icside: fix ->speedproc to return on unsupported modes (take 5)

* All other implementations of ->speedproc return zero on success
  and non-zero on failure.  Currently it doesn't matter for icside host
  driver and isn't a bug per se since:

  - ide_set_xfer_rate() return value is ignored by all IDE core users

  - icside doesn't (yet!) use ide_tune_dma() in icside_dma_check()

  but sooner or later we will need to fix anyway - so lets do it now.

* icside_set_speed() happily accepts unsupported transfer modes which
  results in drive->drive_data being set to the maximum value (480)
  and drive->current_speed being set to the unsupported transfer mode.

  Fix it.

v2:
* The initial version of the patch was broken because it didn't take into
  the account (the different from usual) return values of icside_set_speed()
  (Noticed by Russell).

v3:
* Remove no longer needed initialization/checking of cycle_time
  (Noticed by Sergei).

* No need to set drive->drive_data if DMA is not going to be used
  (Noticed by Sergei).

* Remove incorrect setting of drive->current_speed
  (Noticed by Sergei).

* Move ide_config_drive_speed() at the end of icside_set_speed().

v4:
* If DMA mode is not found in icside_dma_check() then just return "-1" and
  don't call icside_set_speed() (v3 got it wrong and "1" was returned instead).

v5:
* Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return
  value (just like it was before this patch).

Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent ca1997c1
......@@ -250,7 +250,7 @@ static void icside_build_sglist(ide_drive_t *drive, struct request *rq)
*/
static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
{
int on = 0, cycle_time = 0, use_dma_info = 0;
int cycle_time, use_dma_info = 0;
switch (xfer_mode) {
case XFER_MW_DMA_2:
......@@ -272,6 +272,8 @@ static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
case XFER_SW_DMA_0:
cycle_time = 480;
break;
default:
return 1;
}
/*
......@@ -283,17 +285,10 @@ static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
drive->drive_data = cycle_time;
if (cycle_time && ide_config_drive_speed(drive, xfer_mode) == 0)
on = 1;
else
drive->drive_data = 480;
printk("%s: %s selected (peak %dMB/s)\n", drive->name,
ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
drive->current_speed = xfer_mode;
return on;
return ide_config_drive_speed(drive, xfer_mode);
}
static void icside_dma_host_off(ide_drive_t *drive)
......@@ -320,8 +315,7 @@ static int icside_dma_check(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
int xfer_mode = XFER_PIO_2;
int on;
int xfer_mode = 0;
if (!(id->capability & 1) || !hwif->autodma)
goto out;
......@@ -350,9 +344,10 @@ static int icside_dma_check(ide_drive_t *drive)
}
out:
on = icside_set_speed(drive, xfer_mode);
if (xfer_mode == 0)
return -1;
return on ? 0 : -1;
return icside_set_speed(drive, xfer_mode) ? -1 : 0;
}
static int icside_dma_end(ide_drive_t *drive)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment