crypto: caam - add support for LS1021A

LS1021A is a QorIQ SoC having little endian CAAM.

There are a few differences b/w QorIQ and i.MX from CAAM perspective:

1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.

2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.

A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.

In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

drivers/crypto/caam/Kconfig

@@ -112,6 +112,14 @@ config CRYPTO_DEV_FSL_CAAM_RNG_API
 	  To compile this as a module, choose M here: the module
 	  will be called caamrng.
 
+config CRYPTO_DEV_FSL_CAAM_IMX
+	def_bool SOC_IMX6 || SOC_IMX7D
+	depends on CRYPTO_DEV_FSL_CAAM
+
+config CRYPTO_DEV_FSL_CAAM_LE
+	def_bool CRYPTO_DEV_FSL_CAAM_IMX || SOC_LS1021A
+	depends on CRYPTO_DEV_FSL_CAAM
+
 config CRYPTO_DEV_FSL_CAAM_DEBUG
 	bool "Enable debug output in CAAM driver"
 	depends on CRYPTO_DEV_FSL_CAAM

drivers/crypto/caam/ctrl.c

@@ -16,10 +16,10 @@
 #include "error.h"
 
 /*
- * ARM targets tend to have clock control subsystems that can
+ * i.MX targets tend to have clock control subsystems that can
  * enable/disable clocking to our device.
  */
-#ifdef CONFIG_ARM
+#ifdef CONFIG_CRYPTO_DEV_FSL_CAAM_IMX
 static inline struct clk *caam_drv_identify_clk(struct device *dev,
 						char *clk_name)
 {

drivers/crypto/caam/desc.h

@@ -23,12 +23,12 @@
 #define SEC4_SG_OFFS_MASK	0x00001fff
 
 struct sec4_sg_entry {
-#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
-	dma_addr_t ptr;
-#else
+#ifdef CONFIG_CRYPTO_DEV_FSL_CAAM_IMX
 	u32 rsvd1;
 	dma_addr_t ptr;
-#endif
+#else
+	u64 ptr;
+#endif /* CONFIG_CRYPTO_DEV_FSL_CAAM_IMX */
 	u32 len;
 	u8 rsvd2;
 	u8 buf_pool_id;

drivers/crypto/caam/regs.h

@@ -108,20 +108,31 @@
 
 /*
  * The only users of these wr/rd_reg64 functions is the Job Ring (JR).
- * The DMA address registers in the JR are a pair of 32-bit registers.
- * The layout is:
+ * The DMA address registers in the JR are handled differently depending on
+ * platform:
+ *
+ * 1. All BE CAAM platforms and i.MX platforms (LE CAAM):
  *
  *    base + 0x0000 : most-significant 32 bits
  *    base + 0x0004 : least-significant 32 bits
  *
  * The 32-bit version of this core therefore has to write to base + 0x0004
- * to set the 32-bit wide DMA address. This seems to be independent of the
- * endianness of the written/read data.
+ * to set the 32-bit wide DMA address.
+ *
+ * 2. All other LE CAAM platforms (LS1021A etc.)
+ *    base + 0x0000 : least-significant 32 bits
+ *    base + 0x0004 : most-significant 32 bits
  */
 
 #ifndef CONFIG_64BIT
+#if !defined(CONFIG_CRYPTO_DEV_FSL_CAAM_LE) || \
+	defined(CONFIG_CRYPTO_DEV_FSL_CAAM_IMX)
 #define REG64_MS32(reg) ((u32 __iomem *)(reg))
 #define REG64_LS32(reg) ((u32 __iomem *)(reg) + 1)
+#else
+#define REG64_MS32(reg) ((u32 __iomem *)(reg) + 1)
+#define REG64_LS32(reg) ((u32 __iomem *)(reg))
+#endif
 
 static inline void wr_reg64(u64 __iomem *reg, u64 data)
 {