arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes

Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.

The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

arch/arm64/boot/dts/marvell/armada-7040-db.dts

@@ -124,6 +124,8 @@ &uart0 {
 
 &cp0_pcie2 {
 	status = "okay";
+	phys = <&cp0_comphy5 2>;
+	phy-names = "cp0-pcie2-x1-phy";
 };
 
 &cp0_i2c0 {

arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts

@@ -243,6 +243,8 @@ &cp0_pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cp0_pci0_reset_pins &cp0_wlan_disable_pins>;
 	reset-gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+	phys = <&cp0_comphy0 0>;
+	phy-names = "cp0-pcie0-x1-phy";
 	status = "okay";
 };
 

arch/arm64/boot/dts/marvell/armada-8040-db.dts

@@ -108,11 +108,15 @@ &uart0 {
 
 /* CON6 on CP0 expansion */
 &cp0_pcie0 {
+	phys = <&cp0_comphy0 0>;
+	phy-names = "cp0-pcie0-x1-phy";
 	status = "okay";
 };
 
 /* CON5 on CP0 expansion */
 &cp0_pcie2 {
+	phys = <&cp0_comphy5 2>;
+	phy-names = "cp0-pcie2-x1-phy";
 	status = "okay";
 };
 
@@ -198,16 +202,22 @@ &cp0_eth2 {
 
 /* CON6 on CP1 expansion */
 &cp1_pcie0 {
+	phys = <&cp1_comphy0 0>;
+	phy-names = "cp1-pcie0-x1-phy";
 	status = "okay";
 };
 
 /* CON7 on CP1 expansion */
 &cp1_pcie1 {
+	phys = <&cp1_comphy4 1>;
+	phy-names = "cp1-pcie1-x1-phy";
 	status = "okay";
 };
 
 /* CON5 on CP1 expansion */
 &cp1_pcie2 {
+	phys = <&cp1_comphy5 2>;
+	phy-names = "cp1-pcie2-x1-phy";
 	status = "okay";
 };
 

arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi

@@ -186,6 +186,10 @@ &cp0_pcie0 {
 	reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
 	ranges = <0x81000000 0x0 0xf9010000 0x0 0xf9010000 0x0 0x10000
 		  0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
+	phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>,
+	       <&cp0_comphy2 0>, <&cp0_comphy3 0>;
+	phy-names = "cp0-pcie0-x4-lane0-phy", "cp0-pcie0-x4-lane1-phy",
+		    "cp0-pcie0-x4-lane2-phy", "cp0-pcie0-x4-lane3-phy";
 	status = "okay";
 };