Commit d8bd64c1 authored by Jon Mason's avatar Jon Mason Committed by Florian Fainelli

ARM64: dts: enable clock support for Broadcom NS2

Add device tree entries for clock support for Broadcom Northstar 2 SoC
Signed-off-by: default avatarJon Mason <jonmason@broadcom.com>
Reviewed-by: default avatarRay Jui <rjui@broadcom.com>
Signed-off-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
parent c6fe9a2e
......@@ -31,6 +31,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/bcm-ns2.h>
/memreserve/ 0x84b00000 0x00000008;
......@@ -109,6 +110,33 @@ pmu {
<&A57_3>;
};
clocks {
#address-cells = <1>;
#size-cells = <1>;
osc: oscillator {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
};
iprocmed: iprocmed {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
clock-div = <2>;
clock-mult = <1>;
};
iprocslow: iprocslow {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clocks = <&genpll_scr BCM_NS2_GENPLL_SCR_SCR_CLK>;
clock-div = <4>;
clock-mult = <1>;
};
};
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
......@@ -156,6 +184,56 @@ smmu: mmu@64000000 {
mmu-masters;
};
lcpll_ddr: lcpll_ddr@6501d058 {
#clock-cells = <1>;
compatible = "brcm,ns2-lcpll-ddr";
reg = <0x6501d058 0x20>,
<0x6501c020 0x4>,
<0x6501d04c 0x4>;
clocks = <&osc>;
clock-output-names = "lcpll_ddr", "pcie_sata_usb",
"ddr", "ddr_ch2_unused",
"ddr_ch3_unused", "ddr_ch4_unused",
"ddr_ch5_unused";
};
lcpll_ports: lcpll_ports@6501d078 {
#clock-cells = <1>;
compatible = "brcm,ns2-lcpll-ports";
reg = <0x6501d078 0x20>,
<0x6501c020 0x4>,
<0x6501d054 0x4>;
clocks = <&osc>;
clock-output-names = "lcpll_ports", "wan", "rgmii",
"ports_ch2_unused",
"ports_ch3_unused",
"ports_ch4_unused",
"ports_ch5_unused";
};
genpll_scr: genpll_scr@6501d098 {
#clock-cells = <1>;
compatible = "brcm,ns2-genpll-scr";
reg = <0x6501d098 0x32>,
<0x6501c020 0x4>,
<0x6501d044 0x4>;
clocks = <&osc>;
clock-output-names = "genpll_scr", "scr", "fs",
"audio_ref", "scr_ch3_unused",
"scr_ch4_unused", "scr_ch5_unused";
};
genpll_sw: genpll_sw@6501d0c4 {
#clock-cells = <1>;
compatible = "brcm,ns2-genpll-sw";
reg = <0x6501d0c4 0x32>,
<0x6501c020 0x4>,
<0x6501d044 0x4>;
clocks = <&osc>;
clock-output-names = "genpll_sw", "rpe", "250", "nic",
"chimp", "port", "sdio";
};
crmu: crmu@65024000 {
compatible = "syscon";
reg = <0x65024000 0x100>;
......@@ -204,7 +282,7 @@ uart3: serial@66130000 {
interrupts = <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <23961600>;
clocks = <&osc>;
status = "disabled";
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment