[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c

There is no reason to have power control in a separate file from the
board setup code.  Merge it back into the board setup file and remove
superfluous header includes.

--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-ixp4xx/Makefile

@@ -24,7 +24,7 @@ obj-$(CONFIG_MACH_IXDPG425)	+= coyote-setup.o
 obj-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-setup.o
 obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
 obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.o
-obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o nas100d-power.o
+obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o
 obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o dsmg600-power.o
 obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
 obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o

arch/arm/mach-ixp4xx/nas100d-power.c

-/*
- * arch/arm/mach-ixp4xx/nas100d-power.c
- *
- * NAS 100d Power/Reset driver
- *
- * Copyright (C) 2005 Tower Technologies
- *
- * based on nas100d-io.c
- *  Copyright (C) 2004 Karen Spearel
- *
- * Author: Alessandro Zummo <a.zummo@towertech.it>
- * Maintainers: http://www.nslu2-linux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <linux/reboot.h>
-#include <linux/jiffies.h>
-#include <linux/timer.h>
-
-#include <asm/gpio.h>
-#include <asm/mach-types.h>
-
-/* This is used to make sure the power-button pusher is serious.  The button
- * must be held until the value of this counter reaches zero.
- */
-static int power_button_countdown;
-
-/* Must hold the button down for at least this many counts to be processed */
-#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
-
-static void nas100d_power_handler(unsigned long data);
-static DEFINE_TIMER(nas100d_power_timer, nas100d_power_handler, 0, 0);
-
-static void nas100d_power_handler(unsigned long data)
-{
-	/* This routine is called twice per second to check the
-	 * state of the power button.
-	 */
-
-	if (gpio_get_value(NAS100D_PB_GPIO)) {
-
-		/* IO Pin is 1 (button pushed) */
-		if (power_button_countdown > 0)
-			power_button_countdown--;
-
-	} else {
-
-		/* Done on button release, to allow for auto-power-on mods. */
-		if (power_button_countdown == 0) {
-			/* Signal init to do the ctrlaltdel action,
-			 * this will bypass init if it hasn't started
-			 * and do a kernel_restart.
-			 */
-			ctrl_alt_del();
-
-			/* Change the state of the power LED to "blink" */
-			gpio_line_set(NAS100D_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
-		} else {
-			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-		}
-	}
-
-	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
-}
-
-static irqreturn_t nas100d_reset_handler(int irq, void *dev_id)
-{
-	/* This is the paper-clip reset, it shuts the machine down directly. */
-	machine_power_off();
-
-	return IRQ_HANDLED;
-}
-
-static int __init nas100d_power_init(void)
-{
-	if (!(machine_is_nas100d()))
-		return 0;
-
-	set_irq_type(gpio_to_irq(NAS100D_RB_GPIO), IRQT_LOW);
-
-	if (request_irq(gpio_to_irq(NAS100D_RB_GPIO), &nas100d_reset_handler,
-		IRQF_DISABLED, "NAS100D reset button", NULL) < 0) {
-
-		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
-			gpio_to_irq(NAS100D_RB_GPIO));
-
-		return -EIO;
-	}
-
-	/* The power button on the Iomega NAS100d is on GPIO 14, but
-	 * it cannot handle interrupts on that GPIO line.  So we'll
-	 * have to poll it with a kernel timer.
-	 */
-
-	/* Make sure that the power button GPIO is set up as an input */
-	gpio_line_config(NAS100D_PB_GPIO, IXP4XX_GPIO_IN);
-
-	/* Set the initial value for the power button IRQ handler */
-	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
-	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
-
-	return 0;
-}
-
-static void __exit nas100d_power_exit(void)
-{
-	if (!(machine_is_nas100d()))
-		return;
-
-	del_timer_sync(&nas100d_power_timer);
-
-	free_irq(gpio_to_irq(NAS100D_RB_GPIO), NULL);
-}
-
-module_init(nas100d_power_init);
-module_exit(nas100d_power_exit);
-
-MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
-MODULE_DESCRIPTION("NAS100D Power/Reset driver");
-MODULE_LICENSE("GPL");

arch/arm/mach-ixp4xx/nas100d-setup.c

@@ -3,8 +3,14 @@
  *
  * NAS 100d board-setup
  *
- * based ixdp425-setup.c:
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ *
+ * based on ixdp425-setup.c:
  *      Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nas100d-power.c:
+ *	Copyright (C) 2005 Tower Technologies
+ * based on nas100d-io.c
+ *	Copyright (C) 2004 Karen Spearel
  *
  * Author: Alessandro Zummo <a.zummo@towertech.it>
  * Author: Rod Whitby <rod@whitby.id.au>
@@ -13,10 +19,13 @@
  */
 
 #include <linux/if_ether.h>
-#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/jiffies.h>
+#include <linux/timer.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
 #include <linux/leds.h>
+#include <linux/reboot.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
@@ -24,6 +33,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 
 static struct flash_platform_data nas100d_flash_data = {
 	.map_name		= "cfi_probe",
@@ -168,6 +178,57 @@ static void nas100d_power_off(void)
 	gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
 }
 
+/* This is used to make sure the power-button pusher is serious.  The button
+ * must be held until the value of this counter reaches zero.
+ */
+static int power_button_countdown;
+
+/* Must hold the button down for at least this many counts to be processed */
+#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
+
+static void nas100d_power_handler(unsigned long data);
+static DEFINE_TIMER(nas100d_power_timer, nas100d_power_handler, 0, 0);
+
+static void nas100d_power_handler(unsigned long data)
+{
+	/* This routine is called twice per second to check the
+	 * state of the power button.
+	 */
+
+	if (gpio_get_value(NAS100D_PB_GPIO)) {
+
+		/* IO Pin is 1 (button pushed) */
+		if (power_button_countdown > 0)
+			power_button_countdown--;
+
+	} else {
+
+		/* Done on button release, to allow for auto-power-on mods. */
+		if (power_button_countdown == 0) {
+			/* Signal init to do the ctrlaltdel action,
+			 * this will bypass init if it hasn't started
+			 * and do a kernel_restart.
+			 */
+			ctrl_alt_del();
+
+			/* Change the state of the power LED to "blink" */
+			gpio_line_set(NAS100D_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+		} else {
+			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+		}
+	}
+
+	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
+}
+
+static irqreturn_t nas100d_reset_handler(int irq, void *dev_id)
+{
+	/* This is the paper-clip reset, it shuts the machine down directly. */
+	machine_power_off();
+
+	return IRQ_HANDLED;
+}
+
 static void __init nas100d_init(void)
 {
 	DECLARE_MAC_BUF(mac_buf);
@@ -183,8 +244,6 @@ static void __init nas100d_init(void)
 	nas100d_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
-	pm_power_off = nas100d_power_off;
-
 	i2c_register_board_info(0, nas100d_i2c_board_info,
 				ARRAY_SIZE(nas100d_i2c_board_info));
 
@@ -197,6 +256,29 @@ static void __init nas100d_init(void)
 
 	platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
 
+	pm_power_off = nas100d_power_off;
+
+	if (request_irq(gpio_to_irq(NAS100D_RB_GPIO), &nas100d_reset_handler,
+		IRQF_DISABLED | IRQF_TRIGGER_LOW,
+		"NAS100D reset button", NULL) < 0) {
+
+		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+			gpio_to_irq(NAS100D_RB_GPIO));
+	}
+
+	/* The power button on the Iomega NAS100d is on GPIO 14, but
+	 * it cannot handle interrupts on that GPIO line.  So we'll
+	 * have to poll it with a kernel timer.
+	 */
+
+	/* Make sure that the power button GPIO is set up as an input */
+	gpio_line_config(NAS100D_PB_GPIO, IXP4XX_GPIO_IN);
+
+	/* Set the initial value for the power button IRQ handler */
+	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
+
 	/*
 	 * Map in a portion of the flash and read the MAC address.
 	 * Since it is stored in BE in the flash itself, we need to