MIPS: lantiq: Remove the arch/mips/lantiq/xway/reset.c implementation

The RCU register are now access through separates drivers. remove the
last pieces of the old implementation.

The GPHY reset bits are now set by the GPHY driver which registers a
reboot notifier. The reboot is triggered by a syscon-reboot driver and
the MIPS specific parts are done by the generic MIPS implementation in
arch/mips/kernel/reset.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: john@phrozen.org
Cc: robh@kernel.org
Cc: andy.shevchenko@gmail.com
Cc: p.zabel@pengutronix.de
Cc: kishon@ti.com
Cc: mark.rutland@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17131/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/lantiq/Kconfig

@@ -18,6 +18,7 @@ config SOC_XWAY
 	select SOC_TYPE_XWAY
 	select HW_HAS_PCI
 	select MFD_SYSCON
+	select MFD_CORE
 
 config SOC_FALCON
 	bool "FALCON"

arch/mips/lantiq/xway/Makefile

-obj-y := prom.o sysctrl.o clk.o reset.o dma.o gptu.o dcdc.o
+obj-y := prom.o sysctrl.o clk.o dma.o gptu.o dcdc.o
 
 obj-y += vmmc.o

arch/mips/lantiq/xway/reset.c

-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <john@phrozen.org>
- *  Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
- */
-
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/ioport.h>
-#include <linux/pm.h>
-#include <linux/export.h>
-#include <linux/delay.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-#include <linux/reset-controller.h>
-
-#include <asm/reboot.h>
-
-#include <lantiq_soc.h>
-
-#include "../prom.h"
-
-/* reset request register */
-#define RCU_RST_REQ		0x0010
-/* reset status register */
-#define RCU_RST_STAT		0x0014
-
-/* xbar BE flag */
-#define RCU_AHB_ENDIAN          0x004C
-#define RCU_VR9_BE_AHB1S        0x00000008
-
-/* reboot bit */
-#define RCU_RD_GPHY0_XRX200	BIT(31)
-#define RCU_RD_SRST		BIT(30)
-#define RCU_RD_GPHY1_XRX200	BIT(29)
-
-/* reset cause */
-#define RCU_STAT_SHIFT		26
-/* boot selection */
-#define RCU_BOOT_SEL(x)		((x >> 18) & 0x7)
-#define RCU_BOOT_SEL_XRX200(x)	(((x >> 17) & 0xf) | ((x >> 8) & 0x10))
-
-/* dwc2 USB configuration registers */
-#define RCU_USB1CFG		0x0018
-#define RCU_USB2CFG		0x0034
-
-/* USB DMA endianness bits */
-#define RCU_USBCFG_HDSEL_BIT	BIT(11)
-#define RCU_USBCFG_HOST_END_BIT	BIT(10)
-#define RCU_USBCFG_SLV_END_BIT	BIT(9)
-
-/* USB reset bits */
-#define RCU_USBRESET		0x0010
-
-#define USBRESET_BIT		BIT(4)
-
-#define RCU_USBRESET2		0x0048
-
-#define USB1RESET_BIT		BIT(4)
-#define USB2RESET_BIT		BIT(5)
-
-#define RCU_CFG1A		0x0038
-#define RCU_CFG1B		0x003C
-
-/* USB PMU devices */
-#define PMU_AHBM		BIT(15)
-#define PMU_USB0		BIT(6)
-#define PMU_USB1		BIT(27)
-
-/* USB PHY PMU devices */
-#define PMU_USB0_P		BIT(0)
-#define PMU_USB1_P		BIT(26)
-
-/* remapped base addr of the reset control unit */
-static void __iomem *ltq_rcu_membase;
-static struct device_node *ltq_rcu_np;
-
-static void ltq_rcu_w32(uint32_t val, uint32_t reg_off)
-{
-	ltq_w32(val, ltq_rcu_membase + reg_off);
-}
-
-static uint32_t ltq_rcu_r32(uint32_t reg_off)
-{
-	return ltq_r32(ltq_rcu_membase + reg_off);
-}
-
-static void ltq_machine_restart(char *command)
-{
-	u32 val = ltq_rcu_r32(RCU_RST_REQ);
-
-	if (of_device_is_compatible(ltq_rcu_np, "lantiq,rcu-xrx200"))
-		val |= RCU_RD_GPHY1_XRX200 | RCU_RD_GPHY0_XRX200;
-
-	val |= RCU_RD_SRST;
-
-	local_irq_disable();
-	ltq_rcu_w32(val, RCU_RST_REQ);
-	unreachable();
-}
-
-static void ltq_machine_halt(void)
-{
-	local_irq_disable();
-	unreachable();
-}
-
-static void ltq_machine_power_off(void)
-{
-	local_irq_disable();
-	unreachable();
-}
-
-static int __init mips_reboot_setup(void)
-{
-	struct resource res;
-
-	ltq_rcu_np = of_find_compatible_node(NULL, NULL, "lantiq,rcu-xway");
-	if (!ltq_rcu_np)
-		ltq_rcu_np = of_find_compatible_node(NULL, NULL,
-							"lantiq,rcu-xrx200");
-
-	/* check if all the reset register range is available */
-	if (!ltq_rcu_np)
-		panic("Failed to load reset resources from devicetree");
-
-	if (of_address_to_resource(ltq_rcu_np, 0, &res))
-		panic("Failed to get rcu memory range");
-
-	if (!request_mem_region(res.start, resource_size(&res), res.name))
-		pr_err("Failed to request rcu memory");
-
-	ltq_rcu_membase = ioremap_nocache(res.start, resource_size(&res));
-	if (!ltq_rcu_membase)
-		panic("Failed to remap core memory");
-
-	_machine_restart = ltq_machine_restart;
-	_machine_halt = ltq_machine_halt;
-	pm_power_off = ltq_machine_power_off;
-
-	return 0;
-}
-
-arch_initcall(mips_reboot_setup);