RK3399(15, 15, 0),
-	[RK3399_PD_VCODEC]	= DOMAIN_RK3399(16, 16, 3),
-	[RK3399_PD_VDU]		= DOMAIN_RK3399(17, 17, 4),
-	[RK3399_PD_RGA]		= DOMAIN_RK3399(18, 18, 5),
-	[RK3399_PD_IEP]		= DOMAIN_RK3399(19, 19, 6),
-	[RK3399_PD_VO]		= DOMAIN_RK3399(20, 20, -1),
-	[RK3399_PD_VOPB]	= DOMAIN_RK3399(-1, -1, 7),
-	[RK3399_PD_VOPL]	= DOMAIN_RK3399(-1, -1, 8),
-	[RK3399_PD_ISP0]	= DOMAIN_RK3399(22, 22, 9),
-	[RK3399_PD_ISP1]	= DOMAIN_RK3399(23, 23, 10),
-	[RK3399_PD_HDCP]	= DOMAIN_RK3399(24, 24, 11),
-	[RK3399_PD_GMAC]	= DOMAIN_RK3399(25, 25, 23),
-	[RK3399_PD_EMMC]	= DOMAIN_RK3399(26, 26, 24),
-	[RK3399_PD_USB3]	= DOMAIN_RK3399(27, 27, 12),
-	[RK3399_PD_EDP]		= DOMAIN_RK3399(28, 28, 22),
-	[RK3399_PD_GIC]		= DOMAIN_RK3399(29, 29, 27),
-	[RK3399_PD_SD]		= DOMAIN_RK3399(30, 30, 28),
-	[RK3399_PD_SDIOAUDIO]	= DOMAIN_RK3399(31, 31, 29),
+	[RK3399_PD_TCPD0]	= DOMAIN_RK3399(8, 8, -1, false),
+	[RK3399_PD_TCPD1]	= DOMAIN_RK3399(9, 9, -1, false),
+	[RK3399_PD_CCI]		= DOMAIN_RK3399(10, 10, -1, true),
+	[RK3399_PD_CCI0]	= DOMAIN_RK3399(-1, -1, 15, true),
+	[RK3399_PD_CCI1]	= DOMAIN_RK3399(-1, -1, 16, true),
+	[RK3399_PD_PERILP]	= DOMAIN_RK3399(11, 11, 1, true),
+	[RK3399_PD_PERIHP]	= DOMAIN_RK3399(12, 12, 2, true),
+	[RK3399_PD_CENTER]	= DOMAIN_RK3399(13, 13, 14, true),
+	[RK3399_PD_VIO]		= DOMAIN_RK3399(14, 14, 17, false),
+	[RK3399_PD_GPU]		= DOMAIN_RK3399(15, 15, 0, false),
+	[RK3399_PD_VCODEC]	= DOMAIN_RK3399(16, 16, 3, false),
+	[RK3399_PD_VDU]		= DOMAIN_RK3399(17, 17, 4, false),
+	[RK3399_PD_RGA]		= DOMAIN_RK3399(18, 18, 5, false),
+	[RK3399_PD_IEP]		= DOMAIN_RK3399(19, 19, 6, false),
+	[RK3399_PD_VO]		= DOMAIN_RK3399(20, 20, -1, false),
+	[RK3399_PD_VOPB]	= DOMAIN_RK3399(-1, -1, 7, false),
+	[RK3399_PD_VOPL]	= DOMAIN_RK3399(-1, -1, 8, false),
+	[RK3399_PD_ISP0]	= DOMAIN_RK3399(22, 22, 9, false),
+	[RK3399_PD_ISP1]	= DOMAIN_RK3399(23, 23, 10, false),
+	[RK3399_PD_HDCP]	= DOMAIN_RK3399(24, 24, 11, false),
+	[RK3399_PD_GMAC]	= DOMAIN_RK3399(25, 25, 23, true),
+	[RK3399_PD_EMMC]	= DOMAIN_RK3399(26, 26, 24, true),
+	[RK3399_PD_USB3]	= DOMAIN_RK3399(27, 27, 12, true),
+	[RK3399_PD_EDP]		= DOMAIN_RK3399(28, 28, 22, false),
+	[RK3399_PD_GIC]		= DOMAIN_RK3399(29, 29, 27, true),
+	[RK3399_PD_SD]		= DOMAIN_RK3399(30, 30, 28, true),
+	[RK3399_PD_SDIOAUDIO]	= DOMAIN_RK3399(31, 31, 29, true),
 };
 
 static const struct rockchip_pmu_info rk3288_pmu = {

drivers/soc/tegra/pmc.c

@@ -967,8 +967,8 @@ static void tegra_io_rail_unprepare(void)
 
 int tegra_io_rail_power_on(unsigned int id)
 {
-	unsigned long request, status, value;
-	unsigned int bit, mask;
+	unsigned long request, status;
+	unsigned int bit;
 	int err;
 
 	mutex_lock(&pmc->powergates_lock);
@@ -977,15 +977,9 @@ int tegra_io_rail_power_on(unsigned int id)
 	if (err)
 		goto error;
 
-	mask = 1 << bit;
+	tegra_pmc_writel(IO_DPD_REQ_CODE_OFF | BIT(bit), request);
 
-	value = tegra_pmc_readl(request);
-	value |= mask;
-	value &= ~IO_DPD_REQ_CODE_MASK;
-	value |= IO_DPD_REQ_CODE_OFF;
-	tegra_pmc_writel(value, request);
-
-	err = tegra_io_rail_poll(status, mask, 0, 250);
+	err = tegra_io_rail_poll(status, BIT(bit), 0, 250);
 	if (err) {
 		pr_info("tegra_io_rail_poll() failed: %d\n", err);
 		goto error;
@@ -1002,8 +996,8 @@ EXPORT_SYMBOL(tegra_io_rail_power_on);
 
 int tegra_io_rail_power_off(unsigned int id)
 {
-	unsigned long request, status, value;
-	unsigned int bit, mask;
+	unsigned long request, status;
+	unsigned int bit;
 	int err;
 
 	mutex_lock(&pmc->powergates_lock);
@@ -1014,15 +1008,9 @@ int tegra_io_rail_power_off(unsigned int id)
 		goto error;
 	}
 
-	mask = 1 << bit;
-
-	value = tegra_pmc_readl(request);
-	value |= mask;
-	value &= ~IO_DPD_REQ_CODE_MASK;
-	value |= IO_DPD_REQ_CODE_ON;
-	tegra_pmc_writel(value, request);
+	tegra_pmc_writel(IO_DPD_REQ_CODE_ON | BIT(bit), request);
 
-	err = tegra_io_rail_poll(status, mask, mask, 250);
+	err = tegra_io_rail_poll(status, BIT(bit), BIT(bit), 250);
 	if (err)
 		goto error;
 

include/dt-bindings/mfd/stm32f4-rcc.h

+/*
+ * This header provides constants for the STM32F4 RCC IP
+ */
+
+#ifndef _DT_BINDINGS_MFD_STM32F4_RCC_H
+#define _DT_BINDINGS_MFD_STM32F4_RCC_H
+
+/* AHB1 */
+#define STM32F4_RCC_AHB1_GPIOA	0
+#define STM32F4_RCC_AHB1_GPIOB	1
+#define STM32F4_RCC_AHB1_GPIOC	2
+#define STM32F4_RCC_AHB1_GPIOD	3
+#define STM32F4_RCC_AHB1_GPIOE	4
+#define STM32F4_RCC_AHB1_GPIOF	5
+#define STM32F4_RCC_AHB1_GPIOG	6
+#define STM32F4_RCC_AHB1_GPIOH	7
+#define STM32F4_RCC_AHB1_GPIOI	8
+#define STM32F4_RCC_AHB1_GPIOJ	9
+#define STM32F4_RCC_AHB1_GPIOK	10
+#define STM32F4_RCC_AHB1_CRC	12
+#define STM32F4_RCC_AHB1_DMA1	21
+#define STM32F4_RCC_AHB1_DMA2	22
+#define STM32F4_RCC_AHB1_DMA2D	23
+#define STM32F4_RCC_AHB1_ETHMAC	25
+#define STM32F4_RCC_AHB1_OTGHS	29
+
+#define STM32F4_AHB1_RESET(bit) (STM32F4_RCC_AHB1_##bit + (0x10 * 8))
+#define STM32F4_AHB1_CLOCK(bit) (STM32F4_RCC_AHB1_##bit + (0x30 * 8))
+
+
+/* AHB2 */
+#define STM32F4_RCC_AHB2_DCMI	0
+#define STM32F4_RCC_AHB2_CRYP	4
+#define STM32F4_RCC_AHB2_HASH	5
+#define STM32F4_RCC_AHB2_RNG	6
+#define STM32F4_RCC_AHB2_OTGFS	7
+
+#define STM32F4_AHB2_RESET(bit)	(STM32F4_RCC_AHB2_##bit + (0x14 * 8))
+#define STM32F4_AHB2_CLOCK(bit)	(STM32F4_RCC_AHB2_##bit + (0x34 * 8))
+
+/* AHB3 */
+#define STM32F4_RCC_AHB3_FMC	0
+
+#define STM32F4_AHB3_RESET(bit)	(STM32F4_RCC_AHB3_##bit + (0x18 * 8))
+#define STM32F4_AHB3_CLOCK(bit)	(STM32F4_RCC_AHB3_##bit + (0x38 * 8))
+
+/* APB1 */
+#define STM32F4_RCC_APB1_TIM2	0
+#define STM32F4_RCC_APB1_TIM3	1
+#define STM32F4_RCC_APB1_TIM4	2
+#define STM32F4_RCC_APB1_TIM5	3
+#define STM32F4_RCC_APB1_TIM6	4
+#define STM32F4_RCC_APB1_TIM7	5
+#define STM32F4_RCC_APB1_TIM12	6
+#define STM32F4_RCC_APB1_TIM13	7
+#define STM32F4_RCC_APB1_TIM14	8
+#define STM32F4_RCC_APB1_WWDG	11
+#define STM32F4_RCC_APB1_SPI2	14
+#define STM32F4_RCC_APB1_SPI3	15
+#define STM32F4_RCC_APB1_UART2	17
+#define STM32F4_RCC_APB1_UART3	18
+#define STM32F4_RCC_APB1_UART4	19
+#define STM32F4_RCC_APB1_UART5	20
+#define STM32F4_RCC_APB1_I2C1	21
+#define STM32F4_RCC_APB1_I2C2	22
+#define STM32F4_RCC_APB1_I2C3	23
+#define STM32F4_RCC_APB1_CAN1	25
+#define STM32F4_RCC_APB1_CAN2	26
+#define STM32F4_RCC_APB1_PWR	28
+#define STM32F4_RCC_APB1_DAC	29
+#define STM32F4_RCC_APB1_UART7	30
+#define STM32F4_RCC_APB1_UART8	31
+
+#define STM32F4_APB1_RESET(bit)	(STM32F4_RCC_APB1_##bit + (0x20 * 8))
+#define STM32F4_APB1_CLOCK(bit)	(STM32F4_RCC_APB1_##bit + (0x40 * 8))
+
+/* APB2 */
+#define STM32F4_RCC_APB2_TIM1	0
+#define STM32F4_RCC_APB2_TIM8	1
+#define STM32F4_RCC_APB2_USART1	4
+#define STM32F4_RCC_APB2_USART6	5
+#define STM32F4_RCC_APB2_ADC	8
+#define STM32F4_RCC_APB2_SDIO	11
+#define STM32F4_RCC_APB2_SPI1	12
+#define STM32F4_RCC_APB2_SPI4	13
+#define STM32F4_RCC_APB2_SYSCFG	14
+#define STM32F4_RCC_APB2_TIM9	16
+#define STM32F4_RCC_APB2_TIM10	17
+#define STM32F4_RCC_APB2_TIM11	18
+#define STM32F4_RCC_APB2_SPI5	20
+#define STM32F4_RCC_APB2_SPI6	21
+#define STM32F4_RCC_APB2_SAI1	22
+#define STM32F4_RCC_APB2_LTDC	26
+
+#define STM32F4_APB2_RESET(bit)	(STM32F4_RCC_APB2_##bit + (0x24 * 8))
+#define STM32F4_APB2_CLOCK(bit)	(STM32F4_RCC_APB2_##bit + (0x44 * 8))
+
+#endif /* _DT_BINDINGS_MFD_STM32F4_RCC_H */

include/linux/firmware/meson/meson_sm.h

+/*
+ * Copyright (C) 2016 Endless Mobile, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _MESON_SM_FW_H_
+#define _MESON_SM_FW_H_
+
+enum {
+	SM_EFUSE_READ,
+	SM_EFUSE_WRITE,
+	SM_EFUSE_USER_MAX,
+};
+
+struct meson_sm_firmware;
+
+int meson_sm_call(unsigned int cmd_index, u32 *ret, u32 arg0, u32 arg1,
+		  u32 arg2, u32 arg3, u32 arg4);
+int meson_sm_call_write(void *buffer, unsigned int b_size, unsigned int cmd_index,
+			u32 arg0, u32 arg1, u32 arg2, u32 arg3, u32 arg4);
+int meson_sm_call_read(void *buffer, unsigned int cmd_index, u32 arg0, u32 arg1,
+		       u32 arg2, u32 arg3, u32 arg4);
+
+#endif /* _MESON_SM_FW_H_ */

include/linux/omap-gpmc.h

@@ -29,8 +29,8 @@ struct gpmc_nand_regs;
 struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs,
 					     int cs);
 #else
-static inline gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs,
-						    int cs)
+static inline struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs,
+							   int cs)
 {
 	return NULL;
 }

include/linux/soc/qcom/smd.h

@@ -55,11 +55,16 @@ void qcom_smd_driver_unregister(struct qcom_smd_driver *drv);
 struct qcom_smd_channel *qcom_smd_open_channel(struct qcom_smd_channel *channel,
 					       const char *name,
 					       qcom_smd_cb_t cb);
+void qcom_smd_close_channel(struct qcom_smd_channel *channel);
 void *qcom_smd_get_drvdata(struct qcom_smd_channel *channel);
 void qcom_smd_set_drvdata(struct qcom_smd_channel *channel, void *data);
 int qcom_smd_send(struct qcom_smd_channel *channel, const void *data, int len);
 
 
+struct qcom_smd_edge *qcom_smd_register_edge(struct device *parent,
+					     struct device_node *node);
+int qcom_smd_unregister_edge(struct qcom_smd_edge *edge);
+
 #else
 
 static inline int qcom_smd_driver_register(struct qcom_smd_driver *drv)
@@ -83,14 +88,20 @@ qcom_smd_open_channel(struct qcom_smd_channel *channel,
 	return NULL;
 }
 
-void *qcom_smd_get_drvdata(struct qcom_smd_channel *channel)
+static inline void qcom_smd_close_channel(struct qcom_smd_channel *channel)
+{
+	/* This shouldn't be possible */
+	WARN_ON(1);
+}
+
+static inline void *qcom_smd_get_drvdata(struct qcom_smd_channel *channel)
 {
 	/* This shouldn't be possible */
 	WARN_ON(1);
 	return NULL;
 }
 
-void qcom_smd_set_drvdata(struct qcom_smd_channel *channel, void *data)
+static inline void qcom_smd_set_drvdata(struct qcom_smd_channel *channel, void *data)
 {
 	/* This shouldn't be possible */
 	WARN_ON(1);
@@ -104,6 +115,20 @@ static inline int qcom_smd_send(struct qcom_smd_channel *channel,
 	return -ENXIO;
 }
 
+static inline struct qcom_smd_edge *
+qcom_smd_register_edge(struct device *parent,
+		       struct device_node *node)
+{
+	return ERR_PTR(-ENXIO);
+}
+
+static inline int qcom_smd_unregister_edge(struct qcom_smd_edge *edge)
+{
+	/* This shouldn't be possible */
+	WARN_ON(1);
+	return -ENXIO;
+}
+
 #endif
 
 #define module_qcom_smd_driver(__smd_driver) \