Commit b0ddc910 authored by Joel Stanley's avatar Joel Stanley

ARM: config: multi_v5: Enable ASPEED drivers

This enables the devices used in the AST2400 family of BMC SoCs:

 - VUART
 - SPI NOR
 - LPC controller
 - LPC snoop (port 80)
 - Ethernet
 - GPIO
 - ADC
 - I2C
 - Random number generator
 - IPMI KCS
 - IPMI BT
 - Fan/Tach
Acked-by: default avatarAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: default avatarJoel Stanley <joel@jms.id.au>
parent fc2a325b
......@@ -90,10 +90,14 @@ CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
CONFIG_MTD_NAND_ORION=y
CONFIG_MTD_SPI_NOR=y
CONFIG_SPI_ASPEED_SMC=y
CONFIG_MTD_UBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_ATMEL_TCLIB=y
CONFIG_ATMEL_SSC=m
CONFIG_ASPEED_LPC_CTRL=m
CONFIG_ASPEED_LPC_SNOOP=m
CONFIG_EEPROM_AT24=y
# CONFIG_SCSI_PROC_FS is not set
CONFIG_BLK_DEV_SD=y
......@@ -107,6 +111,7 @@ CONFIG_NET_DSA_MV88E6060=y
CONFIG_NET_DSA_MV88E6XXX=y
CONFIG_MACB=y
CONFIG_DM9000=y
CONFIG_FTGMAC100=m
CONFIG_MV643XX_ETH=y
CONFIG_R8169=y
CONFIG_DAVICOM_PHY=y
......@@ -128,16 +133,20 @@ CONFIG_SERIAL_8250_NR_UARTS=6
CONFIG_SERIAL_8250_RUNTIME_UARTS=6
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_ASPEED_VUART=m
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_SERIAL_ATMEL_TTYAT=y
CONFIG_SERIAL_IMX=y
CONFIG_SERIAL_IMX_CONSOLE=y
CONFIG_ASPEED_KCS_IPMI_BMC=m
CONFIG_ASPEED_BT_IPMI_BMC=m
CONFIG_HW_RANDOM=y
CONFIG_I2C=y
CONFIG_HW_RANDOM_TIMERIOMEM=m
# CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_ASPEED=m
CONFIG_I2C_AT91=y
CONFIG_I2C_IMX=y
CONFIG_I2C_MV64XXX=y
......@@ -146,10 +155,12 @@ CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
CONFIG_SPI_IMX=y
CONFIG_SPI_ORION=y
CONFIG_GPIO_ASPEED=m
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_GPIO=y
CONFIG_POWER_RESET_QNAP=y
CONFIG_SENSORS_ADT7475=y
CONFIG_SENSORS_ASPEED=y
CONFIG_SENSORS_G762=y
CONFIG_SENSORS_LM63=y
CONFIG_SENSORS_LM75=y
......@@ -240,6 +251,7 @@ CONFIG_MV_XOR=y
CONFIG_STAGING=y
CONFIG_FB_XGI=y
CONFIG_IIO=m
CONFIG_ASPEED_ADC=m
CONFIG_AT91_ADC=m
CONFIG_PWM=y
CONFIG_PWM_ATMEL=m
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment