phy: mvebu-cp110-comphy: Add SATA support

Add the corresponding entries in the COMPHY modes table.

SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

drivers/phy/marvell/phy-mvebu-cp110-comphy.c

@@ -155,6 +155,7 @@
 #define COMPHY_FW_PARAM_ETH(mode, port, speed)				\
 	COMPHY_FW_PARAM_FULL(mode, port, speed, 0)
 
+#define COMPHY_FW_MODE_SATA		0x1
 #define COMPHY_FW_MODE_SGMII		0x2 /* SGMII 1G */
 #define COMPHY_FW_MODE_HS_SGMII		0x3 /* SGMII 2.5G */
 #define COMPHY_FW_MODE_USB3H		0x4
@@ -195,9 +196,11 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	/* lane 0 */
 	ETH_CONF(0, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(0, 1, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
+	GEN_CONF(0, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	/* lane 1 */
 	GEN_CONF(1, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
 	GEN_CONF(1, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D),
+	GEN_CONF(1, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	ETH_CONF(1, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(1, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
 	/* lane 2 */
@@ -206,11 +209,13 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI),
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1, COMPHY_FW_MODE_XFI),
 	GEN_CONF(2, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
+	GEN_CONF(2, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	/* lane 3 */
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII),
 	ETH_CONF(3, 1, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI),
 	GEN_CONF(3, 1, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
+	GEN_CONF(3, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	/* lane 4 */
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII),
@@ -223,6 +228,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GKR, -1, COMPHY_FW_MODE_XFI),
 	/* lane 5 */
 	ETH_CONF(5, 1, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI),
+	GEN_CONF(5, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	ETH_CONF(5, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(5, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
 };
@@ -666,6 +672,10 @@ static int mvebu_comphy_power_on(struct phy *phy)
 		dev_dbg(priv->dev, "set lane %d to USB3 mode\n", lane->id);
 		fw_param = COMPHY_FW_PARAM(fw_mode, lane->port);
 		break;
+	case PHY_MODE_SATA:
+		dev_dbg(priv->dev, "set lane %d to SATA mode\n", lane->id);
+		fw_param = COMPHY_FW_PARAM(fw_mode, lane->port);
+		break;
 	default:
 		dev_err(priv->dev, "unsupported PHY mode (%d)\n", lane->mode);
 		return -ENOTSUPP;