entry-armv.S, debug.S, bios32.c:

  IXP4xx support

arch/arm/kernel/bios32.c

@@ -155,6 +155,30 @@ static void __devinit pci_fixup_dec21285(struct pci_dev *dev)
 	}
 }
 
+/*
+ * Same as above. The PrPMC800 carrier board for the PrPMC1100 
+ * card maps the host-bridge @ 00:01:00 for some reason and it
+ * ends up getting scanned. Note that we only want to do this
+ * fixup when we find the IXP4xx on a PrPMC system, which is why
+ * we check the machine type. We could be running on a board
+ * with an IXP4xx target device and we don't want to kill the
+ * resources in that case.
+ */
+static void __devinit pci_fixup_prpmc1100(struct pci_dev *dev)
+{
+	int i;
+
+	if (machine_is_prpmc1100()) {
+		dev->class &= 0xff;
+		dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
+		for (i = 0; i < PCI_NUM_RESOURCES; i++) {
+			dev->resource[i].start = 0;
+			dev->resource[i].end   = 0;
+			dev->resource[i].flags = 0;
+		}
+	}
+}
+
 /*
  * PCI IDE controllers use non-standard I/O port decoding, respect it.
  */
@@ -273,6 +297,10 @@ struct pci_fixup pcibios_fixups[] = {
 		PCI_FIXUP_HEADER,
 		PCI_ANY_ID,		PCI_ANY_ID,
 		pci_fixup_ide_bases
+	}, {
+		PCI_FIXUP_HEADER,
+		PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_IXP4XX,
+		pci_fixup_prpmc1100
 	}, { 0 }
 };
 

arch/arm/kernel/debug.S

@@ -465,6 +465,31 @@
 		beq	1001b
 		.endm
 
+#elif defined(CONFIG_ARCH_IXP4XX)
+
+                .macro  addruart,rx
+                mrc     p15, 0, \rx, c1, c0
+                tst     \rx, #1                 @ MMU enabled?
+                moveq   \rx, #0xc8000000
+                movne   \rx, #0xff000000
+                add     \rx,\rx,#3              @ Uart regs are at off set of 3 if
+						@ byte writes used - Big Endian.
+                .endm
+
+               .macro  senduart,rd,rx
+                strb    \rd, [\rx]
+                .endm
+
+                .macro  waituart,rd,rx
+1002:           ldrb    \rd, [\rx, #0x14]
+                and     \rd, \rd, #0x60		@ check THRE and TEMT bits
+                teq     \rd, #0x60
+                bne     1002b
+                .endm
+
+                .macro  busyuart,rd,rx
+                .endm
+
 #elif defined(CONFIG_ARCH_OMAP)
 
 #include <asm/arch/serial.h>

arch/arm/kernel/entry-armv.S

@@ -639,6 +639,34 @@ ENTRY(soft_irq_mask)
 		.macro	irq_prio_table
 		.endm
 
+#elif defined (CONFIG_ARCH_IXP4XX)
+
+		.macro	disable_fiq
+		.endm
+		
+		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+		ldr	\irqstat, =(IXP4XX_INTC_BASE_VIRT+IXP4XX_ICIP_OFFSET)
+		ldr	\irqstat, [\irqstat]		@ get interrupts
+		cmp	\irqstat, #0
+		beq	1002f
+		clz     \irqnr, \irqstat
+		mov     \base, #31
+		subs    \irqnr, \base, \irqnr
+		
+/*
+1001:		tst	\irqstat, #1
+		addeq	\irqnr, \irqnr, #1
+		moveq	\irqstat, \irqstat, lsr #1
+		tsteq	\irqnr, #32
+		beq	1001b
+		teq	\irqnr, #32
+*/
+1002:
+		.endm
+
+                .macro  irq_prio_table
+                .endm
+
 #elif defined(CONFIG_ARCH_OMAP)
 
 		.macro	disable_fiq