Commit 9281b16c authored by James Bottomley's avatar James Bottomley Committed by Jeff Garzik

pata_cm64x: fix boot crash on parisc

The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them.  pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).

Fix this by porting the CNTRL register port detection logic from IDE
cmd64x.  In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: default avatarJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: default avatarJeff Garzik <jgarzik@pobox.com>
parent 5f6f12cc
......@@ -41,6 +41,9 @@
enum {
CFR = 0x50,
CFR_INTR_CH0 = 0x04,
CNTRL = 0x51,
CNTRL_CH0 = 0x04,
CNTRL_CH1 = 0x08,
CMDTIM = 0x52,
ARTTIM0 = 0x53,
DRWTIM0 = 0x54,
......@@ -328,9 +331,19 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cmd648_port_ops
}
};
const struct ata_port_info *ppi[] = { &cmd_info[id->driver_data], NULL };
u8 mrdmode;
const struct ata_port_info *ppi[] = {
&cmd_info[id->driver_data],
&cmd_info[id->driver_data],
NULL
};
u8 mrdmode, reg;
int rc;
struct pci_dev *bridge = pdev->bus->self;
/* mobility split bridges don't report enabled ports correctly */
int port_ok = !(bridge && bridge->vendor ==
PCI_VENDOR_ID_MOBILITY_ELECTRONICS);
/* all (with exceptions below) apart from 643 have CNTRL_CH0 bit */
int cntrl_ch0_ok = (id->driver_data != 0);
rc = pcim_enable_device(pdev);
if (rc)
......@@ -341,11 +354,18 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (pdev->device == PCI_DEVICE_ID_CMD_646) {
/* Does UDMA work ? */
if (pdev->revision > 4)
if (pdev->revision > 4) {
ppi[0] = &cmd_info[2];
ppi[1] = &cmd_info[2];
}
/* Early rev with other problems ? */
else if (pdev->revision == 1)
else if (pdev->revision == 1) {
ppi[0] = &cmd_info[3];
ppi[1] = &cmd_info[3];
}
/* revs 1,2 have no CNTRL_CH0 */
if (pdev->revision < 3)
cntrl_ch0_ok = 0;
}
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
......@@ -354,6 +374,20 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
mrdmode |= 0x02; /* Memory read line enable */
pci_write_config_byte(pdev, MRDMODE, mrdmode);
/* check for enabled ports */
pci_read_config_byte(pdev, CNTRL, &reg);
if (!port_ok)
dev_printk(KERN_NOTICE, &pdev->dev, "Mobility Bridge detected, ignoring CNTRL port enable/disable\n");
if (port_ok && cntrl_ch0_ok && !(reg & CNTRL_CH0)) {
dev_printk(KERN_NOTICE, &pdev->dev, "Primary port is disabled\n");
ppi[0] = &ata_dummy_port_info;
}
if (port_ok && !(reg & CNTRL_CH1)) {
dev_printk(KERN_NOTICE, &pdev->dev, "Secondary port is disabled\n");
ppi[1] = &ata_dummy_port_info;
}
/* Force PIO 0 here.. */
/* PPC specific fixup copied from old driver */
......
......@@ -608,6 +608,8 @@
#define PCI_DEVICE_ID_MATROX_G550 0x2527
#define PCI_DEVICE_ID_MATROX_VIA 0x4536
#define PCI_VENDOR_ID_MOBILITY_ELECTRONICS 0x14f2
#define PCI_VENDOR_ID_CT 0x102c
#define PCI_DEVICE_ID_CT_69000 0x00c0
#define PCI_DEVICE_ID_CT_65545 0x00d8
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment