Commit 80886f7c authored by Srinath Mannam's avatar Srinath Mannam Committed by Kishon Vijay Abraham I

phy: Add stingray SATA phy support

This patch adds support for stingray SATA phy in the
SATA BRCM phy driver.
Signed-off-by: default avatarSrinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: default avatarKishon Vijay Abraham I <kishon@ti.com>
parent 3ac255bc
......@@ -46,6 +46,7 @@ enum brcm_sata_phy_version {
BRCM_SATA_PHY_STB_40NM,
BRCM_SATA_PHY_IPROC_NS2,
BRCM_SATA_PHY_IPROC_NSP,
BRCM_SATA_PHY_IPROC_SR,
};
struct brcm_sata_port {
......@@ -81,12 +82,17 @@ enum sata_phy_regs {
PLL_ACTRL2 = 0x8b,
PLL_ACTRL2_SELDIV_MASK = 0x1f,
PLL_ACTRL2_SELDIV_SHIFT = 9,
PLL_ACTRL6 = 0x86,
PLL1_REG_BANK = 0x060,
PLL1_ACTRL2 = 0x82,
PLL1_ACTRL3 = 0x83,
PLL1_ACTRL4 = 0x84,
TX_REG_BANK = 0x070,
TX_ACTRL0 = 0x80,
TX_ACTRL0_TXPOL_FLIP = BIT(6),
OOB_REG_BANK = 0x150,
OOB1_REG_BANK = 0x160,
OOB_CTRL1 = 0x80,
......@@ -347,6 +353,68 @@ static int brcm_nsp_sata_init(struct brcm_sata_port *port)
return 0;
}
/* SR PHY PLL0 registers */
#define SR_PLL0_ACTRL6_MAGIC 0xa
/* SR PHY PLL1 registers */
#define SR_PLL1_ACTRL2_MAGIC 0x32
#define SR_PLL1_ACTRL3_MAGIC 0x2
#define SR_PLL1_ACTRL4_MAGIC 0x3e8
static int brcm_sr_sata_init(struct brcm_sata_port *port)
{
struct brcm_sata_phy *priv = port->phy_priv;
struct device *dev = port->phy_priv->dev;
void __iomem *base = priv->phy_base;
unsigned int val, try;
/* Configure PHY PLL register bank 1 */
val = SR_PLL1_ACTRL2_MAGIC;
brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
val = SR_PLL1_ACTRL3_MAGIC;
brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
val = SR_PLL1_ACTRL4_MAGIC;
brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
/* Configure PHY PLL register bank 0 */
val = SR_PLL0_ACTRL6_MAGIC;
brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
/* Wait for PHY PLL lock by polling pll_lock bit */
try = 50;
do {
val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
BLOCK0_XGXSSTATUS);
if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
break;
msleep(20);
try--;
} while (try);
if ((val & BLOCK0_XGXSSTATUS_PLL_LOCK) == 0) {
/* PLL did not lock; give up */
dev_err(dev, "port%d PLL did not lock\n", port->portnum);
return -ETIMEDOUT;
}
/* Invert Tx polarity */
brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL0,
~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP);
/* Configure OOB control to handle 100MHz reference clock */
val = ((0xc << OOB_CTRL1_BURST_MAX_SHIFT) |
(0x4 << OOB_CTRL1_BURST_MIN_SHIFT) |
(0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) |
(0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT));
brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) |
(0x2 << OOB_CTRL2_BURST_CNT_SHIFT) |
(0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT));
brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
return 0;
}
static int brcm_sata_phy_init(struct phy *phy)
{
int rc;
......@@ -363,6 +431,9 @@ static int brcm_sata_phy_init(struct phy *phy)
case BRCM_SATA_PHY_IPROC_NSP:
rc = brcm_nsp_sata_init(port);
break;
case BRCM_SATA_PHY_IPROC_SR:
rc = brcm_sr_sata_init(port);
break;
default:
rc = -ENODEV;
}
......@@ -384,6 +455,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
.data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
{ .compatible = "brcm,iproc-nsp-sata-phy",
.data = (void *)BRCM_SATA_PHY_IPROC_NSP },
{ .compatible = "brcm,iproc-sr-sata-phy",
.data = (void *)BRCM_SATA_PHY_IPROC_SR },
{},
};
MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment