Merge branch 'i2c-mux/for-next' of https://github.com/peda-r/i2c-mux into i2c/for-4.14

Documentation/admin-guide/pm/cpufreq.rst

@@ -237,6 +237,14 @@ are the following:
 	This attribute is not present if the scaling driver in use does not
 	support it.
 
+``cpuinfo_cur_freq``
+	Current frequency of the CPUs belonging to this policy as obtained from
+	the hardware (in KHz).
+
+	This is expected to be the frequency the hardware actually runs at.
+	If that frequency cannot be determined, this attribute should not
+	be present.
+
 ``cpuinfo_max_freq``
 	Maximum possible operating frequency the CPUs belonging to this policy
 	can run at (in kHz).

Documentation/devicetree/bindings/ata/sata_rcar.txt

 * Renesas R-Car SATA
 
 Required properties:
-- compatible		: should contain one of the following:
+- compatible		: should contain one or more of the following:
 			  - "renesas,sata-r8a7779" for R-Car H1
-			    ("renesas,rcar-sata" is deprecated)
 			  - "renesas,sata-r8a7790-es1" for R-Car H2 ES1
 			  - "renesas,sata-r8a7790" for R-Car H2 other than ES1
 			  - "renesas,sata-r8a7791" for R-Car M2-W
 			  - "renesas,sata-r8a7793" for R-Car M2-N
 			  - "renesas,sata-r8a7795" for R-Car H3
+			  - "renesas,rcar-gen2-sata" for a generic R-Car Gen2 compatible device
+			  - "renesas,rcar-gen3-sata" for a generic R-Car Gen3 compatible device
+			  - "renesas,rcar-sata" is deprecated
+
+			  When compatible with the generic version nodes
+			  must list the SoC-specific version corresponding
+			  to the platform first followed by the generic
+			  version.
+
 - reg			: address and length of the SATA registers;
 - interrupts		: must consist of one interrupt specifier.
 - clocks		: must contain a reference to the functional clock.
@@ -16,7 +24,7 @@ Required properties:
 Example:
 
 sata0: sata@ee300000 {
-	compatible = "renesas,sata-r8a7791";
+	compatible = "renesas,sata-r8a7791", "renesas,rcar-gen2-sata";
 	reg = <0 0xee300000 0 0x2000>;
 	interrupt-parent = <&gic>;
 	interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/gpio/gpio-exar.txt

+Exportable MPIO interface of Exar UART chips
+
+Required properties of the device:
+ - exar,first-pin: first exportable pins (0..15)
+ - ngpios: number of exportable pins (1..16)

Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt

@@ -40,7 +40,7 @@ Optional properties:
 Example for a Mali-T760:
 
 gpu@ffa30000 {
-	compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 	reg = <0xffa30000 0x10000>;
 	interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

Documentation/i2c/i2c-topology

@@ -42,6 +42,10 @@ i2c-arb-gpio-challenge    Parent-locked
 i2c-mux-gpio              Normally parent-locked, mux-locked iff
                           all involved gpio pins are controlled by the
                           same i2c root adapter that they mux.
+i2c-mux-gpmux             Normally parent-locked, mux-locked iff
+                          specified in device-tree.
+i2c-mux-ltc4306           Mux-locked
+i2c-mux-mlxcpld           Parent-locked
 i2c-mux-pca9541           Parent-locked
 i2c-mux-pca954x           Parent-locked
 i2c-mux-pinctrl           Normally parent-locked, mux-locked iff
@@ -50,9 +54,11 @@ i2c-mux-pinctrl           Normally parent-locked, mux-locked iff
 i2c-mux-reg               Parent-locked
 
 In drivers/iio/
+gyro/mpu3050              Mux-locked
 imu/inv_mpu6050/          Mux-locked
 
 In drivers/media/
+dvb-frontends/lgdt3306a   Mux-locked
 dvb-frontends/m88ds3103   Parent-locked
 dvb-frontends/rtl2830     Parent-locked
 dvb-frontends/rtl2832     Mux-locked

Documentation/media/uapi/v4l/subdev-image-processing-crop.svg

@@ -18,11 +18,11 @@
      id="metadata100">
     <rdf:RDF>
       <cc:Work
-         rdf:about="">
-        <dc:format>image/svg+xml</dc:format>
-        <dc:type
-           rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
-        <dc:title />
+	 rdf:about="">
+	<dc:format>image/svg+xml</dc:format>
+	<dc:type
+	   rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
+	<dc:title />
       </cc:Work>
     </rdf:RDF>
   </metadata>

Documentation/media/uapi/v4l/subdev-image-processing-full.svg

@@ -18,11 +18,11 @@
      id="metadata260">
     <rdf:RDF>
       <cc:Work
-         rdf:about="">
-        <dc:format>image/svg+xml</dc:format>
-        <dc:type
-           rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
-        <dc:title />
+	 rdf:about="">
+	<dc:format>image/svg+xml</dc:format>
+	<dc:type
+	   rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
+	<dc:title />
       </cc:Work>
     </rdf:RDF>
   </metadata>

Documentation/media/uapi/v4l/subdev-image-processing-scaling-multi-source.svg

@@ -18,11 +18,11 @@
      id="metadata186">
     <rdf:RDF>
       <cc:Work
-         rdf:about="">
-        <dc:format>image/svg+xml</dc:format>
-        <dc:type
-           rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
-        <dc:title />
+	 rdf:about="">
+	<dc:format>image/svg+xml</dc:format>
+	<dc:type
+	   rdf:resource="http://purl.org/dc/dcmitype/StillImage" />
+	<dc:title />
       </cc:Work>
     </rdf:RDF>
   </metadata>

Documentation/media/uapi/v4l/vidioc-g-fmt.rst

@@ -147,3 +147,9 @@ appropriately. The generic error codes are described at the
 EINVAL
     The struct :c:type:`v4l2_format` ``type`` field is
     invalid or the requested buffer type not supported.
+
+EBUSY
+    The device is busy and cannot change the format. This could be
+    because or the device is streaming or buffers are allocated or
+    queued to the driver. Relevant for :ref:`VIDIOC_S_FMT
+    <VIDIOC_G_FMT>` only.

Documentation/media/v4l-drivers/imx.rst

@@ -607,8 +607,9 @@ References
 
 Authors
 -------
-Steve Longerbeam <steve_longerbeam@mentor.com>
-Philipp Zabel <kernel@pengutronix.de>
-Russell King <linux@armlinux.org.uk>
+
+- Steve Longerbeam <steve_longerbeam@mentor.com>
+- Philipp Zabel <kernel@pengutronix.de>
+- Russell King <linux@armlinux.org.uk>
 
 Copyright (C) 2012-2017 Mentor Graphics Inc.

Documentation/media/v4l-drivers/index.rst

@@ -41,6 +41,7 @@ For more details see the file COPYING in the source distribution of Linux.
 	cx88
 	davinci-vpbe
 	fimc
+	imx
 	ivtv
 	max2175
 	meye

Documentation/power/runtime_pm.txt

@@ -435,7 +435,8 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h:
       PM status to 'suspended' and update its parent's counter of 'active'
       children as appropriate (it is only valid to use this function if
       'power.runtime_error' is set or 'power.disable_depth' is greater than
-      zero)
+      zero); it will fail and return an error code if the device has a child
+      which is active and the 'power.ignore_children' flag is unset
 
   bool pm_runtime_active(struct device *dev);
     - return true if the device's runtime PM status is 'active' or its

MAINTAINERS

@@ -5090,12 +5090,20 @@ M:	Andrew Lunn <andrew@lunn.ch>
 M:	Florian Fainelli <f.fainelli@gmail.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
-F:	include/linux/phy.h
-F:	include/linux/phy_fixed.h
-F:	drivers/net/phy/
+F:	Documentation/ABI/testing/sysfs-bus-mdio
+F:	Documentation/devicetree/bindings/net/mdio*
 F:	Documentation/networking/phy.txt
+F:	drivers/net/phy/
 F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
+F:	include/linux/*mdio*.h
+F:	include/linux/of_net.h
+F:	include/linux/phy.h
+F:	include/linux/phy_fixed.h
+F:	include/linux/platform_data/mdio-gpio.h
+F:	include/trace/events/mdio.h
+F:	include/uapi/linux/mdio.h
+F:	include/uapi/linux/mii.h
 
 EXT2 FILE SYSTEM
 M:	Jan Kara <jack@suse.com>
@@ -14210,6 +14218,12 @@ F:	drivers/watchdog/
 F:	include/linux/watchdog.h
 F:	include/uapi/linux/watchdog.h
 
+WHISKEYCOVE PMIC GPIO DRIVER
+M:	Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
+L:	linux-gpio@vger.kernel.org
+S:	Maintained
+F:	drivers/gpio/gpio-wcove.c
+
 WIIMOTE HID DRIVER
 M:	David Herrmann <dh.herrmann@googlemail.com>
 L:	linux-input@vger.kernel.org

Makefile

 VERSION = 4
 PATCHLEVEL = 13
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc4
 NAME = Fearless Coyote
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -380,7 +380,7 @@ config ARCH_EP93XX
 	bool "EP93xx-based"
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARM_AMBA
-	select ARM_PATCH_PHYS_VIRT
+	imply ARM_PATCH_PHYS_VIRT
 	select ARM_VIC
 	select AUTO_ZRELADDR
 	select CLKDEV_LOOKUP

arch/arm/boot/dts/armada-388-gp.dts

@@ -75,7 +75,7 @@ expander0: pca9555@20 {
 					pinctrl-names = "default";
 					pinctrl-0 = <&pca0_pins>;
 					interrupt-parent = <&gpio0>;
-					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 					gpio-controller;
 					#gpio-cells = <2>;
 					interrupt-controller;
@@ -87,7 +87,7 @@ expander1: pca9555@21 {
 					compatible = "nxp,pca9555";
 					pinctrl-names = "default";
 					interrupt-parent = <&gpio0>;
-					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 					gpio-controller;
 					#gpio-cells = <2>;
 					interrupt-controller;

arch/arm/boot/dts/da850-evm.dts

@@ -301,25 +301,4 @@ &vpif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&vpif_capture_pins>, <&vpif_display_pins>;
 	status = "okay";
-
-	/* VPIF capture port */
-	port@0 {
-		vpif_input_ch0: endpoint@0 {
-			reg = <0>;
-			bus-width = <8>;
-		};
-
-		vpif_input_ch1: endpoint@1 {
-			reg = <1>;
-			bus-width = <8>;
-			data-shift = <8>;
-		};
-	};
-
-	/* VPIF display port */
-	port@1 {
-		vpif_output_ch0: endpoint {
-			bus-width = <8>;
-		};
-	};
 };

arch/arm/boot/dts/da850-lcdk.dts

@@ -318,11 +318,4 @@ &vpif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&vpif_capture_pins>;
 	status = "okay";
-
-	/* VPIF capture port */
-	port {
-		vpif_ch0: endpoint {
-			  bus-width = <8>;
-		};
-	};
 };

arch/arm/boot/dts/dm816x.dtsi

@@ -145,7 +145,7 @@ edma: edma@49000000 {
 		};
 
 		elm: elm@48080000 {
-			compatible = "ti,816-elm";
+			compatible = "ti,am3352-elm";
 			ti,hwmods = "elm";
 			reg = <0x48080000 0x2000>;
 			interrupts = <4>;

arch/arm/boot/dts/dra71-evm.dts

@@ -190,7 +190,7 @@ dp83867_0: ethernet-phy@2 {
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
-		ti,impedance-control = <0x1f>;
+		ti,min-output-impedance;
 	};
 
 	dp83867_1: ethernet-phy@3 {
@@ -198,7 +198,7 @@ dp83867_1: ethernet-phy@3 {
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
-		ti,impedance-control = <0x1f>;
+		ti,min-output-impedance;
 	};
 };
 

arch/arm/boot/dts/exynos4.dtsi

@@ -59,6 +59,9 @@ clock_audss: clock-controller@03810000 {
 		compatible = "samsung,exynos4210-audss-clock";
 		reg = <0x03810000 0x0C>;
 		#clock-cells = <1>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+			 <&clock CLK_SCLK_AUDIO0>, <&clock CLK_SCLK_AUDIO0>;
+		clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
 	};
 
 	i2s0: i2s@03830000 {

arch/arm/boot/dts/rk3288.dtsi

@@ -1126,8 +1126,8 @@ hdmi_in_vopl: endpoint@1 {
 		};
 	};
 
-	gpu: mali@ffa30000 {
-		compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	gpu: gpu@ffa30000 {
+		compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 		reg = <0xffa30000 0x10000>;
 		interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -394,7 +394,7 @@ timer@01c20c00 {
 		emac: ethernet@1c30000 {
 			compatible = "allwinner,sun8i-h3-emac";
 			syscon = <&syscon>;
-			reg = <0x01c30000 0x104>;
+			reg = <0x01c30000 0x10000>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			resets = <&ccu RST_BUS_EMAC>;