Merge tag '64bit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC 64-bit changes and additions from Olof Johansson:
 "The 64-bit set of updates this release cycle adds support for three
  new platforms:

   - Samsunc Exynos 7
   - Freescale LS2085a
   - Mediatek MT8173

  For all these, the changes mostly consititude additions of DT
  contents, but also some Kconfig entries to allow dependency/selection
  of drivers per-platform, etc"

* tag '64bit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: Kconfig: clean up two no-op Kconfig options from CONFIG_ARCH_TEGRA*
  arm64: Fix sort of platform Kconfig entries
  arm64: Add support for FSL's LS2085A SoC in Kconfig and defconfig
  arm64: Add DTS support for FSL's LS2085A SoC
  arm64: mediatek: Add MT8173 SoC Kconfig and defconfig
  arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile
  Document: DT: Add bindings for mediatek MT8173 SoC Platform
  arm64: Add Tegra132 support
  arm64: Enable ARMv8 based exynos7 SoC support
  arm64: dts: Add nodes for mmc, i2c, rtc, watchdog, adc on exynos7
  arm64: dts: Add PMU DT node for exynos7 SoC
  arm64: dts: Add initial pinctrl support to exynos7
  arm64: dts: Add initial device tree support for exynos7

Documentation/devicetree/bindings/arm/mediatek.txt

@@ -9,6 +9,7 @@ compatible: Must contain one of
    "mediatek,mt6592"
    "mediatek,mt8127"
    "mediatek,mt8135"
+   "mediatek,mt8173"
 
 
 Supported boards:
@@ -25,3 +26,6 @@ Supported boards:
 - MTK mt8135 tablet EVB:
     Required root node properties:
       - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135";
+- MTK mt8173 tablet EVB:
+    Required root node properties:
+      - compatible = "mediatek,mt8173-evb", "mediatek,mt8173";

Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt

@@ -5,6 +5,7 @@ interrupt.
 
 Required properties:
 - compatible: should be one of:
+	"mediatek,mt8173-sysirq"
 	"mediatek,mt8135-sysirq"
 	"mediatek,mt8127-sysirq"
 	"mediatek,mt6592-sysirq"

Documentation/devicetree/bindings/arm/samsung/pmu.txt

@@ -10,6 +10,7 @@ Properties:
 		   - "samsung,exynos5260-pmu" - for Exynos5260 SoC.
 		   - "samsung,exynos5410-pmu" - for Exynos5410 SoC,
 		   - "samsung,exynos5420-pmu" - for Exynos5420 SoC.
+		   - "samsung,exynos7-pmu" - for Exynos7 SoC.
 		second value must be always "syscon".
 
  - reg : offset and length of the register set.

Documentation/devicetree/bindings/serial/mtk-uart.txt

@@ -4,9 +4,11 @@ Required properties:
 - compatible should contain:
   * "mediatek,mt8135-uart" for MT8135 compatible UARTS
   * "mediatek,mt8127-uart" for MT8127 compatible UARTS
+  * "mediatek,mt8173-uart" for MT8173 compatible UARTS
   * "mediatek,mt6589-uart" for MT6589 compatible UARTS
   * "mediatek,mt6582-uart" for MT6582 compatible UARTS
-  * "mediatek,mt6577-uart" for all compatible UARTS (MT6589, MT6582, MT6577)
+  * "mediatek,mt6577-uart" for all compatible UARTS (MT8173, MT6589, MT6582, 
+	MT6577)
 
 - reg: The base address of the UART register bank.
 

arch/arm64/Kconfig

@@ -149,11 +149,65 @@ source "kernel/Kconfig.freezer"
 
 menu "Platform selection"
 
+config ARCH_EXYNOS
+	bool
+	help
+	  This enables support for Samsung Exynos SoC family
+
+config ARCH_EXYNOS7
+	bool "ARMv8 based Samsung Exynos7"
+	select ARCH_EXYNOS
+	select COMMON_CLK_SAMSUNG
+	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select HAVE_S3C_RTC if RTC_CLASS
+	select PINCTRL
+	select PINCTRL_EXYNOS
+
+	help
+	  This enables support for Samsung Exynos7 SoC family
+
+config ARCH_FSL_LS2085A
+	bool "Freescale LS2085A SOC"
+	help
+	  This enables support for Freescale LS2085A SOC.
+
+config ARCH_MEDIATEK
+	bool "Mediatek MT65xx & MT81xx ARMv8 SoC"
+	select ARM_GIC
+	help
+	  Support for Mediatek MT65xx & MT81xx ARMv8 SoCs
+
 config ARCH_SEATTLE
 	bool "AMD Seattle SoC Family"
 	help
 	  This enables support for AMD Seattle SOC Family
 
