Commit cd9af3da authored by Nate Case's avatar Nate Case Committed by Jeff Garzik

PHYLIB: Add 1000Base-X support for Broadcom bcm5482

Configure the BCM5482S secondary SerDes for 1000Base-X mode when the
appropriate dev_flags are passed in to phy_connect().  This is
needed when the PHY is used for fiber and backplane connections.
Signed-off-by: default avatarNate Case <ncase@xes-inc.com>
Signed-off-by: default avatarMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: default avatarJeff Garzik <jgarzik@redhat.com>
parent 3915c1e8
......@@ -24,6 +24,12 @@
#define MII_BCM54XX_ESR 0x11 /* BCM54xx extended status register */
#define MII_BCM54XX_ESR_IS 0x1000 /* Interrupt status */
#define MII_BCM54XX_EXP_DATA 0x15 /* Expansion register data */
#define MII_BCM54XX_EXP_SEL 0x17 /* Expansion register select */
#define MII_BCM54XX_EXP_SEL_SSD 0x0e00 /* Secondary SerDes select */
#define MII_BCM54XX_EXP_SEL_ER 0x0f00 /* Expansion register select */
#define MII_BCM54XX_AUX_CTL 0x18 /* Auxiliary control register */
#define MII_BCM54XX_ISR 0x1a /* BCM54xx interrupt status register */
#define MII_BCM54XX_IMR 0x1b /* BCM54xx interrupt mask register */
#define MII_BCM54XX_INT_CRCERR 0x0001 /* CRC error */
......@@ -42,10 +48,120 @@
#define MII_BCM54XX_INT_MDIX 0x2000 /* MDIX status change */
#define MII_BCM54XX_INT_PSERR 0x4000 /* Pair swap error */
#define MII_BCM54XX_SHD 0x1c /* 0x1c shadow registers */
#define MII_BCM54XX_SHD_WRITE 0x8000
#define MII_BCM54XX_SHD_VAL(x) ((x & 0x1f) << 10)
#define MII_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0)
/*
* Broadcom LED source encodings. These are used in BCM5461, BCM5481,
* BCM5482, and possibly some others.
*/
#define BCM_LED_SRC_LINKSPD1 0x0
#define BCM_LED_SRC_LINKSPD2 0x1
#define BCM_LED_SRC_XMITLED 0x2
#define BCM_LED_SRC_ACTIVITYLED 0x3
#define BCM_LED_SRC_FDXLED 0x4
#define BCM_LED_SRC_SLAVE 0x5
#define BCM_LED_SRC_INTR 0x6
#define BCM_LED_SRC_QUALITY 0x7
#define BCM_LED_SRC_RCVLED 0x8
#define BCM_LED_SRC_MULTICOLOR1 0xa
#define BCM_LED_SRC_OPENSHORT 0xb
#define BCM_LED_SRC_OFF 0xe /* Tied high */
#define BCM_LED_SRC_ON 0xf /* Tied low */
/*
* BCM5482: Shadow registers
* Shadow values go into bits [14:10] of register 0x1c to select a shadow
* register to access.
*/
#define BCM5482_SHD_LEDS1 0x0d /* 01101: LED Selector 1 */
/* LED3 / ~LINKSPD[2] selector */
#define BCM5482_SHD_LEDS1_LED3(src) ((src & 0xf) << 4)
/* LED1 / ~LINKSPD[1] selector */
#define BCM5482_SHD_LEDS1_LED1(src) ((src & 0xf) << 0)
#define BCM5482_SHD_SSD 0x14 /* 10100: Secondary SerDes control */
#define BCM5482_SHD_SSD_LEDM 0x0008 /* SSD LED Mode enable */
#define BCM5482_SHD_SSD_EN 0x0001 /* SSD enable */
#define BCM5482_SHD_MODE 0x1f /* 11111: Mode Control Register */
#define BCM5482_SHD_MODE_1000BX 0x0001 /* Enable 1000BASE-X registers */
/*
* BCM5482: Secondary SerDes registers
*/
#define BCM5482_SSD_1000BX_CTL 0x00 /* 1000BASE-X Control */
#define BCM5482_SSD_1000BX_CTL_PWRDOWN 0x0800 /* Power-down SSD */
#define BCM5482_SSD_SGMII_SLAVE 0x15 /* SGMII Slave Register */
#define BCM5482_SSD_SGMII_SLAVE_EN 0x0002 /* Slave mode enable */
#define BCM5482_SSD_SGMII_SLAVE_AD 0x0001 /* Slave auto-detection */
/*
* Device flags for PHYs that can be configured for different operating
* modes.
*/
#define PHY_BCM_FLAGS_VALID 0x80000000
#define PHY_BCM_FLAGS_INTF_XAUI 0x00000020
#define PHY_BCM_FLAGS_INTF_SGMII 0x00000010
#define PHY_BCM_FLAGS_MODE_1000BX 0x00000002
#define PHY_BCM_FLAGS_MODE_COPPER 0x00000001
MODULE_DESCRIPTION("Broadcom PHY driver");
MODULE_AUTHOR("Maciej W. Rozycki");
MODULE_LICENSE("GPL");
/*
* Indirect register access functions for the 1000BASE-T/100BASE-TX/10BASE-T
* 0x1c shadow registers.
*/
static int bcm54xx_shadow_read(struct phy_device *phydev, u16 shadow)
{
phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
}
static int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow, u16 val)
{
return phy_write(phydev, MII_BCM54XX_SHD,
MII_BCM54XX_SHD_WRITE |
MII_BCM54XX_SHD_VAL(shadow) |
MII_BCM54XX_SHD_DATA(val));
}
/*
* Indirect register access functions for the Expansion Registers
* and Secondary SerDes registers (when sec_serdes=1).
*/
static int bcm54xx_exp_read(struct phy_device *phydev,
int sec_serdes, u8 regnum)
{
int val;
phy_write(phydev, MII_BCM54XX_EXP_SEL,
(sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
MII_BCM54XX_EXP_SEL_ER) |
regnum);
val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
return val;
}
static int bcm54xx_exp_write(struct phy_device *phydev,
int sec_serdes, u8 regnum, u16 val)
{
int ret;
phy_write(phydev, MII_BCM54XX_EXP_SEL,
(sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
MII_BCM54XX_EXP_SEL_ER) |
regnum);
ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
return ret;
}
static int bcm54xx_config_init(struct phy_device *phydev)
{
int reg, err;
......@@ -70,6 +186,87 @@ static int bcm54xx_config_init(struct phy_device *phydev)
return 0;
}
static int bcm5482_config_init(struct phy_device *phydev)
{
int err, reg;
err = bcm54xx_config_init(phydev);
if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
/*
* Enable secondary SerDes and its use as an LED source
*/
reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_SSD);
bcm54xx_shadow_write(phydev, BCM5482_SHD_SSD,
reg |
BCM5482_SHD_SSD_LEDM |
BCM5482_SHD_SSD_EN);
/*
* Enable SGMII slave mode and auto-detection
*/
reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_SGMII_SLAVE);
bcm54xx_exp_write(phydev, 1, BCM5482_SSD_SGMII_SLAVE,
reg |
BCM5482_SSD_SGMII_SLAVE_EN |
BCM5482_SSD_SGMII_SLAVE_AD);
/*
* Disable secondary SerDes powerdown
*/
reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_1000BX_CTL);
bcm54xx_exp_write(phydev, 1, BCM5482_SSD_1000BX_CTL,
reg & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
/*
* Select 1000BASE-X register set (primary SerDes)
*/
reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_MODE);
bcm54xx_shadow_write(phydev, BCM5482_SHD_MODE,
reg | BCM5482_SHD_MODE_1000BX);
/*
* LED1=ACTIVITYLED, LED3=LINKSPD[2]
* (Use LED1 as secondary SerDes ACTIVITY LED)
*/
bcm54xx_shadow_write(phydev, BCM5482_SHD_LEDS1,
BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_ACTIVITYLED) |
BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_LINKSPD2));
/*
* Auto-negotiation doesn't seem to work quite right
* in this mode, so we disable it and force it to the
* right speed/duplex setting. Only 'link status'
* is important.
*/
phydev->autoneg = AUTONEG_DISABLE;
phydev->speed = SPEED_1000;
phydev->duplex = DUPLEX_FULL;
}
return err;
}
static int bcm5482_read_status(struct phy_device *phydev)
{
int err;
err = genphy_read_status(phydev);
if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
/*
* Only link status matters for 1000Base-X mode, so force
* 1000 Mbit/s full-duplex status
*/
if (phydev->link) {
phydev->speed = SPEED_1000;
phydev->duplex = DUPLEX_FULL;
}
}
return err;
}
static int bcm54xx_ack_interrupt(struct phy_device *phydev)
{
int reg;
......@@ -210,9 +407,9 @@ static struct phy_driver bcm5482_driver = {
.name = "Broadcom BCM5482",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = bcm54xx_config_init,
.config_init = bcm5482_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.read_status = bcm5482_read_status,
.ack_interrupt = bcm54xx_ack_interrupt,
.config_intr = bcm54xx_config_intr,
.driver = { .owner = THIS_MODULE },
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment