Commit 9823adf6 authored by Krzysztof Helt's avatar Krzysztof Helt Committed by Jaroslav Kysela

[ALSA] This simplifies and fixes waiting loops of the mce_down()

function after Trent Piepho's patch for AD1848.
It also makes busy_wait() function call not atomic.
Signed-off-by: default avatarKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: default avatarTakashi Iwai <tiwai@suse.de>
Signed-off-by: default avatarJaroslav Kysela <perex@perex.cz>
parent 0895e91d
......@@ -400,65 +400,44 @@ static void snd_cs4231_mce_up(struct snd_cs4231 *chip)
static void snd_cs4231_mce_down(struct snd_cs4231 *chip)
{
unsigned long flags;
unsigned long end_time;
int timeout;
unsigned long flags, timeout;
int reg;
spin_lock_irqsave(&chip->lock, flags);
snd_cs4231_busy_wait(chip);
spin_lock_irqsave(&chip->lock, flags);
#ifdef CONFIG_SND_DEBUG
if (__cs4231_readb(chip, CS4231U(chip, REGSEL)) & CS4231_INIT)
snd_printdd("mce_down [%p] - auto calibration time out (0)\n",
CS4231U(chip, REGSEL));
#endif
chip->mce_bit &= ~CS4231_MCE;
timeout = __cs4231_readb(chip, CS4231U(chip, REGSEL));
__cs4231_writeb(chip, chip->mce_bit | (timeout & 0x1f),
reg = __cs4231_readb(chip, CS4231U(chip, REGSEL));
__cs4231_writeb(chip, chip->mce_bit | (reg & 0x1f),
CS4231U(chip, REGSEL));
if (timeout == 0x80)
snd_printdd("mce_down [%p]: serious init problem - "
"codec still busy\n",
chip->port);
if ((timeout & CS4231_MCE) == 0) {
if (reg == 0x80)
snd_printdd("mce_down [%p]: serious init problem "
"- codec still busy\n", chip->port);
if ((reg & CS4231_MCE) == 0) {
spin_unlock_irqrestore(&chip->lock, flags);
return;
}
/*
* Wait for (possible -- during init auto-calibration may not be set)
* calibration process to start. Needs upto 5 sample periods on AD1848
* which at the slowest possible rate of 5.5125 kHz means 907 us.
* Wait for auto-calibration (AC) process to finish, i.e. ACI to go low.
*/
msleep(1);
/* check condition up to 250ms */
end_time = jiffies + msecs_to_jiffies(250);
while (snd_cs4231_in(chip, CS4231_TEST_INIT) &
CS4231_CALIB_IN_PROGRESS) {
timeout = jiffies + msecs_to_jiffies(250);
do {
spin_unlock_irqrestore(&chip->lock, flags);
if (time_after(jiffies, end_time)) {
snd_printk("mce_down - "
"auto calibration time out (2)\n");
return;
}
msleep(1);
spin_lock_irqsave(&chip->lock, flags);
}
/* check condition up to 100ms */
end_time = jiffies + msecs_to_jiffies(100);
while (__cs4231_readb(chip, CS4231U(chip, REGSEL)) & CS4231_INIT) {
spin_unlock_irqrestore(&chip->lock, flags);
if (time_after(jiffies, end_time)) {
snd_printk("mce_down - "
"auto calibration time out (3)\n");
return;
}
msleep(1);
spin_lock_irqsave(&chip->lock, flags);
}
reg = snd_cs4231_in(chip, CS4231_TEST_INIT);
reg &= CS4231_CALIB_IN_PROGRESS;
} while (reg && time_before(jiffies, timeout));
spin_unlock_irqrestore(&chip->lock, flags);
if (reg)
snd_printk(KERN_ERR
"mce_down - auto calibration time out (2)\n");
}
static void snd_cs4231_advance_dma(struct cs4231_dma_control *dma_cont,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment