Merge HEAD from master.kernel.org:/home/rmk/linux-2.6-serial.git

include/linux/8250_pci.h

-int pci_siig10x_fn(struct pci_dev *dev, int enable);
-int pci_siig20x_fn(struct pci_dev *dev, int enable);
+/*
+ * Definitions for PCI support.
+ */
+#define FL_BASE_MASK		0x0007
+#define FL_BASE0		0x0000
+#define FL_BASE1		0x0001
+#define FL_BASE2		0x0002
+#define FL_BASE3		0x0003
+#define FL_BASE4		0x0004
+#define FL_GET_BASE(x)		(x & FL_BASE_MASK)
+
+/* Use successive BARs (PCI base address registers),
+   else use offset into some specified BAR */
+#define FL_BASE_BARS		0x0008
+
+/* do not assign an irq */
+#define FL_NOIRQ		0x0080
+
+/* Use the Base address register size to cap number of ports */
+#define FL_REGION_SZ_CAP	0x0100
+
+struct pciserial_board {
+	unsigned int flags;
+	unsigned int num_ports;
+	unsigned int base_baud;
+	unsigned int uart_offset;
+	unsigned int reg_shift;
+	unsigned int first_offset;
+};
+
+struct serial_private;
+
+struct serial_private *
+pciserial_init_ports(struct pci_dev *dev, struct pciserial_board *board);
+void pciserial_remove_ports(struct serial_private *priv);
+void pciserial_suspend_ports(struct serial_private *priv);
+void pciserial_resume_ports(struct serial_private *priv);

include/linux/serialP.h

@@ -140,44 +140,4 @@ struct rs_multiport_struct {
 #define ALPHA_KLUDGE_MCR 0
 #endif
 
-/*
- * Definitions for PCI support.
- */
-#define SPCI_FL_BASE_MASK	0x0007
-#define SPCI_FL_BASE0	0x0000
-#define SPCI_FL_BASE1	0x0001
-#define SPCI_FL_BASE2	0x0002
-#define SPCI_FL_BASE3	0x0003
-#define SPCI_FL_BASE4	0x0004
-#define SPCI_FL_GET_BASE(x)	(x & SPCI_FL_BASE_MASK)
-
-#define SPCI_FL_IRQ_MASK       (0x0007 << 4)
-#define SPCI_FL_IRQBASE0       (0x0000 << 4)
-#define SPCI_FL_IRQBASE1       (0x0001 << 4)
-#define SPCI_FL_IRQBASE2       (0x0002 << 4)
-#define SPCI_FL_IRQBASE3       (0x0003 << 4)
-#define SPCI_FL_IRQBASE4       (0x0004 << 4)
-#define SPCI_FL_GET_IRQBASE(x)        ((x & SPCI_FL_IRQ_MASK) >> 4)
-
-/* Use successive BARs (PCI base address registers), 
-   else use offset into some specified BAR */
-#define SPCI_FL_BASE_TABLE	0x0100
-
-/* Use successive entries in the irq resource table */
-#define SPCI_FL_IRQ_TABLE	0x0200
-
-/* Use the irq resource table instead of dev->irq */
-#define SPCI_FL_IRQRESOURCE	0x0400
-
-/* Use the Base address register size to cap number of ports */
-#define SPCI_FL_REGION_SZ_CAP	0x0800
-
-/* Do not use irq sharing for this device */
-#define SPCI_FL_NO_SHIRQ	0x1000
-
-/* This is a PNP device */
-#define SPCI_FL_ISPNP		0x2000
-
-#define SPCI_FL_PNPDEFAULT	(SPCI_FL_IRQRESOURCE|SPCI_FL_ISPNP)
-
 #endif /* _LINUX_SERIAL_H */