usb: musb: Remove extra PM runtime calls from 2430 glue layer

With PM runtime behaving, these are all now unnecessary.
Doing pm_runtime_get(musb->controller) will keep the parent
glue layer also active.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/musb/omap2430.c

@@ -268,13 +268,8 @@ static void omap_musb_mailbox_work(struct work_struct *mailbox_work)
 {
 	struct omap2430_glue *glue = container_of(mailbox_work,
 				struct omap2430_glue, omap_musb_mailbox_work);
-	struct musb *musb = glue_to_musb(glue);
-	struct device *dev = musb->controller;
 
-	pm_runtime_get_sync(dev);
 	omap_musb_set_mailbox(glue);
-	pm_runtime_mark_last_busy(dev);
-	pm_runtime_put_autosuspend(dev);
 }
 
 static irqreturn_t omap2430_musb_interrupt(int irq, void *__hci)
@@ -343,16 +338,6 @@ static int omap2430_musb_init(struct musb *musb)
 	musb->isr = omap2430_musb_interrupt;
 	phy_init(musb->phy);
 
-	/*
-	 * Enable runtime PM for musb parent (this driver). We can't
-	 * do it earlier as struct musb is not yet allocated and we
-	 * need to touch the musb registers for runtime PM.
-	 */
-	pm_runtime_enable(glue->dev);
-	status = pm_runtime_get_sync(glue->dev);
-	if (status < 0)
-		goto err1;
-
 	l = musb_readl(musb->mregs, OTG_INTERFSEL);
 
 	if (data->interface_type == MUSB_INTERFACE_UTMI) {
@@ -376,11 +361,7 @@ static int omap2430_musb_init(struct musb *musb)
 	if (glue->status != MUSB_UNKNOWN)
 		omap_musb_set_mailbox(glue);
 
-	pm_runtime_put(glue->dev);
 	return 0;
-
-err1:
-	return status;
 }
 
 static void omap2430_musb_enable(struct musb *musb)
@@ -588,11 +569,9 @@ static int omap2430_probe(struct platform_device *pdev)
 		goto err2;
 	}
 
-	/*
-	 * Note that we cannot enable PM runtime yet for this
-	 * driver as we need struct musb initialized first.
-	 * See omap2430_musb_init above.
-	 */
+	pm_runtime_enable(glue->dev);
+	pm_runtime_use_autosuspend(glue->dev);
+	pm_runtime_set_autosuspend_delay(glue->dev, 500);
 
 	ret = platform_device_add(musb);
 	if (ret) {
@@ -618,6 +597,7 @@ static int omap2430_remove(struct platform_device *pdev)
 	platform_device_unregister(glue->musb);
 	omap2430_set_power(musb, false, false);
 	pm_runtime_put_sync(glue->dev);
+	pm_runtime_dont_use_autosuspend(glue->dev);
 	pm_runtime_disable(glue->dev);
 
 	return 0;