+config ARCH_TEGRA
+	bool "NVIDIA Tegra SoC Family"
+	select ARCH_HAS_RESET_CONTROLLER
+	select ARCH_REQUIRE_GPIOLIB
+	select CLKDEV_LOOKUP
+	select CLKSRC_MMIO
+	select CLKSRC_OF
+	select GENERIC_CLOCKEVENTS
+	select HAVE_CLK
+	select PINCTRL
+	select RESET_CONTROLLER
+	help
+	  This enables support for the NVIDIA Tegra SoC family.
+
+config ARCH_TEGRA_132_SOC
+	bool "NVIDIA Tegra132 SoC"
+	depends on ARCH_TEGRA
+	select PINCTRL_TEGRA124
+	select USB_ULPI if USB_PHY
+	select USB_ULPI_VIEWPORT if USB_PHY
+	help
+	  Enable support for NVIDIA Tegra132 SoC, based on the Denver
+	  ARMv8 CPU.  The Tegra132 SoC is similar to the Tegra124 SoC,
+	  but contains an NVIDIA Denver CPU complex in place of
+	  Tegra124's "4+1" Cortex-A15 CPU complex.
+
 config ARCH_THUNDER
 	bool "Cavium Inc. Thunder SoC Family"
 	help

arch/arm64/boot/dts/Makefile

@@ -2,5 +2,8 @@ dts-dirs += amd
 dts-dirs += apm
 dts-dirs += arm
 dts-dirs += cavium
+dts-dirs += exynos
+dts-dirs += freescale
+dts-dirs += mediatek
 
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/exynos/Makefile

+dtb-$(CONFIG_ARCH_EXYNOS7) += exynos7-espresso.dtb
+
+always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
+clean-files	:= *.dtb

arch/arm64/boot/dts/exynos/exynos7-espresso.dts

+/*
+ * SAMSUNG Exynos7 Espresso board device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos7.dtsi"
+
+/ {
+	model = "Samsung Exynos7 Espresso board based on EXYNOS7";
+	compatible = "samsung,exynos7-espresso", "samsung,exynos7";
+
+	aliases {
+		serial0 = &serial_2;
+		mshc0 = &mmc_0;
+		mshc2 = &mmc_2;
+	};
+
+	chosen {
+		linux,stdout-path = &serial_2;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x0 0xC0000000>;
+	};
+};
+
+&fin_pll {
+	clock-frequency = <24000000>;
+};
+
+&serial_2 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	cap-mmc-highspeed;
+	non-removable;
+	card-detect-delay = <200>;
+	clock-frequency = <800000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_qrdy &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+	bus-width = <8>;
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+	bus-width = <4>;
+	disable-wp;
+};

arch/arm64/boot/dts/freescale/Makefile

+dtb-$(CONFIG_ARCH_FSL_LS2085A) += fsl-ls2085a-simu.dtb
+ 
+always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
+clean-files	:= *.dtb

arch/arm64/boot/dts/freescale/fsl-ls2085a-simu.dts

+/*
+ * Device Tree file for Freescale LS2085a software Simulator model
+ *
+ * Copyright (C) 2014, Freescale Semiconductor
+ *
+ * Bhupesh Sharma <bhupesh.sharma@freescale.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this library; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+/include/ "fsl-ls2085a.dtsi"
+
+/ {
+	model = "Freescale Layerscape 2085a software Simulator model";
+	compatible = "fsl,ls2085a-simu", "fsl,ls2085a";
+
+	ethernet@2210000 {
+		compatible = "smsc,lan91c111";
+		reg = <0x0 0x2210000 0x0 0x100>;
+		interrupts = <0 58 0x1>;
+	};
+};

arch/arm64/boot/dts/freescale/fsl-ls2085a.dtsi

+/*
+ * Device Tree Include file for Freescale Layerscape-2085A family SoC.
+ *
+ * Copyright (C) 2014, Freescale Semiconductor
+ *
+ * Bhupesh Sharma <bhupesh.sharma@freescale.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this library; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+	compatible = "fsl,ls2085a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		/*
+		 * We expect the enable-method for cpu's to be "psci", but this
+		 * is dependent on the SoC FW, which will fill this in.
+		 *
+		 * Currently supported enable-method is psci v0.2
+		 */
+
+		/* We have 4 clusters having 2 Cortex-A57 cores each */
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x0>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x1>;
+		};
+
+		cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x100>;
+		};
+
+		cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x101>;
+		};
+
+		cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x200>;
+		};
+
+		cpu@201 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x201>;
+		};
+
+		cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x300>;
+		};
+
+		cpu@301 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0 0x301>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x80000000>;
+		      /* DRAM space - 1, size : 2 GB DRAM */
+	};
+
+	gic: interrupt-controller@6000000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x06100000 0 0x100000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <1 9 0x4>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */
+			     <1 14 0x8>, /* Physical Non-Secure PPI, active-low */
+			     <1 11 0x8>, /* Virtual PPI, active-low */
+			     <1 10 0x8>; /* Hypervisor PPI, active-low */
+	};
+
+	serial0: serial@21c0500 {
+		device_type = "serial";
+		compatible = "fsl,ns16550", "ns16550a";
+		reg = <0x0 0x21c0500 0x0 0x100>;
+		clock-frequency = <0>;	/* Updated by bootloader */
+		interrupts = <0 32 0x1>; /* edge triggered */
+	};
+
+	serial1: serial@21c0600 {
+		device_type = "serial";
+		compatible = "fsl,ns16550", "ns16550a";
+		reg = <0x0 0x21c0600 0x0 0x100>;
+		clock-frequency = <0>; 	/* Updated by bootloader */
+		interrupts = <0 32 0x1>; /* edge triggered */
+	};
+
+	fsl_mc: fsl-mc@80c000000 {
+		compatible = "fsl,qoriq-mc";
+		reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
+		      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
+	};
+};

arch/arm64/boot/dts/mediatek/Makefile

+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
+
+always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
+clean-files	:= *.dtb

arch/arm64/boot/dts/mediatek/mt8173-evb.dts

+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ * Author: Eddie Huang <eddie.huang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+#include "mt8173.dtsi"
+
+/ {
+	model = "mediatek,mt8173-evb";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	chosen { };
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm64/boot/dts/mediatek/mt8173.dtsi

+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ * Author: Eddie Huang <eddie.huang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "mediatek,mt8173";
+	interrupt-parent = <&sysirq>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu2>;
+				};
+				core1 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x001>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x100>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x101>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend   = <0x84000001>;
+		cpu_off	      = <0x84000002>;
+		cpu_on	      = <0x84000003>;
+	};
+
+	uart_clk: dummy26m {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		#clock-cells = <0>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		sysirq: intpol-controller@10200620 {
+			compatible = "mediatek,mt8173-sysirq",
+					"mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10200620 0 0x20>;
+		};
+
+		gic: interrupt-controller@10220000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x10221000 0 0x1000>,
+			      <0 0x10222000 0 0x2000>,
+			      <0 0x10224000 0 0x2000>,
+			      <0 0x10226000 0 0x2000>;
+			interrupts = <GIC_PPI 9
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt8173-uart",
+					"mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x400>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt8173-uart",
+					"mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x400>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt8173-uart",
+					"mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart3: serial@11005000 {
+			compatible = "mediatek,mt8173-uart",
+					"mediatek,mt6577-uart";
+			reg = <0 0x11005000 0 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+	};
+
+};
+

arch/arm64/configs/defconfig

@@ -31,6 +31,8 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_FSL_LS2085A=y
+CONFIG_ARCH_MEDIATEK=y
 CONFIG_ARCH_THUNDER=y
 CONFIG_ARCH_VEXPRESS=y
 CONFIG_ARCH_XGENE=y
@@ -88,6 +90,7 @@ CONFIG_SERIO_AMBAKMI=y
 CONFIG_LEGACY_PTY_COUNT=16
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_MT6577=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y