Commit a886bd92 authored by Peter Chen's avatar Peter Chen Committed by Greg Kroah-Hartman

usb: common: otg-fsm: only signal connect after switching to peripheral

We should signal connect (pull up dp) after we have already
at peripheral mode, otherwise, the dp may be toggled due to
we reset controller or do disconnect during the initialization
for peripheral, then, the host may be confused during the
enumeration, eg, it finds the reset can't succeed, but the
device is still there, see below error message.

hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: cannot reset port 1 (err = -32)
hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 1-0:1.0: unable to enumerate USB device on port 1

Fixes: the issue existed when the otg fsm code was added.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: default avatarPeter Chen <peter.chen@freescale.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent bda13e35
...@@ -150,9 +150,9 @@ static int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state) ...@@ -150,9 +150,9 @@ static int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state)
break; break;
case OTG_STATE_B_PERIPHERAL: case OTG_STATE_B_PERIPHERAL:
otg_chrg_vbus(fsm, 0); otg_chrg_vbus(fsm, 0);
otg_loc_conn(fsm, 1);
otg_loc_sof(fsm, 0); otg_loc_sof(fsm, 0);
otg_set_protocol(fsm, PROTO_GADGET); otg_set_protocol(fsm, PROTO_GADGET);
otg_loc_conn(fsm, 1);
break; break;
case OTG_STATE_B_WAIT_ACON: case OTG_STATE_B_WAIT_ACON:
otg_chrg_vbus(fsm, 0); otg_chrg_vbus(fsm, 0);
...@@ -213,10 +213,10 @@ static int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state) ...@@ -213,10 +213,10 @@ static int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state)
break; break;
case OTG_STATE_A_PERIPHERAL: case OTG_STATE_A_PERIPHERAL:
otg_loc_conn(fsm, 1);
otg_loc_sof(fsm, 0); otg_loc_sof(fsm, 0);
otg_set_protocol(fsm, PROTO_GADGET); otg_set_protocol(fsm, PROTO_GADGET);
otg_drv_vbus(fsm, 1); otg_drv_vbus(fsm, 1);
otg_loc_conn(fsm, 1);
otg_add_timer(fsm, A_BIDL_ADIS); otg_add_timer(fsm, A_BIDL_ADIS);
break; break;
case OTG_STATE_A_WAIT_VFALL: case OTG_STATE_A_WAIT_VFALL:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment