Commit aef34b48 authored by Chunfeng Yun's avatar Chunfeng Yun Committed by Greg Kroah-Hartman

usb: mtu3: remove QMU checksum

The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: default avatarChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 1e3af5df
......@@ -592,8 +592,6 @@ static void mtu3_regs_init(struct mtu3 *mtu)
mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
/* U2/U3 detected by HW */
mtu3_writel(mbase, U3D_DEVICE_CONF, 0);
/* enable QMU 16B checksum */
mtu3_setbits(mbase, U3D_QCR0, QMU_CS16B_EN);
/* vbus detected by HW */
mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
}
......
......@@ -154,27 +154,6 @@ void mtu3_gpd_ring_free(struct mtu3_ep *mep)
memset(ring, 0, sizeof(*ring));
}
/*
* calculate check sum of a gpd or bd
* add "noinline" and "mb" to prevent wrong calculation
*/
static noinline u8 qmu_calc_checksum(u8 *data)
{
u8 chksum = 0;
int i;
data[1] = 0x0; /* set checksum to 0 */
mb(); /* ensure the gpd/bd is really up-to-date */
for (i = 0; i < QMU_CHECKSUM_LEN; i++)
chksum += data[i];
/* Default: HWO=1, @flag[bit0] */
chksum += 1;
return 0xFF - chksum;
}
void mtu3_qmu_resume(struct mtu3_ep *mep)
{
struct mtu3 *mtu = mep->mtu;
......@@ -260,7 +239,6 @@ static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
if (req->zero)
gpd->ext_flag |= GPD_EXT_FLAG_ZLP;
gpd->chksum = qmu_calc_checksum((u8 *)gpd);
gpd->flag |= GPD_FLAGS_HWO;
mreq->gpd = gpd;
......@@ -295,7 +273,6 @@ static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
gpd->next_gpd = cpu_to_le32(lower_32_bits(enq_dma));
ext_addr |= GPD_EXT_NGP(upper_32_bits(enq_dma));
gpd->rx_ext_addr = cpu_to_le16(ext_addr);
gpd->chksum = qmu_calc_checksum((u8 *)gpd);
gpd->flag |= GPD_FLAGS_HWO;
mreq->gpd = gpd;
......@@ -323,7 +300,6 @@ int mtu3_qmu_start(struct mtu3_ep *mep)
/* set QMU start address */
write_txq_start_addr(mbase, epnum, ring->dma);
mtu3_setbits(mbase, MU3D_EP_TXCR0(epnum), TX_DMAREQEN);
mtu3_setbits(mbase, U3D_QCR0, QMU_TX_CS_EN(epnum));
/* send zero length packet according to ZLP flag in GPD */
mtu3_setbits(mbase, U3D_QCR1, QMU_TX_ZLP(epnum));
mtu3_writel(mbase, U3D_TQERRIESR0,
......@@ -338,7 +314,6 @@ int mtu3_qmu_start(struct mtu3_ep *mep)
} else {
write_rxq_start_addr(mbase, epnum, ring->dma);
mtu3_setbits(mbase, MU3D_EP_RXCR0(epnum), RX_DMAREQEN);
mtu3_setbits(mbase, U3D_QCR0, QMU_RX_CS_EN(epnum));
/* don't expect ZLP */
mtu3_clrbits(mbase, U3D_QCR3, QMU_RX_ZLP(epnum));
/* move to next GPD when receive ZLP */
......@@ -441,7 +416,6 @@ static void qmu_tx_zlp_error_handler(struct mtu3 *mtu, u8 epnum)
/* by pass the current GDP */
gpd_current->flag |= GPD_FLAGS_BPS;
gpd_current->chksum = qmu_calc_checksum((u8 *)gpd_current);
gpd_current->flag |= GPD_FLAGS_HWO;
/*enable DMAREQEN, switch back to QMU mode */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment