Merge git://git.kernel.org/pub/scm/linux/kernel/git/nico/orion into devel-stable

Documentation/DocBook/filesystems.tmpl

@@ -82,6 +82,11 @@
      </sect1>
   </chapter>
 
+  <chapter id="fs_events">
+     <title>Events based on file descriptors</title>
+!Efs/eventfd.c
+  </chapter>
+
   <chapter id="sysfs">
      <title>The Filesystem for Exporting Kernel Objects</title>
 !Efs/sysfs/file.c

Documentation/hwmon/jc42

@@ -51,7 +51,8 @@ Supported chips:
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f
-    Datasheet: -
+    Datasheet:
+	http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf
 
 Author:
 	Guenter Roeck <guenter.roeck@ericsson.com>
@@ -60,7 +61,11 @@ Author:
 Description
 -----------
 
-This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
+This driver implements support for JEDEC JC 42.4 compliant temperature sensors,
+which are used on many DDR3 memory modules for mobile devices and servers. Some
+systems use the sensor to prevent memory overheating by automatically throttling
+the memory controller.
+
 The driver auto-detects the chips listed above, but can be manually instantiated
 to support other JC 42.4 compliant chips.
 
@@ -81,15 +86,19 @@ limits. The chip supports only a single register to configure the hysteresis,
 which applies to all limits. This register can be written by writing into
 temp1_crit_hyst. Other hysteresis attributes are read-only.
 
+If the BIOS has configured the sensor for automatic temperature management, it
+is likely that it has locked the registers, i.e., that the temperature limits
+cannot be changed.
+
 Sysfs entries
 -------------
 
 temp1_input		Temperature (RO)
-temp1_min		Minimum temperature (RW)
-temp1_max		Maximum temperature (RW)
-temp1_crit		Critical high temperature (RW)
+temp1_min		Minimum temperature (RO or RW)
+temp1_max		Maximum temperature (RO or RW)
+temp1_crit		Critical high temperature (RO or RW)
 
-temp1_crit_hyst		Critical hysteresis temperature (RW)
+temp1_crit_hyst		Critical hysteresis temperature (RO or RW)
 temp1_max_hyst		Maximum hysteresis temperature (RO)
 
 temp1_min_alarm		Temperature low alarm

Documentation/hwmon/k10temp

@@ -9,6 +9,8 @@ Supported chips:
   Socket S1G3: Athlon II, Sempron, Turion II
 * AMD Family 11h processors:
   Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra)
+* AMD Family 12h processors: "Llano"
+* AMD Family 14h processors: "Brazos" (C/E/G-Series)
 
   Prefix: 'k10temp'
   Addresses scanned: PCI space
@@ -17,10 +19,14 @@ Supported chips:
     http://support.amd.com/us/Processor_TechDocs/31116.pdf
   BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors:
     http://support.amd.com/us/Processor_TechDocs/41256.pdf
+  BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors:
+    http://support.amd.com/us/Processor_TechDocs/43170.pdf
   Revision Guide for AMD Family 10h Processors:
     http://support.amd.com/us/Processor_TechDocs/41322.pdf
   Revision Guide for AMD Family 11h Processors:
     http://support.amd.com/us/Processor_TechDocs/41788.pdf
+  Revision Guide for AMD Family 14h Models 00h-0Fh Processors:
+    http://support.amd.com/us/Processor_TechDocs/47534.pdf
   AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks:
     http://support.amd.com/us/Processor_TechDocs/43373.pdf
   AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet:
@@ -34,7 +40,7 @@ Description
 -----------
 
 This driver permits reading of the internal temperature sensor of AMD
-Family 10h and 11h processors.
+Family 10h/11h/12h/14h processors.
 
 All these processors have a sensor, but on those for Socket F or AM2+,
 the sensor may return inconsistent values (erratum 319).  The driver

Documentation/kernel-parameters.txt

@@ -144,6 +144,11 @@ a fixed number of characters. This limit depends on the architecture
 and is between 256 and 4096 characters. It is defined in the file
 ./include/asm/setup.h as COMMAND_LINE_SIZE.
 
+Finally, the [KMG] suffix is commonly described after a number of kernel
+parameter values. These 'K', 'M', and 'G' letters represent the _binary_
+multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30
+bytes respectively. Such letter suffixes can also be entirely omitted.
+
 
 	acpi=		[HW,ACPI,X86]
 			Advanced Configuration and Power Interface
@@ -545,16 +550,20 @@ and is between 256 and 4096 characters. It is defined in the file
 			Format:
 			<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
 
-	crashkernel=nn[KMG]@ss[KMG]
-			[KNL] Reserve a chunk of physical memory to
-			hold a kernel to switch to with kexec on panic.
+	crashkernel=size[KMG][@offset[KMG]]
+			[KNL] Using kexec, Linux can switch to a 'crash kernel'
+			upon panic. This parameter reserves the physical
+			memory region [offset, offset + size] for that kernel
+			image. If '@offset' is omitted, then a suitable offset
+			is selected automatically. Check
+			Documentation/kdump/kdump.txt for further details.
 
 	crashkernel=range1:size1[,range2:size2,...][@offset]
 			[KNL] Same as above, but depends on the memory
 			in the running system. The syntax of range is
 			start-[end] where start and end are both
 			a memory unit (amount[KMG]). See also
-			Documentation/kdump/kdump.txt for a example.
+			Documentation/kdump/kdump.txt for an example.
 
 	cs89x0_dma=	[HW,NET]
 			Format: <dma>
@@ -1262,10 +1271,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			6 (KERN_INFO)		informational
 			7 (KERN_DEBUG)		debug-level messages
 
-	log_buf_len=n	Sets the size of the printk ring buffer, in bytes.
-			Format: { n | nk | nM }
-			n must be a power of two.  The default size
-			is set in the kernel config file.
+	log_buf_len=n[KMG]	Sets the size of the printk ring buffer,
+			in bytes.  n must be a power of two.  The default
+			size is set in the kernel config file.
 
 	logo.nologo	[FB] Disables display of the built-in Linux logo.
 			This may be used to provide more screen space for

MAINTAINERS

@@ -885,7 +885,7 @@ S:	Supported
 
 ARM/QUALCOMM MSM MACHINE SUPPORT
 M:	David Brown <davidb@codeaurora.org>
-M:	Daniel Walker <dwalker@codeaurora.org>
+M:	Daniel Walker <dwalker@fifo99.com>
 M:	Bryan Huntsman <bryanh@codeaurora.org>
 L:	linux-arm-msm@vger.kernel.org
 F:	arch/arm/mach-msm/
@@ -2873,7 +2873,6 @@ M:	Guenter Roeck <guenter.roeck@ericsson.com>
 L:	lm-sensors@lm-sensors.org
 W:	http://www.lm-sensors.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-hwmon/
-T:	quilt kernel.org/pub/linux/kernel/people/groeck/linux-staging/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging.git
 S:	Maintained
 F:	Documentation/hwmon/

Makefile

 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 38
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Flesh-Eating Bats with Fangs
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -1177,6 +1177,31 @@ config ARM_ERRATA_743622
 	  visible impact on the overall performance or power consumption of the
 	  processor.
 
+config ARM_ERRATA_751472
+	bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
+	depends on CPU_V7 && SMP
+	help
+	  This option enables the workaround for the 751472 Cortex-A9 (prior
+	  to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
+	  completion of a following broadcasted operation if the second
+	  operation is received by a CPU before the ICIALLUIS has completed,
+	  potentially leading to corrupted entries in the cache or TLB.
+
+config ARM_ERRATA_753970
+	bool "ARM errata: cache sync operation may be faulty"
+	depends on CACHE_PL310
+	help
+	  This option enables the workaround for the 753970 PL310 (r3p0) erratum.
+
+	  Under some condition the effect of cache sync operation on
+	  the store buffer still remains when the operation completes.
+	  This means that the store buffer is always asked to drain and
+	  this prevents it from merging any further writes. The workaround
+	  is to replace the normal offset of cache sync operation (0x730)
+	  by another offset targeting an unmapped PL310 register 0x740.
+	  This has the same effect as the cache sync operation: store buffer
+	  drain and waiting for all buffers empty.
+
 endmenu
 
 source "arch/arm/common/Kconfig"

arch/arm/Makefile

@@ -15,7 +15,7 @@ ifeq ($(CONFIG_CPU_ENDIAN_BE8),y)
 LDFLAGS_vmlinux	+= --be8
 endif
 
-OBJCOPYFLAGS	:=-O binary -R .note -R .note.gnu.build-id -R .comment -S
+OBJCOPYFLAGS	:=-O binary -R .comment -S
 GZFLAGS		:=-9
 #KBUILD_CFLAGS	+=-pipe
 # Explicitly specifiy 32-bit ARM ISA since toolchain default can be -mthumb:

arch/arm/boot/compressed/.gitignore

 font.c
-piggy.gz
+lib1funcs.S
+piggy.gzip
+piggy.lzo
+piggy.lzma
+vmlinux
 vmlinux.lds

arch/arm/configs/kirkwood_defconfig

@@ -24,6 +24,7 @@ CONFIG_MACH_OPENRD_ULTIMATE=y
 CONFIG_MACH_NETSPACE_V2=y
 CONFIG_MACH_INETSPACE_V2=y
 CONFIG_MACH_NETSPACE_MAX_V2=y
+CONFIG_MACH_D2NET_V2=y
 CONFIG_MACH_NET2BIG_V2=y
 CONFIG_MACH_NET5BIG_V2=y
 CONFIG_MACH_T5325=y

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -36,6 +36,7 @@
 #define L2X0_RAW_INTR_STAT		0x21C
 #define L2X0_INTR_CLEAR			0x220
 #define L2X0_CACHE_SYNC			0x730
+#define L2X0_DUMMY_REG			0x740
 #define L2X0_INV_LINE_PA		0x770
 #define L2X0_INV_WAY			0x77C
 #define L2X0_CLEAN_LINE_PA		0x7B0

arch/arm/include/asm/hardware/sp810.h

@@ -58,6 +58,9 @@
 
 static inline void sysctl_soft_reset(void __iomem *base)
 {
+	/* switch to slow mode */
+	writel(0x2, base + SCCTRL);
+
 	/* writing any value to SCSYSSTAT reg will reset system */
 	writel(0, base + SCSYSSTAT);
 }

arch/arm/include/asm/kexec.h

@@ -50,6 +50,9 @@ static inline void crash_setup_regs(struct pt_regs *newregs,
 	}
 }
 
+/* Function pointer to optional machine-specific reinitialization */
+extern void (*kexec_reinit)(void);
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* CONFIG_KEXEC */

arch/arm/include/asm/tlb.h

@@ -18,16 +18,34 @@
 #define __ASMARM_TLB_H
 
 #include <asm/cacheflush.h>
-#include <asm/tlbflush.h>
 
 #ifndef CONFIG_MMU
 
 #include <linux/pagemap.h>
+
+#define tlb_flush(tlb)	((void) tlb)
+
 #include <asm-generic/tlb.h>
 
 #else /* !CONFIG_MMU */
 
+#include <linux/swap.h>
 #include <asm/pgalloc.h>
+#include <asm/tlbflush.h>
+
+/*
+ * We need to delay page freeing for SMP as other CPUs can access pages
+ * which have been removed but not yet had their TLB entries invalidated.
+ * Also, as ARMv7 speculative prefetch can drag new entries into the TLB,
+ * we need to apply this same delaying tactic to ensure correct operation.
+ */
+#if defined(CONFIG_SMP) || defined(CONFIG_CPU_32v7)
+#define tlb_fast_mode(tlb)	0
+#define FREE_PTE_NR		500
+#else
+#define tlb_fast_mode(tlb)	1
+#define FREE_PTE_NR		0
+#endif
 
 /*
  * TLB handling.  This allows us to remove pages from the page
@@ -36,12 +54,58 @@
 struct mmu_gather {
 	struct mm_struct	*mm;
 	unsigned int		fullmm;
+	struct vm_area_struct	*vma;
 	unsigned long		range_start;
 	unsigned long		range_end;
+	unsigned int		nr;
+	struct page		*pages[FREE_PTE_NR];
 };
 
 DECLARE_PER_CPU(struct mmu_gather, mmu_gathers);
 
+/*
+ * This is unnecessarily complex.  There's three ways the TLB shootdown
+ * code is used:
+ *  1. Unmapping a range of vmas.  See zap_page_range(), unmap_region().
+ *     tlb->fullmm = 0, and tlb_start_vma/tlb_end_vma will be called.
+ *     tlb->vma will be non-NULL.
+ *  2. Unmapping all vmas.  See exit_mmap().
+ *     tlb->fullmm = 1, and tlb_start_vma/tlb_end_vma will be called.
+ *     tlb->vma will be non-NULL.  Additionally, page tables will be freed.
+ *  3. Unmapping argument pages.  See shift_arg_pages().
+ *     tlb->fullmm = 0, but tlb_start_vma/tlb_end_vma will not be called.
+ *     tlb->vma will be NULL.
+ */
+static inline void tlb_flush(struct mmu_gather *tlb)
+{
+	if (tlb->fullmm || !tlb->vma)
+		flush_tlb_mm(tlb->mm);
+	else if (tlb->range_end > 0) {
+		flush_tlb_range(tlb->vma, tlb->range_start, tlb->range_end);
+		tlb->range_start = TASK_SIZE;
+		tlb->range_end = 0;
+	}
+}
+
+static inline void tlb_add_flush(struct mmu_gather *tlb, unsigned long addr)
+{
+	if (!tlb->fullmm) {
+		if (addr < tlb->range_start)
+			tlb->range_start = addr;
+		if (addr + PAGE_SIZE > tlb->range_end)
+			tlb->range_end = addr + PAGE_SIZE;
+	}
+}
+
+static inline void tlb_flush_mmu(struct mmu_gather *tlb)
+{
+	tlb_flush(tlb);
+	if (!tlb_fast_mode(tlb)) {
+		free_pages_and_swap_cache(tlb->pages, tlb->nr);
+		tlb->nr = 0;
+	}
+}
+
 static inline struct mmu_gather *
 tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 {
@@ -49,6 +113,8 @@ tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 
 	tlb->mm = mm;
 	tlb->fullmm = full_mm_flush;
+	tlb->vma = NULL;
+	tlb->nr = 0;
 
 	return tlb;
 }
@@ -56,8 +122,7 @@ tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 static inline void
 tlb_finish_mmu(struct mmu_gather *tlb, unsigned long start, unsigned long end)
 {
-	if (tlb->fullmm)
-		flush_tlb_mm(tlb->mm);
+	tlb_flush_mmu(tlb);
 
 	/* keep the page table cache within bounds */
 	check_pgt_cache();
@@ -71,12 +136,7 @@ tlb_finish_mmu(struct mmu_gather *tlb, unsigned long start, unsigned long end)
 static inline void
 tlb_remove_tlb_entry(struct mmu_gather *tlb, pte_t *ptep, unsigned long addr)
 {
-	if (!tlb->fullmm) {
-		if (addr < tlb->range_start)
-			tlb->range_start = addr;
-		if (addr + PAGE_SIZE > tlb->range_end)
-			tlb->range_end = addr + PAGE_SIZE;
-	}
+	tlb_add_flush(tlb, addr);
 }
 
 /*
@@ -89,6 +149,7 @@ tlb_start_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 {
 	if (!tlb->fullmm) {
 		flush_cache_range(vma, vma->vm_start, vma->vm_end);
+		tlb->vma = vma;
 		tlb->range_start = TASK_SIZE;
 		tlb->range_end = 0;
 	}
@@ -97,12 +158,30 @@ tlb_start_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 static inline void
 tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 {
-	if (!tlb->fullmm && tlb->range_end > 0)
-		flush_tlb_range(vma, tlb->range_start, tlb->range_end);
+	if (!tlb->fullmm)
+		tlb_flush(tlb);
+}
+
+static inline void tlb_remove_page(struct mmu_gather *tlb, struct page *page)
+{
+	if (tlb_fast_mode(tlb)) {
+		free_page_and_swap_cache(page);
+	} else {
+		tlb->pages[tlb->nr++] = page;
+		if (tlb->nr >= FREE_PTE_NR)
+			tlb_flush_mmu(tlb);
+	}
+}
+
+static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte,
+	unsigned long addr)
+{
+	pgtable_page_dtor(pte);
+	tlb_add_flush(tlb, addr);
+	tlb_remove_page(tlb, pte);
 }
 
-#define tlb_remove_page(tlb,page)	free_page_and_swap_cache(page)
-#define pte_free_tlb(tlb, ptep, addr)	pte_free((tlb)->mm, ptep)
+#define pte_free_tlb(tlb, ptep, addr)	__pte_free_tlb(tlb, ptep, addr)
 #define pmd_free_tlb(tlb, pmdp, addr)	pmd_free((tlb)->mm, pmdp)
 
 #define tlb_migrate_finish(mm)		do { } while (0)

arch/arm/include/asm/tlbflush.h

@@ -10,12 +10,7 @@
 #ifndef _ASMARM_TLBFLUSH_H
 #define _ASMARM_TLBFLUSH_H
 
-
-#ifndef CONFIG_MMU
-
-#define tlb_flush(tlb)	((void) tlb)
-
-#else /* CONFIG_MMU */
+#ifdef CONFIG_MMU
 
 #include <asm/glue.h>
 

arch/arm/kernel/kprobes-decode.c

@@ -1437,7 +1437,7 @@ arm_kprobe_decode_insn(kprobe_opcode_t insn, struct arch_specific_insn *asi)
 
 		return space_cccc_1100_010x(insn, asi);
 
-	} else if ((insn & 0x0e000000) == 0x0c400000) {
+	} else if ((insn & 0x0e000000) == 0x0c000000) {
 
 		return space_cccc_110x(insn, asi);
 

arch/arm/kernel/machine_kexec.c

@@ -75,6 +75,11 @@ void machine_crash_shutdown(struct pt_regs *regs)
 	printk(KERN_INFO "Loading crashdump kernel...\n");
 }
 
+/*
+ * Function pointer to optional machine-specific reinitialization
+ */
+void (*kexec_reinit)(void);
+
 void machine_kexec(struct kimage *image)
 {
 	unsigned long page_list;
@@ -104,6 +109,8 @@ void machine_kexec(struct kimage *image)
 			   (unsigned long) reboot_code_buffer + KEXEC_CONTROL_PAGE_SIZE);
 	printk(KERN_INFO "Bye!\n");
 
+	if (kexec_reinit)
+		kexec_reinit();
 	local_irq_disable();
 	local_fiq_disable();
 	setup_mm_for_reboot(0); /* mode is not used, so just pass 0*/

arch/arm/kernel/pmu.c

@@ -97,28 +97,34 @@ set_irq_affinity(int irq,
 			   irq, cpu);
 	return err;
 #else
-	return 0;
+	return -EINVAL;
 #endif
 }
 
 static int
 init_cpu_pmu(void)
 {
-	int i, err = 0;
+	int i, irqs, err = 0;
 	struct platform_device *pdev = pmu_devices[ARM_PMU_DEVICE_CPU];
 
-	if (!pdev) {
-		err = -ENODEV;
-		goto out;
-	}
+	if (!pdev)
+		return -ENODEV;
+
+	irqs = pdev->num_resources;
+
+	/*
+	 * If we have a single PMU interrupt that we can't shift, assume that
+	 * we're running on a uniprocessor machine and continue.
+	 */
+	if (irqs == 1 && !irq_can_set_affinity(platform_get_irq(pdev, 0)))
+		return 0;
 
-	for (i = 0; i < pdev->num_resources; ++i) {
+	for (i = 0; i < irqs; ++i) {
 		err = set_irq_affinity(platform_get_irq(pdev, i), i);
 		if (err)
 			break;
 	}
 
-out:
 	return err;
 }
 

arch/arm/kernel/setup.c

@@ -226,8 +226,8 @@ int cpu_architecture(void)
 		 * Register 0 and check for VMSAv7 or PMSAv7 */
 		asm("mrc	p15, 0, %0, c0, c1, 4"
 		    : "=r" (mmfr0));
-		if ((mmfr0 & 0x0000000f) == 0x00000003 ||
-		    (mmfr0 & 0x000000f0) == 0x00000030)
+		if ((mmfr0 & 0x0000000f) >= 0x00000003 ||
+		    (mmfr0 & 0x000000f0) >= 0x00000030)
 			cpu_arch = CPU_ARCH_ARMv7;
 		else if ((mmfr0 & 0x0000000f) == 0x00000002 ||
 			 (mmfr0 & 0x000000f0) == 0x00000020)

arch/arm/kernel/signal.c

@@ -474,7 +474,9 @@ setup_return(struct pt_regs *regs, struct k_sigaction *ka,
 	unsigned long handler = (unsigned long)ka->sa.sa_handler;
 	unsigned long retcode;
 	int thumb = 0;
-	unsigned long cpsr = regs->ARM_cpsr & ~PSR_f;
+	unsigned long cpsr = regs->ARM_cpsr & ~(PSR_f | PSR_E_BIT);
+
+	cpsr |= PSR_ENDSTATE;
 
 	/*
 	 * Maybe we need to deliver a 32-bit signal to a 26-bit task.

arch/arm/kernel/vmlinux.lds.S

@@ -21,6 +21,12 @@
 #define ARM_CPU_KEEP(x)
 #endif
 
+#if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK)
+#define ARM_EXIT_KEEP(x)	x
+#else
+#define ARM_EXIT_KEEP(x)
+#endif
+
 OUTPUT_ARCH(arm)
 ENTRY(stext)
 
@@ -43,6 +49,7 @@ SECTIONS
 		_sinittext = .;
 			HEAD_TEXT
 			INIT_TEXT
+			ARM_EXIT_KEEP(EXIT_TEXT)
 		_einittext = .;
 		ARM_CPU_DISCARD(PROC_INFO)
 		__arch_info_begin = .;
@@ -67,6 +74,7 @@ SECTIONS
 #ifndef CONFIG_XIP_KERNEL
 		__init_begin = _stext;
 		INIT_DATA
+		ARM_EXIT_KEEP(EXIT_DATA)
 #endif
 	}
 
@@ -162,6 +170,7 @@ SECTIONS
 		. = ALIGN(PAGE_SIZE);
 		__init_begin = .;
 		INIT_DATA
+		ARM_EXIT_KEEP(EXIT_DATA)
 		. = ALIGN(PAGE_SIZE);
 		__init_end = .;
 #endif
@@ -247,6 +256,8 @@ SECTIONS
 	}
 #endif
 
+	NOTES
+
 	BSS_SECTION(0, 0, 0)
 	_end = .;
 

arch/arm/mach-dove/cm-a510.c

@@ -90,6 +90,7 @@ MACHINE_START(CM_A510, "Compulab CM-A510 Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= cm_a510_init,
 	.map_io		= dove_map_io,
+	.init_early	= dove_init_early,
 	.init_irq	= dove_init_irq,
 	.timer		= &dove_timer,
 MACHINE_END

arch/arm/mach-dove/common.c

@@ -532,6 +532,11 @@ void __init dove_i2c_init(void)
 /*****************************************************************************
  * Time handling
  ****************************************************************************/
+void __init dove_init_early(void)
+{
+	orion_time_set_base(TIMER_VIRT_BASE);
+}
+
 static int get_tclk(void)
 {
 	/* use DOVE_RESET_SAMPLE_HI/LO to detect tclk */
@@ -540,7 +545,8 @@ static int get_tclk(void)
 
 static void dove_timer_init(void)
 {
-	orion_time_init(IRQ_DOVE_BRIDGE, get_tclk());
+	orion_time_init(BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
+			IRQ_DOVE_BRIDGE, get_tclk());
 }
 
 struct sys_timer dove_timer = {

arch/arm/mach-dove/common.h

@@ -22,6 +22,7 @@ extern struct mbus_dram_target_info dove_mbus_dram_info;
  */
 void dove_map_io(void);
 void dove_init(void);
+void dove_init_early(void);
 void dove_init_irq(void);
 void dove_setup_cpu_mbus(void);
 void dove_ge00_init(struct mv643xx_eth_platform_data *eth_data);

arch/arm/mach-dove/dove-db-setup.c

@@ -97,6 +97,7 @@ MACHINE_START(DOVE_DB, "Marvell DB-MV88AP510-BP Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= dove_db_init,
 	.map_io		= dove_map_io,
+	.init_early	= dove_init_early,
 	.init_irq	= dove_init_irq,
 	.timer		= &dove_timer,
 MACHINE_END

arch/arm/mach-dove/include/mach/bridge-regs.h

@@ -26,10 +26,6 @@
 #define SYSTEM_SOFT_RESET	(BRIDGE_VIRT_BASE | 0x010c)
 #define  SOFT_RESET		0x00000001
 
-#define BRIDGE_CAUSE		(BRIDGE_VIRT_BASE | 0x0110)
-#define BRIDGE_MASK		(BRIDGE_VIRT_BASE | 0x0114)
-#define  BRIDGE_INT_TIMER0	0x0002
-#define  BRIDGE_INT_TIMER1	0x0004
 #define  BRIDGE_INT_TIMER1_CLR	(~0x0004)
 
 #define IRQ_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0200)

arch/arm/mach-dove/include/mach/dove.h

@@ -130,7 +130,8 @@
 #define DOVE_PMU_MPP_GENERAL_CTRL (DOVE_MPP_VIRT_BASE + 0x10)
 #define DOVE_RESET_SAMPLE_LO	(DOVE_MPP_VIRT_BASE | 0x014)
 #define DOVE_RESET_SAMPLE_HI	(DOVE_MPP_VIRT_BASE | 0x018)
-#define DOVE_GPIO_VIRT_BASE	(DOVE_SB_REGS_VIRT_BASE | 0xd0400)
+#define DOVE_GPIO_LO_VIRT_BASE	(DOVE_SB_REGS_VIRT_BASE | 0xd0400)
+#define DOVE_GPIO_HI_VIRT_BASE	(DOVE_SB_REGS_VIRT_BASE | 0xd0420)
 #define DOVE_GPIO2_VIRT_BASE    (DOVE_SB_REGS_VIRT_BASE | 0xe8400)
 #define DOVE_MPP_GENERAL_VIRT_BASE	(DOVE_SB_REGS_VIRT_BASE | 0xe803c)
 #define  DOVE_AU1_SPDIFO_GPIO_EN	(1 << 1)

arch/arm/mach-dove/include/mach/gpio.h

@@ -6,46 +6,4 @@
  * warranty of any kind, whether express or implied.
  */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <asm/errno.h>
-#include <mach/irqs.h>
 #include <plat/gpio.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define GPIO_MAX	72
-
-#define GPIO_BASE_LO		(DOVE_GPIO_VIRT_BASE + 0x00)
-#define GPIO_BASE_HI		(DOVE_GPIO_VIRT_BASE + 0x20)
-
-#define GPIO_BASE(pin)		((pin < 32) ? GPIO_BASE_LO :		\
-				 ((pin < 64) ? GPIO_BASE_HI :		\
-				  DOVE_GPIO2_VIRT_BASE))
-
-#define GPIO_OUT(pin)		(GPIO_BASE(pin) + 0x00)
-#define GPIO_IO_CONF(pin)	(GPIO_BASE(pin) + 0x04)
-#define GPIO_BLINK_EN(pin)	(GPIO_BASE(pin) + 0x08)
-#define GPIO_IN_POL(pin)	(GPIO_BASE(pin) + 0x0c)
-#define GPIO_DATA_IN(pin)	(GPIO_BASE(pin) + 0x10)
-#define GPIO_EDGE_CAUSE(pin)	(GPIO_BASE(pin) + 0x14)
-#define GPIO_EDGE_MASK(pin)	(GPIO_BASE(pin) + 0x18)
-#define GPIO_LEVEL_MASK(pin)	(GPIO_BASE(pin) + 0x1c)
-
-static inline int gpio_to_irq(int pin)
-{
-	if (pin < NR_GPIO_IRQS)
-		return pin + IRQ_DOVE_GPIO_START;
-
-	return -EINVAL;
-}
-
-static inline int irq_to_gpio(int irq)
-{
-	if (IRQ_DOVE_GPIO_START < irq && irq < NR_IRQS)
-		return irq - IRQ_DOVE_GPIO_START;
-
-	return -EINVAL;
-}
-
-#endif

arch/arm/mach-dove/include/mach/irqs.h

@@ -92,10 +92,5 @@
 
 #define NR_IRQS			(IRQ_DOVE_PMU_START + NR_PMU_IRQS)
 
-/* Required for compatability with PXA AC97 driver.	*/
-#define IRQ_AC97		IRQ_DOVE_AC97
-/* Required for compatability with PXA DMA driver.	*/
-#define IRQ_DMA			IRQ_DOVE_PDMA
-/* Required for compatability with PXA NAND driver 	*/
-#define IRQ_NAND		IRQ_DOVE_NAND
+
 #endif

arch/arm/mach-dove/irq.c

@@ -99,11 +99,21 @@ void __init dove_init_irq(void)
 	orion_irq_init(32, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF));
 
 	/*
-	 * Mask and clear GPIO IRQ interrupts.
+	 * Initialize gpiolib for GPIOs 0-71.
 	 */
-	writel(0, GPIO_LEVEL_MASK(0));
-	writel(0, GPIO_EDGE_MASK(0));
-	writel(0, GPIO_EDGE_CAUSE(0));
+	orion_gpio_init(0, 32, DOVE_GPIO_LO_VIRT_BASE, 0,
+			IRQ_DOVE_GPIO_START);
+	set_irq_chained_handler(IRQ_DOVE_GPIO_0_7, gpio_irq_handler);
+	set_irq_chained_handler(IRQ_DOVE_GPIO_8_15, gpio_irq_handler);
+	set_irq_chained_handler(IRQ_DOVE_GPIO_16_23, gpio_irq_handler);
+	set_irq_chained_handler(IRQ_DOVE_GPIO_24_31, gpio_irq_handler);
+
+	orion_gpio_init(32, 32, DOVE_GPIO_HI_VIRT_BASE, 0,
+			IRQ_DOVE_GPIO_START + 32);
+	set_irq_chained_handler(IRQ_DOVE_HIGH_GPIO, gpio_irq_handler);
+
+	orion_gpio_init(64, 8, DOVE_GPIO2_VIRT_BASE, 0,
+			IRQ_DOVE_GPIO_START + 64);
 
 	/*
 	 * Mask and clear PMU interrupts
@@ -111,18 +121,6 @@ void __init dove_init_irq(void)
 	writel(0, PMU_INTERRUPT_MASK);
 	writel(0, PMU_INTERRUPT_CAUSE);
 
-	for (i = IRQ_DOVE_GPIO_START; i < IRQ_DOVE_PMU_START; i++) {
-		set_irq_chip(i, &orion_gpio_irq_chip);
-		set_irq_handler(i, handle_level_irq);
-		irq_desc[i].status |= IRQ_LEVEL;
-		set_irq_flags(i, IRQF_VALID);
-	}
-	set_irq_chained_handler(IRQ_DOVE_GPIO_0_7, gpio_irq_handler);
-	set_irq_chained_handler(IRQ_DOVE_GPIO_8_15, gpio_irq_handler);
-	set_irq_chained_handler(IRQ_DOVE_GPIO_16_23, gpio_irq_handler);
-	set_irq_chained_handler(IRQ_DOVE_GPIO_24_31, gpio_irq_handler);
-	set_irq_chained_handler(IRQ_DOVE_HIGH_GPIO, gpio_irq_handler);
-
 	for (i = IRQ_DOVE_PMU_START; i < NR_IRQS; i++) {
 		set_irq_chip(i, &pmu_irq_chip);
 		set_irq_handler(i, handle_level_irq);

arch/arm/mach-kirkwood/common.c

@@ -21,6 +21,7 @@
 #include <net/dsa.h>
 #include <asm/page.h>
 #include <asm/timex.h>
+#include <asm/kexec.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 #include <mach/kirkwood.h>
@@ -846,9 +847,14 @@ static void __init kirkwood_wdt_init(void)
 /*****************************************************************************
  * Time handling
  ****************************************************************************/
+void __init kirkwood_init_early(void)
+{
+	orion_time_set_base(TIMER_VIRT_BASE);
+}
+
 int kirkwood_tclk;
 
-int __init kirkwood_find_tclk(void)
+static int __init kirkwood_find_tclk(void)
 {
 	u32 dev, rev;
 
@@ -864,7 +870,9 @@ int __init kirkwood_find_tclk(void)
 static void __init kirkwood_timer_init(void)
 {
 	kirkwood_tclk = kirkwood_find_tclk();
-	orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
+
+	orion_time_init(BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
+			IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
 }
 
 struct sys_timer kirkwood_timer = {
@@ -1003,6 +1011,10 @@ void __init kirkwood_init(void)
 	kirkwood_xor0_init();
 	kirkwood_xor1_init();
 	kirkwood_crypto_init();
+
+#ifdef CONFIG_KEXEC 
+	kexec_reinit = kirkwood_enable_pcie;
+#endif
 }
 
 static int __init kirkwood_clock_gate(void)

arch/arm/mach-kirkwood/common.h

@@ -27,11 +27,13 @@ struct kirkwood_asoc_platform_data;
  */
 void kirkwood_map_io(void);
 void kirkwood_init(void);
+void kirkwood_init_early(void);
 void kirkwood_init_irq(void);
 
 extern struct mbus_dram_target_info kirkwood_mbus_dram_info;
 void kirkwood_setup_cpu_mbus(void);
 
+void kirkwood_enable_pcie(void);
 void kirkwood_pcie_id(u32 *dev, u32 *rev);
 
 void kirkwood_ehci_init(void);

arch/arm/mach-kirkwood/d2net_v2-setup.c

@@ -224,6 +224,7 @@ MACHINE_START(D2NET_V2, "LaCie d2 Network v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= d2net_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/db88f6281-bp-setup.c

@@ -100,6 +100,7 @@ MACHINE_START(DB88F6281_BP, "Marvell DB-88F6281-BP Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= db88f6281_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/dockstar-setup.c

@@ -105,6 +105,7 @@ MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar")
 	.boot_params	= 0x00000100,
 	.init_machine	= dockstar_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/guruplug-setup.c

@@ -124,6 +124,7 @@ MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= guruplug_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -29,9 +29,6 @@
 #define BRIDGE_CAUSE		(BRIDGE_VIRT_BASE | 0x0110)
 #define WDT_INT_REQ		0x0008
 
-#define BRIDGE_MASK		(BRIDGE_VIRT_BASE | 0x0114)
-#define BRIDGE_INT_TIMER0	0x0002
-#define BRIDGE_INT_TIMER1	0x0004
 #define BRIDGE_INT_TIMER1_CLR	(~0x0004)
 
 #define IRQ_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0200)

arch/arm/mach-kirkwood/include/mach/gpio.h

@@ -6,33 +6,4 @@
  * warranty of any kind, whether express or implied.
  */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <mach/irqs.h>
 #include <plat/gpio.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define GPIO_MAX		50
-#define GPIO_OFF(pin)		(((pin) >> 5) ? 0x0140 : 0x0100)
-#define GPIO_OUT(pin)		(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x00)
-#define GPIO_IO_CONF(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x04)
-#define GPIO_BLINK_EN(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x08)
-#define GPIO_IN_POL(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x0c)
-#define GPIO_DATA_IN(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x10)
-#define GPIO_EDGE_CAUSE(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x14)
-#define GPIO_EDGE_MASK(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x18)
-#define GPIO_LEVEL_MASK(pin)	(DEV_BUS_VIRT_BASE + GPIO_OFF(pin) + 0x1c)
-
-static inline int gpio_to_irq(int pin)
-{
-	return pin + IRQ_KIRKWOOD_GPIO_START;
-}
-
-static inline int irq_to_gpio(int irq)
-{
-	return irq - IRQ_KIRKWOOD_GPIO_START;
-}
-
-
-#endif

arch/arm/mach-kirkwood/include/mach/kirkwood.h

@@ -69,6 +69,8 @@
 #define DEV_BUS_VIRT_BASE	(KIRKWOOD_REGS_VIRT_BASE | 0x10000)
 #define  SAMPLE_AT_RESET	(DEV_BUS_VIRT_BASE | 0x0030)
 #define  DEVICE_ID		(DEV_BUS_VIRT_BASE | 0x0034)
+#define  GPIO_LOW_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x0100)
+#define  GPIO_HIGH_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x0140)
 #define  RTC_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x0300)
 #define  SPI_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x0600)
 #define  I2C_PHYS_BASE		(DEV_BUS_PHYS_BASE | 0x1000)

arch/arm/mach-kirkwood/irq.c

@@ -27,31 +27,21 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 
 void __init kirkwood_init_irq(void)
 {
-	int i;
-
 	orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF));
 	orion_irq_init(32, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF));
 
 	/*
-	 * Mask and clear GPIO IRQ interrupts.
+	 * Initialize gpiolib for GPIOs 0-49.
 	 */
-	writel(0, GPIO_LEVEL_MASK(0));
-	writel(0, GPIO_EDGE_MASK(0));
-	writel(0, GPIO_EDGE_CAUSE(0));
-	writel(0, GPIO_LEVEL_MASK(32));
-	writel(0, GPIO_EDGE_MASK(32));
-	writel(0, GPIO_EDGE_CAUSE(32));
-
-	for (i = IRQ_KIRKWOOD_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_chip);
-		set_irq_handler(i, handle_level_irq);
-		irq_desc[i].status |= IRQ_LEVEL;
-		set_irq_flags(i, IRQF_VALID);
-	}
+	orion_gpio_init(0, 32, GPIO_LOW_VIRT_BASE, 0,
+			IRQ_KIRKWOOD_GPIO_START);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_LOW_0_7, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_LOW_8_15, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_LOW_16_23, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_LOW_24_31, gpio_irq_handler);
+
+	orion_gpio_init(32, 18, GPIO_HIGH_VIRT_BASE, 0,
+			IRQ_KIRKWOOD_GPIO_START + 32);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_HIGH_0_7, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_HIGH_8_15, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_KIRKWOOD_GPIO_HIGH_16_23, gpio_irq_handler);

arch/arm/mach-kirkwood/mpp.c

@@ -49,9 +49,6 @@ void __init kirkwood_mpp_conf(unsigned int *mpp_list)
 	if (!variant_mask)
 		return;
 
-	/* Initialize gpiolib. */
-	orion_gpio_init();
-
 	printk(KERN_DEBUG "initial MPP regs:");
 	for (i = 0; i < MPP_NR_REGS; i++) {
 		mpp_ctrl[i] = readl(MPP_CTRL(i));

arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c

@@ -166,6 +166,7 @@ MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= mv88f6281gtw_ge_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/netspace_v2-setup.c

@@ -261,6 +261,7 @@ MACHINE_START(NETSPACE_V2, "LaCie Network Space v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -271,6 +272,7 @@ MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -281,6 +283,7 @@ MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= netspace_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/netxbig_v2-setup.c

@@ -402,6 +402,7 @@ MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -412,6 +413,7 @@ MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= netxbig_v2_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/openrd-setup.c

@@ -217,6 +217,7 @@ MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -228,6 +229,7 @@ MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -239,6 +241,7 @@ MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= openrd_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/pcie.c

@@ -18,8 +18,16 @@
 #include <mach/bridge-regs.h>
 #include "common.h"
 
+void kirkwood_enable_pcie(void)
+{
+	u32 curr = readl(CLOCK_GATING_CTRL);
+	if (!(curr & CGC_PEX0))
+		writel(curr | CGC_PEX0, CLOCK_GATING_CTRL);
+}
+
 void __init kirkwood_pcie_id(u32 *dev, u32 *rev)
 {
+	kirkwood_enable_pcie();
 	*dev = orion_pcie_dev_id((void __iomem *)PCIE_VIRT_BASE);
 	*rev = orion_pcie_rev((void __iomem *)PCIE_VIRT_BASE);
 }

arch/arm/mach-kirkwood/rd88f6192-nas-setup.c

@@ -82,6 +82,7 @@ MACHINE_START(RD88F6192_NAS, "Marvell RD-88F6192-NAS Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f6192_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/rd88f6281-setup.c

@@ -118,6 +118,7 @@ MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f6281_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/sheevaplug-setup.c

@@ -134,6 +134,7 @@ MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= sheevaplug_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
@@ -144,6 +145,7 @@ MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= sheevaplug_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/t5325-setup.c

@@ -23,6 +23,7 @@
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
+#include <sound/alc5623.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/kirkwood.h>
@@ -134,6 +135,7 @@ static unsigned int hp_t5325_mpp_config[] __initdata = {
 	MPP33_GE1_TXCTL,
 	MPP39_AU_I2SBCLK,
 	MPP40_AU_I2SDO,
+	MPP43_AU_I2SDI,
 	MPP41_AU_I2SLRCLK,
 	MPP42_AU_I2SMCLK,
 	MPP45_GPIO,		/* Power button */
@@ -141,6 +143,18 @@ static unsigned int hp_t5325_mpp_config[] __initdata = {
 	0
 };
 
+static struct alc5623_platform_data alc5621_data = {
+	.add_ctrl = 0x3700,
+	.jack_det_ctrl = 0x4810,
+};
+
+static struct i2c_board_info i2c_board_info[] __initdata = {
+	{
+		I2C_BOARD_INFO("alc5621", 0x1a),
+		.platform_data = &alc5621_data,
+	},
+};
+
 #define HP_T5325_GPIO_POWER_OFF		48
 
 static void hp_t5325_power_off(void)
@@ -166,6 +180,9 @@ static void __init hp_t5325_init(void)
 	kirkwood_ehci_init();
 	platform_device_register(&hp_t5325_button_device);
 
+	i2c_register_board_info(0, i2c_board_info, ARRAY_SIZE(i2c_board_info));
+	kirkwood_audio_init();
+
 	if (gpio_request(HP_T5325_GPIO_POWER_OFF, "power-off") == 0 &&
 	    gpio_direction_output(HP_T5325_GPIO_POWER_OFF, 0) == 0)
 		pm_power_off = hp_t5325_power_off;
@@ -187,6 +204,7 @@ MACHINE_START(T5325, "HP t5325 Thin Client")
 	.boot_params	= 0x00000100,
 	.init_machine	= hp_t5325_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/ts219-setup.c

@@ -135,6 +135,7 @@ MACHINE_START(TS219, "QNAP TS-119/TS-219")
 	.boot_params	= 0x00000100,
 	.init_machine	= qnap_ts219_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-kirkwood/ts41x-setup.c

@@ -154,6 +154,8 @@ static void __init qnap_ts41x_init(void)
 static int __init ts41x_pci_init(void)
 {
 	if (machine_is_ts41x()) {
+		u32 dev, rev;
+
 		/*
 		 * Without this explicit reset, the PCIe SATA controller
 		 * (Marvell 88sx7042/sata_mv) is known to stop working
@@ -161,7 +163,11 @@ static int __init ts41x_pci_init(void)
 		 */
 		orion_pcie_reset((void __iomem *)PCIE_VIRT_BASE);
 
-		kirkwood_pcie_init(KW_PCIE0);
+		kirkwood_pcie_id(&dev, &rev);
+		if (dev == MV88F6282_DEV_ID)
+			kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
+		else
+			kirkwood_pcie_init(KW_PCIE0);
 	}
 
    return 0;
@@ -173,6 +179,7 @@ MACHINE_START(TS41X, "QNAP TS-41x")
 	.boot_params	= 0x00000100,
 	.init_machine	= qnap_ts41x_init,
 	.map_io		= kirkwood_map_io,
+	.init_early	= kirkwood_init_early,
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END

arch/arm/mach-loki/common.c

@@ -18,6 +18,7 @@
 #include <asm/timex.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
+#include <mach/bridge-regs.h>
 #include <mach/loki.h>
 #include <plat/orion_nand.h>
 #include <plat/time.h>
@@ -290,9 +291,15 @@ void __init loki_uart1_init(void)
 /*****************************************************************************
  * Time handling
  ****************************************************************************/
+void __init loki_init_early(void)
+{
+	orion_time_set_base(TIMER_VIRT_BASE);
+}
+
 static void loki_timer_init(void)
 {
-	orion_time_init(IRQ_LOKI_BRIDGE, LOKI_TCLK);
+	orion_time_init(BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
+			IRQ_LOKI_BRIDGE, LOKI_TCLK);
 }
 
 struct sys_timer loki_timer = {

arch/arm/mach-loki/common.h

@@ -18,6 +18,7 @@ struct mv643xx_eth_platform_data;
  */
 void loki_map_io(void);
 void loki_init(void);
+void loki_init_early(void);
 void loki_init_irq(void);
 
 extern struct mbus_dram_target_info loki_mbus_dram_info;

arch/arm/mach-loki/include/mach/bridge-regs.h

@@ -17,11 +17,6 @@
 #define SYSTEM_SOFT_RESET	(BRIDGE_VIRT_BASE | 0x010c)
 #define SOFT_RESET		0x00000001
 
-#define BRIDGE_CAUSE		(BRIDGE_VIRT_BASE | 0x0110)
-
-#define BRIDGE_MASK		(BRIDGE_VIRT_BASE | 0x0114)
-#define BRIDGE_INT_TIMER0	0x0002
-#define BRIDGE_INT_TIMER1	0x0004
 #define BRIDGE_INT_TIMER1_CLR	0x0004
 
 #define IRQ_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0200)

arch/arm/mach-loki/lb88rc8480-setup.c

@@ -93,6 +93,7 @@ MACHINE_START(LB88RC8480, "Marvell LB88RC8480 Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= lb88rc8480_init,
 	.map_io		= loki_map_io,
+	.init_early	= loki_init_early,
 	.init_irq	= loki_init_irq,
 	.timer		= &loki_timer,
 MACHINE_END

arch/arm/mach-mv78xx0/buffalo-wxl-setup.c

@@ -148,6 +148,7 @@ MACHINE_START(TERASTATION_WXL, "Buffalo Nas WXL")
 	.boot_params	= 0x00000100,
 	.init_machine	= wxl_init,
 	.map_io		= mv78xx0_map_io,
+	.init_early	= mv78xx0_init_early,
 	.init_irq	= mv78xx0_init_irq,
 	.timer		= &mv78xx0_timer,
 MACHINE_END

arch/arm/mach-mv78xx0/common.c

@@ -818,9 +818,15 @@ void __init mv78xx0_uart3_init(void)
 /*****************************************************************************
  * Time handling
  ****************************************************************************/
+void __init mv78xx0_init_early(void)
+{
+	orion_time_set_base(TIMER_VIRT_BASE);
+}
+
 static void mv78xx0_timer_init(void)
 {
-	orion_time_init(IRQ_MV78XX0_TIMER_1, get_tclk());
+	orion_time_init(BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
+			IRQ_MV78XX0_TIMER_1, get_tclk());
 }
 
 struct sys_timer mv78xx0_timer = {

arch/arm/mach-mv78xx0/common.h

@@ -20,6 +20,7 @@ struct mv_sata_platform_data;
 int mv78xx0_core_index(void);
 void mv78xx0_map_io(void);
 void mv78xx0_init(void);
+void mv78xx0_init_early(void);
 void mv78xx0_init_irq(void);
 
 extern struct mbus_dram_target_info mv78xx0_mbus_dram_info;

arch/arm/mach-mv78xx0/db78x00-bp-setup.c

@@ -96,6 +96,7 @@ MACHINE_START(DB78X00_BP, "Marvell DB-78x00-BP Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= db78x00_init,
 	.map_io		= mv78xx0_map_io,
+	.init_early	= mv78xx0_init_early,
 	.init_irq	= mv78xx0_init_irq,
 	.timer		= &mv78xx0_timer,
 MACHINE_END

arch/arm/mach-mv78xx0/include/mach/bridge-regs.h

@@ -20,10 +20,6 @@
 #define SYSTEM_SOFT_RESET	(BRIDGE_VIRT_BASE | 0x010c)
 #define SOFT_RESET		0x00000001
 
-#define BRIDGE_CAUSE		(BRIDGE_VIRT_BASE | 0x0110)
-#define BRIDGE_MASK		(BRIDGE_VIRT_BASE | 0x0114)
-#define BRIDGE_INT_TIMER0	0x0002
-#define BRIDGE_INT_TIMER1	0x0004
 #define BRIDGE_INT_TIMER1_CLR	(~0x0004)
 
 #define IRQ_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0200)

arch/arm/mach-mv78xx0/include/mach/gpio.h

@@ -6,35 +6,4 @@
  * warranty of any kind, whether express or implied.
  */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <mach/irqs.h>
 #include <plat/gpio.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-extern int mv78xx0_core_index(void);
-
-#define GPIO_MAX		32
-#define GPIO_OUT(pin)		(DEV_BUS_VIRT_BASE + 0x0100)
-#define GPIO_IO_CONF(pin)	(DEV_BUS_VIRT_BASE + 0x0104)
-#define GPIO_BLINK_EN(pin)	(DEV_BUS_VIRT_BASE + 0x0108)
-#define GPIO_IN_POL(pin)	(DEV_BUS_VIRT_BASE + 0x010c)
-#define GPIO_DATA_IN(pin)	(DEV_BUS_VIRT_BASE + 0x0110)
-#define GPIO_EDGE_CAUSE(pin)	(DEV_BUS_VIRT_BASE + 0x0114)
-#define GPIO_MASK_OFF		(mv78xx0_core_index() ? 0x18 : 0)
-#define GPIO_EDGE_MASK(pin)	(DEV_BUS_VIRT_BASE + 0x0118 + GPIO_MASK_OFF)
-#define GPIO_LEVEL_MASK(pin)	(DEV_BUS_VIRT_BASE + 0x011c + GPIO_MASK_OFF)
-
-static inline int gpio_to_irq(int pin)
-{
-	return pin + IRQ_MV78XX0_GPIO_START;
-}
-
-static inline int irq_to_gpio(int irq)
-{
-	return irq - IRQ_MV78XX0_GPIO_START;
-}
-
-
-#endif

arch/arm/mach-mv78xx0/include/mach/mv78xx0.h

@@ -71,6 +71,7 @@
 #define DEV_BUS_VIRT_BASE	(MV78XX0_REGS_VIRT_BASE | 0x10000)
 #define  SAMPLE_AT_RESET_LOW	(DEV_BUS_VIRT_BASE | 0x0030)
 #define  SAMPLE_AT_RESET_HIGH	(DEV_BUS_VIRT_BASE | 0x0034)
+#define  GPIO_VIRT_BASE		(DEV_BUS_VIRT_BASE | 0x0100)
 #define  I2C_0_PHYS_BASE	(DEV_BUS_PHYS_BASE | 0x1000)
 #define  I2C_1_PHYS_BASE	(DEV_BUS_PHYS_BASE | 0x1100)
 #define  UART0_PHYS_BASE	(DEV_BUS_PHYS_BASE | 0x2000)

arch/arm/mach-mv78xx0/irq.c

@@ -26,28 +26,18 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 
 void __init mv78xx0_init_irq(void)
 {
-	int i;
-
-	/* Initialize gpiolib. */
-	orion_gpio_init();
-
 	orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF));
 	orion_irq_init(32, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF));
 	orion_irq_init(64, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_ERR_OFF));
 
 	/*
-	 * Mask and clear GPIO IRQ interrupts.
+	 * Initialize gpiolib for GPIOs 0-31.  (The GPIO interrupt mask
+	 * registers for core #1 are at an offset of 0x18 from those of
+	 * core #0.)
 	 */
-	writel(0, GPIO_LEVEL_MASK(0));
-	writel(0, GPIO_EDGE_MASK(0));
-	writel(0, GPIO_EDGE_CAUSE(0));
-
-	for (i = IRQ_MV78XX0_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_chip);
-		set_irq_handler(i, handle_level_irq);
-		irq_desc[i].status |= IRQ_LEVEL;
-		set_irq_flags(i, IRQF_VALID);
-	}
+	orion_gpio_init(0, 32, GPIO_VIRT_BASE,
+			mv78xx0_core_index() ? 0x18 : 0,
+			IRQ_MV78XX0_GPIO_START);
 	set_irq_chained_handler(IRQ_MV78XX0_GPIO_0_7, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_MV78XX0_GPIO_8_15, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_MV78XX0_GPIO_16_23, gpio_irq_handler);

arch/arm/mach-mv78xx0/mpp.c

@@ -44,9 +44,6 @@ void __init mv78xx0_mpp_conf(unsigned int *mpp_list)
 	if (!variant_mask)
 		return;
 
-	/* Initialize gpiolib. */
-	orion_gpio_init();
-
 	printk(KERN_DEBUG "initial MPP regs:");
 	for (i = 0; i < MPP_NR_REGS; i++) {
 		mpp_ctrl[i] = readl(MPP_CTRL(i));

arch/arm/mach-mv78xx0/rd78x00-masa-setup.c

@@ -81,6 +81,7 @@ MACHINE_START(RD78X00_MASA, "Marvell RD-78x00-MASA Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd78x00_masa_init,
 	.map_io		= mv78xx0_map_io,
+	.init_early	= mv78xx0_init_early,
 	.init_irq	= mv78xx0_init_irq,
 	.timer		= &mv78xx0_timer,
 MACHINE_END

arch/arm/mach-orion5x/common.c

@@ -26,6 +26,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
+#include <mach/bridge-regs.h>
 #include <mach/hardware.h>
 #include <mach/orion5x.h>
 #include <plat/ehci-orion.h>
@@ -599,6 +600,11 @@ void __init orion5x_wdt_init(void)
 /*****************************************************************************
  * Time handling
  ****************************************************************************/
+void __init orion5x_init_early(void)
+{
+	orion_time_set_base(TIMER_VIRT_BASE);
+}
+
 int orion5x_tclk;
 
 int __init orion5x_find_tclk(void)
@@ -616,7 +622,9 @@ int __init orion5x_find_tclk(void)
 static void orion5x_timer_init(void)
 {
 	orion5x_tclk = orion5x_find_tclk();
-	orion_time_init(IRQ_ORION5X_BRIDGE, orion5x_tclk);
+
+	orion_time_init(ORION5X_BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
+			IRQ_ORION5X_BRIDGE, orion5x_tclk);
 }
 
 struct sys_timer orion5x_timer = {

arch/arm/mach-orion5x/common.h

@@ -9,6 +9,7 @@ struct mv_sata_platform_data;
  * Basic Orion init functions used early by machine-setup.
  */
 void orion5x_map_io(void);
+void orion5x_init_early(void);
 void orion5x_init_irq(void);
 void orion5x_init(void);
 extern int orion5x_tclk;

arch/arm/mach-orion5x/d2net-setup.c

@@ -339,6 +339,7 @@ MACHINE_START(D2NET, "LaCie d2 Network")
 	.boot_params	= 0x00000100,
 	.init_machine	= d2net_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,
@@ -350,6 +351,7 @@ MACHINE_START(BIGDISK, "LaCie Big Disk Network")
 	.boot_params	= 0x00000100,
 	.init_machine	= d2net_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/db88f5281-setup.c

@@ -361,6 +361,7 @@ MACHINE_START(DB88F5281, "Marvell Orion-2 Development Board")
 	.boot_params	= 0x00000100,
 	.init_machine	= db88f5281_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 MACHINE_END

arch/arm/mach-orion5x/dns323-setup.c

@@ -733,6 +733,7 @@ MACHINE_START(DNS323, "D-Link DNS-323")
 	.boot_params	= 0x00000100,
 	.init_machine	= dns323_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/edmini_v2-setup.c

@@ -254,6 +254,7 @@ MACHINE_START(EDMINI_V2, "LaCie Ethernet Disk mini V2")
 	.boot_params	= 0x00000100,
 	.init_machine	= edmini_v2_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/include/mach/bridge-regs.h

@@ -22,14 +22,12 @@
 
 #define CPU_SOFT_RESET		(ORION5X_BRIDGE_VIRT_BASE | 0x10c)
 
+#define BRIDGE_CAUSE		(ORION5X_BRIDGE_VIRT_BASE | 0x110)
+
 #define POWER_MNG_CTRL_REG	(ORION5X_BRIDGE_VIRT_BASE | 0x11C)
 
-#define BRIDGE_CAUSE		(ORION5X_BRIDGE_VIRT_BASE | 0x110)
 #define WDT_INT_REQ		0x0008
 
-#define BRIDGE_MASK		(ORION5X_BRIDGE_VIRT_BASE | 0x114)
-#define BRIDGE_INT_TIMER0	0x0002
-#define BRIDGE_INT_TIMER1	0x0004
 #define BRIDGE_INT_TIMER1_CLR	(~0x0004)
 
 #define MAIN_IRQ_CAUSE		(ORION5X_BRIDGE_VIRT_BASE | 0x200)

arch/arm/mach-orion5x/include/mach/gpio.h

@@ -6,32 +6,4 @@
  * warranty of any kind, whether express or implied.
  */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <mach/irqs.h>
 #include <plat/gpio.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define GPIO_MAX		32
-#define GPIO_OUT(pin)		ORION5X_DEV_BUS_REG(0x100)
-#define GPIO_IO_CONF(pin)	ORION5X_DEV_BUS_REG(0x104)
-#define GPIO_BLINK_EN(pin)	ORION5X_DEV_BUS_REG(0x108)
-#define GPIO_IN_POL(pin)	ORION5X_DEV_BUS_REG(0x10c)
-#define GPIO_DATA_IN(pin)	ORION5X_DEV_BUS_REG(0x110)
-#define GPIO_EDGE_CAUSE(pin)	ORION5X_DEV_BUS_REG(0x114)
-#define GPIO_EDGE_MASK(pin)	ORION5X_DEV_BUS_REG(0x118)
-#define GPIO_LEVEL_MASK(pin)	ORION5X_DEV_BUS_REG(0x11c)
-
-static inline int gpio_to_irq(int pin)
-{
-	return pin + IRQ_ORION5X_GPIO_START;
-}
-
-static inline int irq_to_gpio(int irq)
-{
-	return irq - IRQ_ORION5X_GPIO_START;
-}
-
-
-#endif

arch/arm/mach-orion5x/include/mach/orion5x.h

@@ -73,6 +73,7 @@
 #define ORION5X_DEV_BUS_PHYS_BASE	(ORION5X_REGS_PHYS_BASE | 0x10000)
 #define ORION5X_DEV_BUS_VIRT_BASE	(ORION5X_REGS_VIRT_BASE | 0x10000)
 #define ORION5X_DEV_BUS_REG(x)		(ORION5X_DEV_BUS_VIRT_BASE | (x))
+#define  GPIO_VIRT_BASE			ORION5X_DEV_BUS_REG(0x0100)
 #define  SPI_PHYS_BASE			(ORION5X_DEV_BUS_PHYS_BASE | 0x0600)
 #define  I2C_PHYS_BASE			(ORION5X_DEV_BUS_PHYS_BASE | 0x1000)
 #define  UART0_PHYS_BASE		(ORION5X_DEV_BUS_PHYS_BASE | 0x2000)

arch/arm/mach-orion5x/irq.c

@@ -28,27 +28,12 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 
 void __init orion5x_init_irq(void)
 {
-	int i;
-
 	orion_irq_init(0, (void __iomem *)MAIN_IRQ_MASK);
 
 	/*
-	 * Mask and clear GPIO IRQ interrupts
-	 */
-	writel(0x0, GPIO_LEVEL_MASK(0));
-	writel(0x0, GPIO_EDGE_MASK(0));
-	writel(0x0, GPIO_EDGE_CAUSE(0));
-
-	/*
-	 * Register chained level handlers for GPIO IRQs by default.
-	 * User can use set_type() if he wants to use edge types handlers.
+	 * Initialize gpiolib for GPIOs 0-31.
 	 */
-	for (i = IRQ_ORION5X_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_chip);
-		set_irq_handler(i, handle_level_irq);
-		irq_desc[i].status |= IRQ_LEVEL;
-		set_irq_flags(i, IRQF_VALID);
-	}
+	orion_gpio_init(0, 32, GPIO_VIRT_BASE, 0, IRQ_ORION5X_GPIO_START);
 	set_irq_chained_handler(IRQ_ORION5X_GPIO_0_7, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_ORION5X_GPIO_8_15, gpio_irq_handler);
 	set_irq_chained_handler(IRQ_ORION5X_GPIO_16_23, gpio_irq_handler);

arch/arm/mach-orion5x/kurobox_pro-setup.c

@@ -382,6 +382,7 @@ MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
 	.boot_params	= 0x00000100,
 	.init_machine	= kurobox_pro_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,
@@ -394,6 +395,7 @@ MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
 	.boot_params	= 0x00000100,
 	.init_machine	= kurobox_pro_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/ls-chl-setup.c

@@ -321,6 +321,7 @@ MACHINE_START(LINKSTATION_LSCHL, "Buffalo Linkstation LiveV3 (LS-CHL)")
 	.boot_params	= 0x00000100,
 	.init_machine	= lschl_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/ls_hgl-setup.c

@@ -268,6 +268,7 @@ MACHINE_START(LINKSTATION_LS_HGL, "Buffalo Linkstation LS-HGL")
 	.boot_params	= 0x00000100,
 	.init_machine	= ls_hgl_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/lsmini-setup.c

@@ -270,6 +270,7 @@ MACHINE_START(LINKSTATION_MINI, "Buffalo Linkstation Mini")
 	.boot_params	= 0x00000100,
 	.init_machine	= lsmini_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/mpp.c

@@ -124,9 +124,6 @@ void __init orion5x_mpp_conf(struct orion5x_mpp_mode *mode)
 	u32 mpp_8_15_ctrl = readl(MPP_8_15_CTRL);
 	u32 mpp_16_19_ctrl = readl(MPP_16_19_CTRL);
 
-	/* Initialize gpiolib. */
-	orion_gpio_init();
-
 	for ( ; mode->mpp >= 0; mode++) {
 		u32 *reg;
 		int num_type;

arch/arm/mach-orion5x/mss2-setup.c

@@ -264,6 +264,7 @@ MACHINE_START(MSS2, "Maxtor Shared Storage II")
 	.boot_params	= 0x00000100,
 	.init_machine	= mss2_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32

arch/arm/mach-orion5x/mv2120-setup.c

@@ -232,6 +232,7 @@ MACHINE_START(MV2120, "HP Media Vault mv2120")
 	.boot_params	= 0x00000100,
 	.init_machine	= mv2120_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32

arch/arm/mach-orion5x/net2big-setup.c

@@ -422,6 +422,7 @@ MACHINE_START(NET2BIG, "LaCie 2Big Network")
 	.boot_params	= 0x00000100,
 	.init_machine	= net2big_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c

@@ -172,6 +172,7 @@ MACHINE_START(RD88F5181L_FXO, "Marvell Orion-VoIP FXO Reference Design")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f5181l_fxo_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/rd88f5181l-ge-setup.c

@@ -184,6 +184,7 @@ MACHINE_START(RD88F5181L_GE, "Marvell Orion-VoIP GE Reference Design")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f5181l_ge_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/rd88f5182-setup.c

@@ -308,6 +308,7 @@ MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f5182_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 MACHINE_END

arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c

@@ -126,6 +126,7 @@ MACHINE_START(RD88F6183AP_GE, "Marvell Orion-1-90 AP GE Reference Design")
 	.boot_params	= 0x00000100,
 	.init_machine	= rd88f6183ap_ge_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/terastation_pro2-setup.c

@@ -361,6 +361,7 @@ MACHINE_START(TERASTATION_PRO2, "Buffalo Terastation Pro II/Live")
 	.boot_params	= 0x00000100,
 	.init_machine	= tsp2_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/ts209-setup.c

@@ -325,6 +325,7 @@ MACHINE_START(TS209, "QNAP TS-109/TS-209")
 	.boot_params	= 0x00000100,
 	.init_machine	= qnap_ts209_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/ts409-setup.c

@@ -314,6 +314,7 @@ MACHINE_START(TS409, "QNAP TS-409")
 	.boot_params	= 0x00000100,
 	.init_machine	= qnap_ts409_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/ts78xx-fpga.h

+#define TS7800_FPGA_MAGIC 0x00b480
 #define FPGAID(_magic, _rev) ((_magic << 8) + _rev)
 
 /*
@@ -6,11 +7,15 @@
  */
 enum fpga_ids {
 	/* Technologic Systems */
-	TS7800_REV_1	= FPGAID(0x00b480, 0x01),
-	TS7800_REV_2	= FPGAID(0x00b480, 0x02),
-	TS7800_REV_3	= FPGAID(0x00b480, 0x03),
-	TS7800_REV_4	= FPGAID(0x00b480, 0x04),
-	TS7800_REV_5	= FPGAID(0x00b480, 0x05),
+	TS7800_REV_1	= FPGAID(TS7800_FPGA_MAGIC, 0x01),
+	TS7800_REV_2	= FPGAID(TS7800_FPGA_MAGIC, 0x02),
+	TS7800_REV_3	= FPGAID(TS7800_FPGA_MAGIC, 0x03),
+	TS7800_REV_4	= FPGAID(TS7800_FPGA_MAGIC, 0x04),
+	TS7800_REV_5	= FPGAID(TS7800_FPGA_MAGIC, 0x05),
+	TS7800_REV_6	= FPGAID(TS7800_FPGA_MAGIC, 0x06),
+	TS7800_REV_7	= FPGAID(TS7800_FPGA_MAGIC, 0x07),
+	TS7800_REV_8	= FPGAID(TS7800_FPGA_MAGIC, 0x08),
+	TS7800_REV_9	= FPGAID(TS7800_FPGA_MAGIC, 0x09),
 
 	/* Unaffordable & Expensive */
 	UAE_DUMMY	= FPGAID(0xffffff, 0x01),

arch/arm/mach-orion5x/ts78xx-setup.c

@@ -191,6 +191,60 @@ static int ts78xx_ts_nand_dev_ready(struct mtd_info *mtd)
 	return readb(TS_NAND_CTRL) & 0x20;
 }
 
+static void ts78xx_ts_nand_write_buf(struct mtd_info *mtd,
+			const uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	void __iomem *io_base = chip->IO_ADDR_W;
+	unsigned long off = ((unsigned long)buf & 3);
+	int sz;
+
+	if (off) {
+		sz = min_t(int, 4 - off, len);
+		writesb(io_base, buf, sz);
+		buf += sz;
+		len -= sz;
+	}
+
+	sz = len >> 2;
+	if (sz) {
+		u32 *buf32 = (u32 *)buf;
+		writesl(io_base, buf32, sz);
+		buf += sz << 2;
+		len -= sz << 2;
+	}
+
+	if (len)
+		writesb(io_base, buf, len);
+}
+
+static void ts78xx_ts_nand_read_buf(struct mtd_info *mtd,
+			uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+	void __iomem *io_base = chip->IO_ADDR_R;
+	unsigned long off = ((unsigned long)buf & 3);
+	int sz;
+
+	if (off) {
+		sz = min_t(int, 4 - off, len);
+		readsb(io_base, buf, sz);
+		buf += sz;
+		len -= sz;
+	}
+
+	sz = len >> 2;
+	if (sz) {
+		u32 *buf32 = (u32 *)buf;
+		readsl(io_base, buf32, sz);
+		buf += sz << 2;
+		len -= sz << 2;
+	}
+
+	if (len)
+		readsb(io_base, buf, len);
+}
+
 const char *ts_nand_part_probes[] = { "cmdlinepart", NULL };
 
 static struct mtd_partition ts78xx_ts_nand_parts[] = {
@@ -233,6 +287,8 @@ static struct platform_nand_data ts78xx_ts_nand_data = {
 		 */
 		.cmd_ctrl		= ts78xx_ts_nand_cmd_ctrl,
 		.dev_ready		= ts78xx_ts_nand_dev_ready,
+		.write_buf		= ts78xx_ts_nand_write_buf,
+		.read_buf		= ts78xx_ts_nand_read_buf,
 	},
 };
 
@@ -334,14 +390,29 @@ static void ts78xx_fpga_supports(void)
 	case TS7800_REV_3:
 	case TS7800_REV_4:
 	case TS7800_REV_5:
+	case TS7800_REV_6:
+	case TS7800_REV_7:
+	case TS7800_REV_8:
+	case TS7800_REV_9:
 		ts78xx_fpga.supports.ts_rtc.present = 1;
 		ts78xx_fpga.supports.ts_nand.present = 1;
 		ts78xx_fpga.supports.ts_rng.present = 1;
 		break;
 	default:
-		ts78xx_fpga.supports.ts_rtc.present = 0;
-		ts78xx_fpga.supports.ts_nand.present = 0;
-		ts78xx_fpga.supports.ts_rng.present = 0;
+		/* enable devices if magic matches */
+		switch ((ts78xx_fpga.id >> 8) & 0xffffff) {
+		case TS7800_FPGA_MAGIC:
+			printk(KERN_WARNING "TS-7800 FPGA: unrecognized revision 0x%.2x\n",
+					ts78xx_fpga.id & 0xff);
+			ts78xx_fpga.supports.ts_rtc.present = 1;
+			ts78xx_fpga.supports.ts_nand.present = 1;
+			ts78xx_fpga.supports.ts_rng.present = 1;
+			break;
+		default:
+			ts78xx_fpga.supports.ts_rtc.present = 0;
+			ts78xx_fpga.supports.ts_nand.present = 0;
+			ts78xx_fpga.supports.ts_rng.present = 0;
+		}
 	}
 }
 
@@ -553,6 +624,7 @@ MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC")
 	.boot_params	= 0x00000100,
 	.init_machine	= ts78xx_init,
 	.map_io		= ts78xx_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 MACHINE_END

arch/arm/mach-orion5x/wnr854t-setup.c

@@ -175,6 +175,7 @@ MACHINE_START(WNR854T, "Netgear WNR854T")
 	.boot_params	= 0x00000100,
 	.init_machine	= wnr854t_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-orion5x/wrt350n-v2-setup.c

@@ -263,6 +263,7 @@ MACHINE_START(WRT350N_V2, "Linksys WRT350N v2")
 	.boot_params	= 0x00000100,
 	.init_machine	= wrt350n_v2_init,
 	.map_io		= orion5x_map_io,
+	.init_early	= orion5x_init_early,
 	.init_irq	= orion5x_init_irq,
 	.timer		= &orion5x_timer,
 	.fixup		= tag_fixup_mem32,

arch/arm/mach-s5p6442/include/mach/map.h

 /* linux/arch/arm/mach-s5p6442/include/mach/map.h
  *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
  * S5P6442 - Memory map definitions
@@ -16,56 +16,61 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5P6442_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5P6442_PA_CHIPID
+#define S5P6442_PA_SDRAM	0x20000000
 
-#define S5P6442_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5P6442_PA_SYSCON
+#define S5P6442_PA_I2S0		0xC0B00000
+#define S5P6442_PA_I2S1		0xF2200000
 
-#define S5P6442_PA_GPIO		(0xE0200000)
+#define S5P6442_PA_CHIPID	0xE0000000
 
-#define S5P6442_PA_VIC0		(0xE4000000)
-#define S5P6442_PA_VIC1		(0xE4100000)
-#define S5P6442_PA_VIC2		(0xE4200000)
+#define S5P6442_PA_SYSCON	0xE0100000
 
-#define S5P6442_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5P6442_PA_SROMC
+#define S5P6442_PA_GPIO		0xE0200000
 
-#define S5P6442_PA_MDMA		0xE8000000
-#define S5P6442_PA_PDMA		0xE9000000
+#define S5P6442_PA_VIC0		0xE4000000
+#define S5P6442_PA_VIC1		0xE4100000
+#define S5P6442_PA_VIC2		0xE4200000
 
-#define S5P6442_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5P6442_PA_TIMER
+#define S5P6442_PA_SROMC	0xE7000000
 
-#define S5P6442_PA_SYSTIMER   	(0xEA100000)
+#define S5P6442_PA_MDMA		0xE8000000
+#define S5P6442_PA_PDMA		0xE9000000
 
-#define S5P6442_PA_WATCHDOG	(0xEA200000)
+#define S5P6442_PA_TIMER	0xEA000000
 
-#define S5P6442_PA_UART		(0xEC000000)
+#define S5P6442_PA_SYSTIMER	0xEA100000
 
-#define S5P_PA_UART0		(S5P6442_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5P6442_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5P6442_PA_UART + 0x800)
-#define S5P_SZ_UART		SZ_256
+#define S5P6442_PA_WATCHDOG	0xEA200000
 
-#define S5P6442_PA_IIC0		(0xEC100000)
+#define S5P6442_PA_UART		0xEC000000
 
-#define S5P6442_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5P6442_PA_SDRAM
+#define S5P6442_PA_IIC0		0xEC100000
 
 #define S5P6442_PA_SPI		0xEC300000
 
-/* I2S */
-#define S5P6442_PA_I2S0		0xC0B00000
-#define S5P6442_PA_I2S1		0xF2200000
-
-/* PCM */
 #define S5P6442_PA_PCM0		0xF2400000
 #define S5P6442_PA_PCM1		0xF2500000
 
-/* compatibiltiy defines. */
+/* Compatibiltiy Defines */
+
+#define S3C_PA_IIC		S5P6442_PA_IIC0
 #define S3C_PA_WDT		S5P6442_PA_WATCHDOG
+
+#define S5P_PA_CHIPID		S5P6442_PA_CHIPID
+#define S5P_PA_SDRAM		S5P6442_PA_SDRAM
+#define S5P_PA_SROMC		S5P6442_PA_SROMC
+#define S5P_PA_SYSCON		S5P6442_PA_SYSCON
+#define S5P_PA_TIMER		S5P6442_PA_TIMER
+
+/* UART */
+
 #define S3C_PA_UART		S5P6442_PA_UART
-#define S3C_PA_IIC		S5P6442_PA_IIC0
+
+#define S5P_PA_UART(x)		(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0		S5P_PA_UART(0)
+#define S5P_PA_UART1		S5P_PA_UART(1)
+#define S5P_PA_UART2		S5P_PA_UART(2)
+
+#define S5P_SZ_UART		SZ_256
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5p64x0/include/mach/map.h

 /* linux/arch/arm/mach-s5p64x0/include/mach/map.h
  *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2009-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
  * S5P64X0 - Memory map definitions
@@ -16,64 +16,46 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5P64X0_PA_SDRAM	(0x20000000)
+#define S5P64X0_PA_SDRAM	0x20000000
 
-#define S5P64X0_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5P64X0_PA_CHIPID
-
-#define S5P64X0_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5P64X0_PA_SYSCON
-
-#define S5P64X0_PA_GPIO		(0xE0308000)
-
-#define S5P64X0_PA_VIC0		(0xE4000000)
-#define S5P64X0_PA_VIC1		(0xE4100000)
+#define S5P64X0_PA_CHIPID	0xE0000000
 
-#define S5P64X0_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5P64X0_PA_SROMC
-
-#define S5P64X0_PA_PDMA		(0xE9000000)
-
-#define S5P64X0_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5P64X0_PA_TIMER
+#define S5P64X0_PA_SYSCON	0xE0100000
 
-#define S5P64X0_PA_RTC		(0xEA100000)
+#define S5P64X0_PA_GPIO		0xE0308000
 
-#define S5P64X0_PA_WDT		(0xEA200000)
+#define S5P64X0_PA_VIC0		0xE4000000
+#define S5P64X0_PA_VIC1		0xE4100000
 
-#define S5P6440_PA_UART(x)	(0xEC000000 + ((x) * S3C_UART_OFFSET))
-#define S5P6450_PA_UART(x)	((x < 5) ? (0xEC800000 + ((x) * S3C_UART_OFFSET)) : (0xEC000000))
+#define S5P64X0_PA_SROMC	0xE7000000
 
-#define S5P_PA_UART0		S5P6450_PA_UART(0)
-#define S5P_PA_UART1		S5P6450_PA_UART(1)
-#define S5P_PA_UART2		S5P6450_PA_UART(2)
-#define S5P_PA_UART3		S5P6450_PA_UART(3)
-#define S5P_PA_UART4		S5P6450_PA_UART(4)
-#define S5P_PA_UART5		S5P6450_PA_UART(5)
+#define S5P64X0_PA_PDMA		0xE9000000
 
-#define S5P_SZ_UART		SZ_256
+#define S5P64X0_PA_TIMER	0xEA000000
+#define S5P64X0_PA_RTC		0xEA100000
+#define S5P64X0_PA_WDT		0xEA200000
 
-#define S5P6440_PA_IIC0		(0xEC104000)
-#define S5P6440_PA_IIC1		(0xEC20F000)
-#define S5P6450_PA_IIC0		(0xEC100000)
-#define S5P6450_PA_IIC1		(0xEC200000)
+#define S5P6440_PA_IIC0		0xEC104000
+#define S5P6440_PA_IIC1		0xEC20F000
+#define S5P6450_PA_IIC0		0xEC100000
+#define S5P6450_PA_IIC1		0xEC200000
 
-#define S5P64X0_PA_SPI0		(0xEC400000)
-#define S5P64X0_PA_SPI1		(0xEC500000)
+#define S5P64X0_PA_SPI0		0xEC400000
+#define S5P64X0_PA_SPI1		0xEC500000
 
-#define S5P64X0_PA_HSOTG	(0xED100000)
+#define S5P64X0_PA_HSOTG	0xED100000
 
 #define S5P64X0_PA_HSMMC(x)	(0xED800000 + ((x) * 0x100000))
 
-#define S5P64X0_PA_I2S		(0xF2000000)
+#define S5P64X0_PA_I2S		0xF2000000
 #define S5P6450_PA_I2S1		0xF2800000
 #define S5P6450_PA_I2S2		0xF2900000
 
-#define S5P64X0_PA_PCM		(0xF2100000)
+#define S5P64X0_PA_PCM		0xF2100000
 
-#define S5P64X0_PA_ADC		(0xF3000000)
+#define S5P64X0_PA_ADC		0xF3000000
 
-/* compatibiltiy defines. */
+/* Compatibiltiy Defines */
 
 #define S3C_PA_HSMMC0		S5P64X0_PA_HSMMC(0)
 #define S3C_PA_HSMMC1		S5P64X0_PA_HSMMC(1)
@@ -83,6 +65,25 @@
 #define S3C_PA_RTC		S5P64X0_PA_RTC
 #define S3C_PA_WDT		S5P64X0_PA_WDT
 
+#define S5P_PA_CHIPID		S5P64X0_PA_CHIPID
+#define S5P_PA_SROMC		S5P64X0_PA_SROMC
+#define S5P_PA_SYSCON		S5P64X0_PA_SYSCON
+#define S5P_PA_TIMER		S5P64X0_PA_TIMER
+
 #define SAMSUNG_PA_ADC		S5P64X0_PA_ADC
 
+/* UART */
+
+#define S5P6440_PA_UART(x)	(0xEC000000 + ((x) * S3C_UART_OFFSET))
+#define S5P6450_PA_UART(x)	((x < 5) ? (0xEC800000 + ((x) * S3C_UART_OFFSET)) : (0xEC000000))
+
+#define S5P_PA_UART0		S5P6450_PA_UART(0)
+#define S5P_PA_UART1		S5P6450_PA_UART(1)
+#define S5P_PA_UART2		S5P6450_PA_UART(2)
+#define S5P_PA_UART3		S5P6450_PA_UART(3)
+#define S5P_PA_UART4		S5P6450_PA_UART(4)
+#define S5P_PA_UART5		S5P6450_PA_UART(5)
+
+#define S5P_SZ_UART		SZ_256
+
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pc100/include/mach/map.h

 /* linux/arch/arm/mach-s5pc100/include/mach/map.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
  *
  * Copyright 2009 Samsung Electronics Co.
  *	Byungho Min <bhmin@samsung.com>
@@ -16,145 +19,115 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-/*
- * map-base.h has already defined virtual memory address
- * S3C_VA_IRQ		S3C_ADDR(0x00000000)	irq controller(s)
- * S3C_VA_SYS		S3C_ADDR(0x00100000)	system control
- * S3C_VA_MEM		S3C_ADDR(0x00200000)	system control (not used)
- * S3C_VA_TIMER		S3C_ADDR(0x00300000)	timer block
- * S3C_VA_WATCHDOG	S3C_ADDR(0x00400000)	watchdog
- * S3C_VA_UART		S3C_ADDR(0x01000000)	UART
- *
- * S5PC100 specific virtual memory address can be defined here
- * S5PC1XX_VA_GPIO	S3C_ADDR(0x00500000)	GPIO
- *
- */
+#define S5PC100_PA_SDRAM		0x20000000
+
+#define S5PC100_PA_ONENAND		0xE7100000
+#define S5PC100_PA_ONENAND_BUF		0xB0000000
+
+#define S5PC100_PA_CHIPID		0xE0000000
 
-#define S5PC100_PA_ONENAND_BUF	(0xB0000000)
-#define S5PC100_SZ_ONENAND_BUF	(SZ_256M - SZ_32M)
+#define S5PC100_PA_SYSCON		0xE0100000
 
-/* Chip ID */
+#define S5PC100_PA_OTHERS		0xE0200000
 
-#define S5PC100_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5PC100_PA_CHIPID
+#define S5PC100_PA_GPIO			0xE0300000
 
-#define S5PC100_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5PC100_PA_SYSCON
+#define S5PC100_PA_VIC0			0xE4000000
+#define S5PC100_PA_VIC1			0xE4100000
+#define S5PC100_PA_VIC2			0xE4200000
 
-#define S5PC100_PA_OTHERS	(0xE0200000)
-#define S5PC100_VA_OTHERS	(S3C_VA_SYS + 0x10000)
+#define S5PC100_PA_SROMC		0xE7000000
 
-#define S5PC100_PA_GPIO		(0xE0300000)
-#define S5PC1XX_VA_GPIO		S3C_ADDR(0x00500000)
+#define S5PC100_PA_CFCON		0xE7800000
 
-/* Interrupt */
-#define S5PC100_PA_VIC0		(0xE4000000)
-#define S5PC100_PA_VIC1		(0xE4100000)
-#define S5PC100_PA_VIC2		(0xE4200000)
-#define S5PC100_VA_VIC		S3C_VA_IRQ
-#define S5PC100_VA_VIC_OFFSET	0x10000
-#define S5PC1XX_VA_VIC(x)	(S5PC100_VA_VIC + ((x) * S5PC100_VA_VIC_OFFSET))
+#define S5PC100_PA_MDMA			0xE8100000
+#define S5PC100_PA_PDMA0		0xE9000000
+#define S5PC100_PA_PDMA1		0xE9200000
 
-#define S5PC100_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5PC100_PA_SROMC
+#define S5PC100_PA_TIMER		0xEA000000
+#define S5PC100_PA_SYSTIMER		0xEA100000
+#define S5PC100_PA_WATCHDOG		0xEA200000
+#define S5PC100_PA_RTC			0xEA300000
 
-#define S5PC100_PA_ONENAND	(0xE7100000)
+#define S5PC100_PA_UART			0xEC000000
 
-#define S5PC100_PA_CFCON	(0xE7800000)
+#define S5PC100_PA_IIC0			0xEC100000
+#define S5PC100_PA_IIC1			0xEC200000
 
-/* DMA */
-#define S5PC100_PA_MDMA		(0xE8100000)
-#define S5PC100_PA_PDMA0	(0xE9000000)
-#define S5PC100_PA_PDMA1	(0xE9200000)
+#define S5PC100_PA_SPI0			0xEC300000
+#define S5PC100_PA_SPI1			0xEC400000
+#define S5PC100_PA_SPI2			0xEC500000
 
-/* Timer */
-#define S5PC100_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5PC100_PA_TIMER
+#define S5PC100_PA_USB_HSOTG		0xED200000
+#define S5PC100_PA_USB_HSPHY		0xED300000
 
-#define S5PC100_PA_SYSTIMER	(0xEA100000)
+#define S5PC100_PA_HSMMC(x)		(0xED800000 + ((x) * 0x100000))
 
-#define S5PC100_PA_WATCHDOG	(0xEA200000)
-#define S5PC100_PA_RTC		(0xEA300000)
+#define S5PC100_PA_FB			0xEE000000
 
-#define S5PC100_PA_UART		(0xEC000000)
+#define S5PC100_PA_FIMC0		0xEE200000
+#define S5PC100_PA_FIMC1		0xEE300000
+#define S5PC100_PA_FIMC2		0xEE400000
 
-#define S5P_PA_UART0		(S5PC100_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5PC100_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5PC100_PA_UART + 0x800)
-#define S5P_PA_UART3		(S5PC100_PA_UART + 0xC00)
-#define S5P_SZ_UART		SZ_256
+#define S5PC100_PA_I2S0			0xF2000000
+#define S5PC100_PA_I2S1			0xF2100000
+#define S5PC100_PA_I2S2			0xF2200000
 
-#define S5PC100_PA_IIC0		(0xEC100000)
-#define S5PC100_PA_IIC1		(0xEC200000)
+#define S5PC100_PA_AC97			0xF2300000
 
-/* SPI */
-#define S5PC100_PA_SPI0		0xEC300000
-#define S5PC100_PA_SPI1		0xEC400000
-#define S5PC100_PA_SPI2		0xEC500000
+#define S5PC100_PA_PCM0			0xF2400000
+#define S5PC100_PA_PCM1			0xF2500000
 
-/* USB HS OTG */
-#define S5PC100_PA_USB_HSOTG	(0xED200000)
-#define S5PC100_PA_USB_HSPHY	(0xED300000)
+#define S5PC100_PA_SPDIF		0xF2600000
 
-#define S5PC100_PA_FB		(0xEE000000)
+#define S5PC100_PA_TSADC		0xF3000000
 
-#define S5PC100_PA_FIMC0	(0xEE200000)
-#define S5PC100_PA_FIMC1	(0xEE300000)
-#define S5PC100_PA_FIMC2	(0xEE400000)
+#define S5PC100_PA_KEYPAD		0xF3100000
 
-#define S5PC100_PA_I2S0		(0xF2000000)
-#define S5PC100_PA_I2S1		(0xF2100000)
-#define S5PC100_PA_I2S2		(0xF2200000)
+/* Compatibiltiy Defines */
 
-#define S5PC100_PA_AC97		0xF2300000
+#define S3C_PA_FB			S5PC100_PA_FB
+#define S3C_PA_HSMMC0			S5PC100_PA_HSMMC(0)
+#define S3C_PA_HSMMC1			S5PC100_PA_HSMMC(1)
+#define S3C_PA_HSMMC2			S5PC100_PA_HSMMC(2)
+#define S3C_PA_IIC			S5PC100_PA_IIC0
+#define S3C_PA_IIC1			S5PC100_PA_IIC1
+#define S3C_PA_KEYPAD			S5PC100_PA_KEYPAD
+#define S3C_PA_ONENAND			S5PC100_PA_ONENAND
+#define S3C_PA_ONENAND_BUF		S5PC100_PA_ONENAND_BUF
+#define S3C_PA_RTC			S5PC100_PA_RTC
+#define S3C_PA_TSADC			S5PC100_PA_TSADC
+#define S3C_PA_USB_HSOTG		S5PC100_PA_USB_HSOTG
+#define S3C_PA_USB_HSPHY		S5PC100_PA_USB_HSPHY
+#define S3C_PA_WDT			S5PC100_PA_WATCHDOG
 
-/* PCM */
-#define S5PC100_PA_PCM0		0xF2400000
-#define S5PC100_PA_PCM1		0xF2500000
+#define S5P_PA_CHIPID			S5PC100_PA_CHIPID
+#define S5P_PA_FIMC0			S5PC100_PA_FIMC0
+#define S5P_PA_FIMC1			S5PC100_PA_FIMC1
+#define S5P_PA_FIMC2			S5PC100_PA_FIMC2
+#define S5P_PA_SDRAM			S5PC100_PA_SDRAM
+#define S5P_PA_SROMC			S5PC100_PA_SROMC
+#define S5P_PA_SYSCON			S5PC100_PA_SYSCON
+#define S5P_PA_TIMER			S5PC100_PA_TIMER
 
-#define S5PC100_PA_SPDIF	0xF2600000
+#define SAMSUNG_PA_ADC			S5PC100_PA_TSADC
+#define SAMSUNG_PA_CFCON		S5PC100_PA_CFCON
+#define SAMSUNG_PA_KEYPAD		S5PC100_PA_KEYPAD
 
-#define S5PC100_PA_TSADC	(0xF3000000)
+#define S5PC100_VA_OTHERS		(S3C_VA_SYS + 0x10000)
 
-/* KEYPAD */
-#define S5PC100_PA_KEYPAD	(0xF3100000)
+#define S3C_SZ_ONENAND_BUF		(SZ_256M - SZ_32M)
 
-#define S5PC100_PA_HSMMC(x)	(0xED800000 + ((x) * 0x100000))
+/* UART */
 
-#define S5PC100_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5PC100_PA_SDRAM
+#define S3C_PA_UART			S5PC100_PA_UART
 
-/* compatibiltiy defines. */
-#define S3C_PA_UART		S5PC100_PA_UART
-#define S3C_PA_IIC		S5PC100_PA_IIC0
-#define S3C_PA_IIC1		S5PC100_PA_IIC1
-#define S3C_PA_FB		S5PC100_PA_FB
-#define S3C_PA_G2D		S5PC100_PA_G2D
-#define S3C_PA_G3D		S5PC100_PA_G3D
-#define S3C_PA_JPEG		S5PC100_PA_JPEG
-#define S3C_PA_ROTATOR		S5PC100_PA_ROTATOR
-#define S5P_VA_VIC0		S5PC1XX_VA_VIC(0)
-#define S5P_VA_VIC1		S5PC1XX_VA_VIC(1)
-#define S5P_VA_VIC2		S5PC1XX_VA_VIC(2)
-#define S3C_PA_USB_HSOTG	S5PC100_PA_USB_HSOTG
-#define S3C_PA_USB_HSPHY	S5PC100_PA_USB_HSPHY
-#define S3C_PA_HSMMC0		S5PC100_PA_HSMMC(0)
-#define S3C_PA_HSMMC1		S5PC100_PA_HSMMC(1)
-#define S3C_PA_HSMMC2		S5PC100_PA_HSMMC(2)
-#define S3C_PA_KEYPAD		S5PC100_PA_KEYPAD
-#define S3C_PA_WDT		S5PC100_PA_WATCHDOG
-#define S3C_PA_TSADC		S5PC100_PA_TSADC
-#define S3C_PA_ONENAND		S5PC100_PA_ONENAND
-#define S3C_PA_ONENAND_BUF	S5PC100_PA_ONENAND_BUF
-#define S3C_SZ_ONENAND_BUF	S5PC100_SZ_ONENAND_BUF
-#define S3C_PA_RTC		S5PC100_PA_RTC
-
-#define SAMSUNG_PA_ADC		S5PC100_PA_TSADC
-#define SAMSUNG_PA_CFCON	S5PC100_PA_CFCON
-#define SAMSUNG_PA_KEYPAD	S5PC100_PA_KEYPAD
+#define S5P_PA_UART(x)			(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0			S5P_PA_UART(0)
+#define S5P_PA_UART1			S5P_PA_UART(1)
+#define S5P_PA_UART2			S5P_PA_UART(2)
+#define S5P_PA_UART3			S5P_PA_UART(3)
 
-#define S5P_PA_FIMC0		S5PC100_PA_FIMC0
-#define S5P_PA_FIMC1		S5PC100_PA_FIMC1
-#define S5P_PA_FIMC2		S5PC100_PA_FIMC2
+#define S5P_SZ_UART			SZ_256
 
-#endif /* __ASM_ARCH_C100_MAP_H */
+#endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pv210/include/mach/map.h

 /* linux/arch/arm/mach-s5pv210/include/mach/map.h
  *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
  * S5PV210 - Memory map definitions
@@ -16,122 +16,120 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5PV210_PA_SROM_BANK5	(0xA8000000)
+#define S5PV210_PA_SDRAM		0x20000000
 
-#define S5PC110_PA_ONENAND	(0xB0000000)
-#define S5P_PA_ONENAND		S5PC110_PA_ONENAND
+#define S5PV210_PA_SROM_BANK5		0xA8000000
 
-#define S5PC110_PA_ONENAND_DMA	(0xB0600000)
-#define S5P_PA_ONENAND_DMA	S5PC110_PA_ONENAND_DMA
+#define S5PC110_PA_ONENAND		0xB0000000
+#define S5PC110_PA_ONENAND_DMA		0xB0600000
 
-#define S5PV210_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5PV210_PA_CHIPID
+#define S5PV210_PA_CHIPID		0xE0000000
 
-#define S5PV210_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5PV210_PA_SYSCON
+#define S5PV210_PA_SYSCON		0xE0100000
 
-#define S5PV210_PA_GPIO		(0xE0200000)
+#define S5PV210_PA_GPIO			0xE0200000
 
-/* SPI */
-#define S5PV210_PA_SPI0		0xE1300000
-#define S5PV210_PA_SPI1		0xE1400000
+#define S5PV210_PA_SPDIF		0xE1100000
 
-#define S5PV210_PA_KEYPAD	(0xE1600000)
+#define S5PV210_PA_SPI0			0xE1300000
+#define S5PV210_PA_SPI1			0xE1400000
 
-#define S5PV210_PA_IIC0		(0xE1800000)
-#define S5PV210_PA_IIC1		(0xFAB00000)
-#define S5PV210_PA_IIC2		(0xE1A00000)
+#define S5PV210_PA_KEYPAD		0xE1600000
 
-#define S5PV210_PA_TIMER	(0xE2500000)
-#define S5P_PA_TIMER		S5PV210_PA_TIMER
+#define S5PV210_PA_ADC			0xE1700000
 
-#define S5PV210_PA_SYSTIMER	(0xE2600000)
+#define S5PV210_PA_IIC0			0xE1800000
+#define S5PV210_PA_IIC1			0xFAB00000
+#define S5PV210_PA_IIC2			0xE1A00000
 
-#define S5PV210_PA_WATCHDOG	(0xE2700000)
+#define S5PV210_PA_AC97			0xE2200000
 
-#define S5PV210_PA_RTC		(0xE2800000)
-#define S5PV210_PA_UART		(0xE2900000)
+#define S5PV210_PA_PCM0			0xE2300000
+#define S5PV210_PA_PCM1			0xE1200000
+#define S5PV210_PA_PCM2			0xE2B00000
 
-#define S5P_PA_UART0		(S5PV210_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5PV210_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5PV210_PA_UART + 0x800)
-#define S5P_PA_UART3		(S5PV210_PA_UART + 0xC00)
+#define S5PV210_PA_TIMER		0xE2500000
+#define S5PV210_PA_SYSTIMER		0xE2600000
+#define S5PV210_PA_WATCHDOG		0xE2700000
+#define S5PV210_PA_RTC			0xE2800000
 
-#define S5P_SZ_UART		SZ_256
+#define S5PV210_PA_UART			0xE2900000
 
-#define S3C_VA_UARTx(x)		(S3C_VA_UART + ((x) * S3C_UART_OFFSET))
+#define S5PV210_PA_SROMC		0xE8000000
 
-#define S5PV210_PA_SROMC	(0xE8000000)
-#define S5P_PA_SROMC		S5PV210_PA_SROMC
+#define S5PV210_PA_CFCON		0xE8200000
 
-#define S5PV210_PA_CFCON	(0xE8200000)
+#define S5PV210_PA_HSMMC(x)		(0xEB000000 + ((x) * 0x100000))
 
-#define S5PV210_PA_MDMA		0xFA200000
-#define S5PV210_PA_PDMA0	0xE0900000
-#define S5PV210_PA_PDMA1	0xE0A00000
+#define S5PV210_PA_HSOTG		0xEC000000
+#define S5PV210_PA_HSPHY		0xEC100000
 
-#define S5PV210_PA_FB		(0xF8000000)
+#define S5PV210_PA_IIS0			0xEEE30000
+#define S5PV210_PA_IIS1			0xE2100000
+#define S5PV210_PA_IIS2			0xE2A00000
 
-#define S5PV210_PA_FIMC0	(0xFB200000)
-#define S5PV210_PA_FIMC1	(0xFB300000)
-#define S5PV210_PA_FIMC2	(0xFB400000)
+#define S5PV210_PA_DMC0			0xF0000000
+#define S5PV210_PA_DMC1			0xF1400000
 
-#define S5PV210_PA_HSMMC(x)	(0xEB000000 + ((x) * 0x100000))
+#define S5PV210_PA_VIC0			0xF2000000
+#define S5PV210_PA_VIC1			0xF2100000
+#define S5PV210_PA_VIC2			0xF2200000
+#define S5PV210_PA_VIC3			0xF2300000
 
-#define S5PV210_PA_HSOTG	(0xEC000000)
-#define S5PV210_PA_HSPHY	(0xEC100000)
+#define S5PV210_PA_FB			0xF8000000
 
-#define S5PV210_PA_VIC0		(0xF2000000)
-#define S5PV210_PA_VIC1		(0xF2100000)
-#define S5PV210_PA_VIC2		(0xF2200000)
-#define S5PV210_PA_VIC3		(0xF2300000)
+#define S5PV210_PA_MDMA			0xFA200000
+#define S5PV210_PA_PDMA0		0xE0900000
+#define S5PV210_PA_PDMA1		0xE0A00000
 
-#define S5PV210_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5PV210_PA_SDRAM
+#define S5PV210_PA_MIPI_CSIS		0xFA600000
 
-/* S/PDIF */
-#define S5PV210_PA_SPDIF	0xE1100000
+#define S5PV210_PA_FIMC0		0xFB200000
+#define S5PV210_PA_FIMC1		0xFB300000
+#define S5PV210_PA_FIMC2		0xFB400000
 
-/* I2S */
-#define S5PV210_PA_IIS0		0xEEE30000
-#define S5PV210_PA_IIS1		0xE2100000
-#define S5PV210_PA_IIS2		0xE2A00000
+/* Compatibiltiy Defines */
 
-/* PCM */
-#define S5PV210_PA_PCM0		0xE2300000
-#define S5PV210_PA_PCM1		0xE1200000
-#define S5PV210_PA_PCM2		0xE2B00000
+#define S3C_PA_FB			S5PV210_PA_FB
+#define S3C_PA_HSMMC0			S5PV210_PA_HSMMC(0)
+#define S3C_PA_HSMMC1			S5PV210_PA_HSMMC(1)
+#define S3C_PA_HSMMC2			S5PV210_PA_HSMMC(2)
+#define S3C_PA_HSMMC3			S5PV210_PA_HSMMC(3)
+#define S3C_PA_IIC			S5PV210_PA_IIC0
+#define S3C_PA_IIC1			S5PV210_PA_IIC1
+#define S3C_PA_IIC2			S5PV210_PA_IIC2
+#define S3C_PA_RTC			S5PV210_PA_RTC
+#define S3C_PA_USB_HSOTG		S5PV210_PA_HSOTG
+#define S3C_PA_WDT			S5PV210_PA_WATCHDOG
 
-/* AC97 */
-#define S5PV210_PA_AC97		0xE2200000
+#define S5P_PA_CHIPID			S5PV210_PA_CHIPID
+#define S5P_PA_FIMC0			S5PV210_PA_FIMC0
+#define S5P_PA_FIMC1			S5PV210_PA_FIMC1
+#define S5P_PA_FIMC2			S5PV210_PA_FIMC2
+#define S5P_PA_MIPI_CSIS0		S5PV210_PA_MIPI_CSIS
+#define S5P_PA_ONENAND			S5PC110_PA_ONENAND
+#define S5P_PA_ONENAND_DMA		S5PC110_PA_ONENAND_DMA
+#define S5P_PA_SDRAM			S5PV210_PA_SDRAM
+#define S5P_PA_SROMC			S5PV210_PA_SROMC
+#define S5P_PA_SYSCON			S5PV210_PA_SYSCON
+#define S5P_PA_TIMER			S5PV210_PA_TIMER
 
-#define S5PV210_PA_ADC		(0xE1700000)
+#define SAMSUNG_PA_ADC			S5PV210_PA_ADC
+#define SAMSUNG_PA_CFCON		S5PV210_PA_CFCON
+#define SAMSUNG_PA_KEYPAD		S5PV210_PA_KEYPAD
 
-#define S5PV210_PA_DMC0		(0xF0000000)
-#define S5PV210_PA_DMC1		(0xF1400000)
+/* UART */
 
-#define S5PV210_PA_MIPI_CSIS	0xFA600000
+#define S3C_VA_UARTx(x)			(S3C_VA_UART + ((x) * S3C_UART_OFFSET))
 
-/* compatibiltiy defines. */
-#define S3C_PA_UART		S5PV210_PA_UART
-#define S3C_PA_HSMMC0		S5PV210_PA_HSMMC(0)
-#define S3C_PA_HSMMC1		S5PV210_PA_HSMMC(1)
-#define S3C_PA_HSMMC2		S5PV210_PA_HSMMC(2)
-#define S3C_PA_HSMMC3		S5PV210_PA_HSMMC(3)
-#define S3C_PA_IIC		S5PV210_PA_IIC0
-#define S3C_PA_IIC1		S5PV210_PA_IIC1
-#define S3C_PA_IIC2		S5PV210_PA_IIC2
-#define S3C_PA_FB		S5PV210_PA_FB
-#define S3C_PA_RTC		S5PV210_PA_RTC
-#define S3C_PA_WDT		S5PV210_PA_WATCHDOG
-#define S3C_PA_USB_HSOTG	S5PV210_PA_HSOTG
-#define S5P_PA_FIMC0		S5PV210_PA_FIMC0
-#define S5P_PA_FIMC1		S5PV210_PA_FIMC1
-#define S5P_PA_FIMC2		S5PV210_PA_FIMC2
-#define S5P_PA_MIPI_CSIS0	S5PV210_PA_MIPI_CSIS
+#define S3C_PA_UART			S5PV210_PA_UART
 
-#define SAMSUNG_PA_ADC		S5PV210_PA_ADC
-#define SAMSUNG_PA_CFCON	S5PV210_PA_CFCON
-#define SAMSUNG_PA_KEYPAD	S5PV210_PA_KEYPAD
+#define S5P_PA_UART(x)			(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0			S5P_PA_UART(0)
+#define S5P_PA_UART1			S5P_PA_UART(1)
+#define S5P_PA_UART2			S5P_PA_UART(2)
+#define S5P_PA_UART3			S5P_PA_UART(3)
+
+#define S5P_SZ_UART			SZ_256
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pv210/mach-aquila.c

@@ -149,7 +149,7 @@ static struct regulator_init_data aquila_ldo2_data = {
 
 static struct regulator_init_data aquila_ldo3_data = {
 	.constraints	= {
-		.name		= "VUSB/MIPI_1.1V",
+		.name		= "VUSB+MIPI_1.1V",
 		.min_uV		= 1100000,
 		.max_uV		= 1100000,
 		.apply_uV	= 1,
@@ -197,7 +197,7 @@ static struct regulator_init_data aquila_ldo7_data = {
 
 static struct regulator_init_data aquila_ldo8_data = {
 	.constraints	= {
-		.name		= "VUSB/VADC_3.3V",
+		.name		= "VUSB+VADC_3.3V",
 		.min_uV		= 3300000,
 		.max_uV		= 3300000,
 		.apply_uV	= 1,
@@ -207,7 +207,7 @@ static struct regulator_init_data aquila_ldo8_data = {
 
 static struct regulator_init_data aquila_ldo9_data = {
 	.constraints	= {
-		.name		= "VCC/VCAM_2.8V",
+		.name		= "VCC+VCAM_2.8V",
 		.min_uV		= 2800000,
 		.max_uV		= 2800000,
 		.apply_uV	= 1,
@@ -381,9 +381,12 @@ static struct max8998_platform_data aquila_max8998_pdata = {
 	.buck1_set1	= S5PV210_GPH0(3),
 	.buck1_set2	= S5PV210_GPH0(4),
 	.buck2_set3	= S5PV210_GPH0(5),
-	.buck1_max_voltage1 = 1200000,
-	.buck1_max_voltage2 = 1200000,
-	.buck2_max_voltage = 1200000,
+	.buck1_voltage1	= 1200000,
+	.buck1_voltage2	= 1200000,
+	.buck1_voltage3	= 1200000,
+	.buck1_voltage4	= 1200000,
+	.buck2_voltage1	= 1200000,
+	.buck2_voltage2	= 1200000,
 };
 #endif