hwmon: (abituguru) Depend on DMI

The abituguru drivers are only built on X86, where DMI support is now
enabled by default. So let these drivers depend on DMI, for the
following gains:
* Robustness and safety. Detection of these devices is weak and uses
  non-standard methods, it should really be limited to Abit boards
  unless the user explicitly asks otherwise.
* Code simplicity. The code is easier to read without ifdefs.
* Better build testing coverage. Now there's only one way to build the
  drivers, so no risk of build failure on exotic systems.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>

drivers/hwmon/Kconfig

@@ -41,7 +41,7 @@ comment "Native drivers"
 
 config SENSORS_ABITUGURU
 	tristate "Abit uGuru (rev 1 & 2)"
-	depends on X86 && EXPERIMENTAL
+	depends on X86 && DMI && EXPERIMENTAL
 	help
 	  If you say yes here you get support for the sensor part of the first
 	  and second revision of the Abit uGuru chip. The voltage and frequency
@@ -56,7 +56,7 @@ config SENSORS_ABITUGURU
 
 config SENSORS_ABITUGURU3
 	tristate "Abit uGuru (rev 3)"
-	depends on X86 && EXPERIMENTAL
+	depends on X86 && DMI && EXPERIMENTAL
 	help
 	  If you say yes here you get support for the sensor part of the
 	  third revision of the Abit uGuru chip. Only reading the sensors

drivers/hwmon/abituguru.c

@@ -1448,15 +1448,12 @@ static int __init abituguru_init(void)
 {
 	int address, err;
 	struct resource res = { .flags = IORESOURCE_IO };
-
-#ifdef CONFIG_DMI
 	const char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
 
 	/* safety check, refuse to load on non Abit motherboards */
 	if (!force && (!board_vendor ||
 			strcmp(board_vendor, "http://www.abit.com.tw/")))
 		return -ENODEV;
-#endif
 
 	address = abituguru_detect();
 	if (address < 0)

drivers/hwmon/abituguru3.c

@@ -1119,8 +1119,6 @@ static struct platform_driver abituguru3_driver = {
 	.resume = abituguru3_resume
 };
 
-#ifdef CONFIG_DMI
-
 static int __init abituguru3_dmi_detect(void)
 {
 	const char *board_vendor, *board_name;
@@ -1159,15 +1157,6 @@ static int __init abituguru3_dmi_detect(void)
 	return 1;
 }
 
-#else /* !CONFIG_DMI */
-
-static inline int abituguru3_dmi_detect(void)
-{
-	return 1;
-}
-
-#endif /* CONFIG_DMI */
-
 /* FIXME: Manual detection should die eventually; we need to collect stable
  *        DMI model names first before we can rely entirely on CONFIG_DMI.
  */
@@ -1216,10 +1205,8 @@ static int __init abituguru3_init(void)
 		if (err)
 			return err;
 
-#ifdef CONFIG_DMI
 		pr_warn("this motherboard was not detected using DMI. "
 			"Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n");
-#endif
 	}
 
 	err = platform_driver_register(&abituguru3_driver);