Commit 6c7d826c authored by Magnus Damm's avatar Magnus Damm Committed by Paul Mundt

sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722

Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: default avatarMagnus Damm <damm@igel.co.jp>
Signed-off-by: default avatarPaul Mundt <lethal@linux-sh.org>
parent 9ca6ecac
......@@ -15,6 +15,7 @@
#include <linux/mtd/nand.h>
#include <linux/i2c.h>
#include <linux/smc91x.h>
#include <asm/clock.h>
#include <asm/machvec.h>
#include <asm/io.h>
#include <asm/sh_keysc.h>
......@@ -217,6 +218,8 @@ static struct i2c_board_info __initdata migor_i2c_devices[] = {
static int __init migor_devices_setup(void)
{
clk_always_enable("mstp214"); /* KEYSC */
i2c_register_board_info(0, migor_i2c_devices,
ARRAY_SIZE(migor_i2c_devices));
......@@ -235,16 +238,12 @@ static void __init migor_setup(char **cmdline_p)
ctrl_outw(ctrl_inw(PORT_PSELA) & ~0x4100, PORT_PSELA);
ctrl_outw(ctrl_inw(PORT_HIZCRA) & ~0x4000, PORT_HIZCRA);
ctrl_outw(ctrl_inw(PORT_HIZCRC) & ~0xc000, PORT_HIZCRC);
ctrl_outl(ctrl_inl(MSTPCR2) & ~0x00004000, MSTPCR2);
/* NAND Flash */
ctrl_outw(ctrl_inw(PORT_PXCR) & 0x0fff, PORT_PXCR);
ctrl_outl((ctrl_inl(BSC_CS6ABCR) & ~0x00000600) | 0x00000200,
BSC_CS6ABCR);
/* I2C */
ctrl_outl(ctrl_inl(MSTPCR1) & ~0x00000200, MSTPCR1);
/* Touch Panel - Enable IRQ6 */
ctrl_outw(ctrl_inw(PORT_PZCR) & ~0xc, PORT_PZCR);
ctrl_outw((ctrl_inw(PORT_PSELA) | 0x8000), PORT_PSELA);
......
......@@ -16,6 +16,7 @@
#include <linux/input.h>
#include <linux/smc91x.h>
#include <asm/machvec.h>
#include <asm/clock.h>
#include <asm/se7722.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
......@@ -145,6 +146,8 @@ static struct platform_device *se7722_devices[] __initdata = {
static int __init se7722_devices_setup(void)
{
clk_always_enable("mstp214"); /* KEYSC */
return platform_add_devices(se7722_devices,
ARRAY_SIZE(se7722_devices));
}
......@@ -154,11 +157,6 @@ static void __init se7722_setup(char **cmdline_p)
{
ctrl_outw(0x010D, FPGA_OUT); /* FPGA */
ctrl_outl(0x00051001, MSTPCR0);
ctrl_outl(0x00000000, MSTPCR1);
/* KEYSC, VOU, BEU, CEU, VEU, VPU, LCDC, USB */
ctrl_outl(0xffffb7c0, MSTPCR2);
ctrl_outw(0x0000, PORT_PECR); /* PORT E 1 = IRQ5 ,E 0 = BS */
ctrl_outw(0x1000, PORT_PJCR); /* PORT J 1 = IRQ1,J 0 =IRQ0 */
......
......@@ -13,6 +13,7 @@
#include <linux/serial_sci.h>
#include <linux/mm.h>
#include <linux/uio_driver.h>
#include <asm/clock.h>
#include <asm/mmzone.h>
static struct resource usbf_resources[] = {
......@@ -158,8 +159,21 @@ static struct platform_device *sh7722_devices[] __initdata = {
static int __init sh7722_devices_setup(void)
{
clk_always_enable("mstp031"); /* TLB */
clk_always_enable("mstp030"); /* IC */
clk_always_enable("mstp029"); /* OC */
clk_always_enable("mstp028"); /* URAM */
clk_always_enable("mstp026"); /* XYMEM */
clk_always_enable("mstp022"); /* INTC */
clk_always_enable("mstp020"); /* SuperHyway */
clk_always_enable("mstp109"); /* I2C */
clk_always_enable("mstp211"); /* USB */
clk_always_enable("mstp202"); /* VEU */
clk_always_enable("mstp201"); /* VPU */
platform_resource_setup_memory(&vpu_device, "vpu", 1 << 20);
platform_resource_setup_memory(&veu_device, "veu", 2 << 20);
return platform_add_devices(sh7722_devices,
ARRAY_SIZE(sh7722_devices));
}
......
......@@ -16,10 +16,6 @@
#include <asm/addrspace.h>
/* GPIO */
#define MSTPCR0 0xa4150030
#define MSTPCR1 0xa4150034
#define MSTPCR2 0xa4150038
#define PORT_PACR 0xa4050100
#define PORT_PDCR 0xa4050106
#define PORT_PECR 0xa4050108
......
......@@ -55,10 +55,6 @@
#define PA_LAN (PA_AREA6_IO + 0) /* SMC LAN91C111 */
/* GPIO */
#define MSTPCR0 0xA4150030UL
#define MSTPCR1 0xA4150034UL
#define MSTPCR2 0xA4150038UL
#define FPGA_IN 0xb1840000UL
#define FPGA_OUT 0xb1840004UL
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment