Commit e3502b82 authored by Vladimir Oltean's avatar Vladimir Oltean Committed by David S. Miller

net: dsa: sja1105: Make vid 1 the default pvid

In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.

The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:

  8021q: adding VLAN 0 to HW filter on device swp2

So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: default avatarVladimir Oltean <olteanv@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 29dd908d
...@@ -80,7 +80,7 @@ static int sja1105_init_mac_settings(struct sja1105_private *priv) ...@@ -80,7 +80,7 @@ static int sja1105_init_mac_settings(struct sja1105_private *priv)
.maxage = 0xFF, .maxage = 0xFF,
/* Internal VLAN (pvid) to apply to untagged ingress */ /* Internal VLAN (pvid) to apply to untagged ingress */
.vlanprio = 0, .vlanprio = 0,
.vlanid = 0, .vlanid = 1,
.ing_mirr = false, .ing_mirr = false,
.egr_mirr = false, .egr_mirr = false,
/* Don't drop traffic with other EtherType than ETH_P_IP */ /* Don't drop traffic with other EtherType than ETH_P_IP */
...@@ -264,20 +264,15 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv) ...@@ -264,20 +264,15 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv)
.vmemb_port = 0, .vmemb_port = 0,
.vlan_bc = 0, .vlan_bc = 0,
.tag_port = 0, .tag_port = 0,
.vlanid = 0, .vlanid = 1,
}; };
int i; int i;
table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP]; table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];
/* The static VLAN table will only contain the initial pvid of 0. /* The static VLAN table will only contain the initial pvid of 1.
* All other VLANs are to be configured through dynamic entries, * All other VLANs are to be configured through dynamic entries,
* and kept in the static configuration table as backing memory. * and kept in the static configuration table as backing memory.
* The pvid of 0 is sufficient to pass traffic while the ports are
* standalone and when vlan_filtering is disabled. When filtering
* gets enabled, the switchdev core sets up the VLAN ID 1 and sets
* it as the new pvid. Actually 'pvid 1' still comes up in 'bridge
* vlan' even when vlan_filtering is off, but it has no effect.
*/ */
if (table->entry_count) { if (table->entry_count) {
kfree(table->entries); kfree(table->entries);
...@@ -291,7 +286,7 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv) ...@@ -291,7 +286,7 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv)
table->entry_count = 1; table->entry_count = 1;
/* VLAN ID 0: all DT-defined ports are members; no restrictions on /* VLAN 1: all DT-defined ports are members; no restrictions on
* forwarding; always transmit priority-tagged frames as untagged. * forwarding; always transmit priority-tagged frames as untagged.
*/ */
for (i = 0; i < SJA1105_NUM_PORTS; i++) { for (i = 0; i < SJA1105_NUM_PORTS; i++) {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment