Commit f4c41b26 authored by Haavard Skinnemoen's avatar Haavard Skinnemoen

[AVR32] ATSTK1000: Move gpio-leds setup to setup.c

There may be other boards than STK1002 that want to use the leds on
STK1000. Move it to stk1000 common code to make it easier to reuse.
Signed-off-by: default avatarHaavard Skinnemoen <hskinnemoen@atmel.com>
parent 438ff3f3
......@@ -50,9 +50,9 @@ config BOARD_ATSTK1002_SPI1
GPIO lines and accessed through the J1 jumper block. Say "y"
here to configure that SPI controller.
config BOARD_ATSTK1002_J2_LED
config BOARD_ATSTK1000_J2_LED
bool
default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB
default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
choice
prompt "LEDs connected to J2:"
......@@ -64,12 +64,12 @@ choice
IDC cable. A default "heartbeat" trigger is provided, but
you can of course override this.
config BOARD_ATSTK1002_J2_LED8
config BOARD_ATSTK1000_J2_LED8
bool "LED0..LED7"
help
Select this if J2 is jumpered to LED0..LED7 amber leds.
config BOARD_ATSTK1002_J2_RGB
config BOARD_ATSTK1000_J2_RGB
bool "RGB leds"
help
Select this if J2 is jumpered to the RGB leds.
......
......@@ -12,4 +12,6 @@
extern struct atmel_lcdfb_info atstk1000_lcdc_data;
void atstk1000_setup_j2_leds(void);
#endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */
......@@ -11,7 +11,6 @@
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/string.h>
#include <linux/types.h>
......@@ -22,7 +21,7 @@
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/arch/at32ap7000.h>
#include <asm/arch/at32ap700x.h>
#include <asm/arch/board.h>
#include <asm/arch/init.h>
#include <asm/arch/portmux.h>
......@@ -141,65 +140,6 @@ static void __init set_hw_addr(struct platform_device *pdev)
clk_put(pclk);
}
#ifdef CONFIG_BOARD_ATSTK1002_J2_LED
static struct gpio_led stk_j2_led[] = {
#ifdef CONFIG_BOARD_ATSTK1002_J2_LED8
#define LEDSTRING "J2 jumpered to LED8"
{ .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
{ .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
{ .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
{ .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
{ .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
{ .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
{ .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
{ .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
.default_trigger = "heartbeat", },
#else /* RGB */
#define LEDSTRING "J2 jumpered to RGB LEDs"
{ .name = "r1:red", .gpio = GPIO_PIN_PB( 8), },
{ .name = "g1:green", .gpio = GPIO_PIN_PB(10), },
{ .name = "b1:blue", .gpio = GPIO_PIN_PB(14), },
{ .name = "r2:red", .gpio = GPIO_PIN_PB( 9),
.default_trigger = "heartbeat", },
{ .name = "g2:green", .gpio = GPIO_PIN_PB(13), },
{ .name = "b2:blue", .gpio = GPIO_PIN_PB(15),
.default_trigger = "heartbeat", },
/* PB16, PB30 unused */
#endif
};
static struct gpio_led_platform_data stk_j2_led_data = {
.num_leds = ARRAY_SIZE(stk_j2_led),
.leds = stk_j2_led,
};
static struct platform_device stk_j2_led_dev = {
.name = "leds-gpio",
.id = 2, /* gpio block J2 */
.dev = {
.platform_data = &stk_j2_led_data,
},
};
static void setup_j2_leds(void)
{
unsigned i;
for (i = 0; i < ARRAY_SIZE(stk_j2_led); i++)
at32_select_gpio(stk_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
printk("STK1002: " LEDSTRING "\n");
platform_device_register(&stk_j2_led_dev);
}
#else
static void setup_j2_leds(void)
{
}
#endif
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
static void __init at73c213_set_clk(struct at73c213_board_info *info)
......@@ -298,7 +238,7 @@ static int __init atstk1002_init(void)
at32_add_device_ssc(0, ATMEL_SSC_TX);
#endif
setup_j2_leds();
atstk1000_setup_j2_leds();
#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
......
......@@ -10,13 +10,17 @@
#include <linux/bootmem.h>
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/linkage.h>
#include <video/atmel_lcdc.h>
#include <asm/setup.h>
#include <asm/arch/at32ap700x.h>
#include <asm/arch/board.h>
#include <asm/arch/portmux.h>
#include "atstk1000.h"
......@@ -61,3 +65,63 @@ struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
.default_monspecs = &atstk1000_default_monspecs,
.guard_time = 2,
};
#ifdef CONFIG_BOARD_ATSTK1000_J2_LED
#include <linux/leds.h>
static struct gpio_led stk1000_j2_led[] = {
#ifdef CONFIG_BOARD_ATSTK1000_J2_LED8
#define LEDSTRING "J2 jumpered to LED8"
{ .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
{ .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
{ .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
{ .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
{ .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
{ .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
{ .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
{ .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
.default_trigger = "heartbeat", },
#else /* RGB */
#define LEDSTRING "J2 jumpered to RGB LEDs"
{ .name = "r1:red", .gpio = GPIO_PIN_PB( 8), },
{ .name = "g1:green", .gpio = GPIO_PIN_PB(10), },
{ .name = "b1:blue", .gpio = GPIO_PIN_PB(14), },
{ .name = "r2:red", .gpio = GPIO_PIN_PB( 9),
.default_trigger = "heartbeat", },
{ .name = "g2:green", .gpio = GPIO_PIN_PB(13), },
{ .name = "b2:blue", .gpio = GPIO_PIN_PB(15),
.default_trigger = "heartbeat", },
/* PB16, PB30 unused */
#endif
};
static struct gpio_led_platform_data stk1000_j2_led_data = {
.num_leds = ARRAY_SIZE(stk1000_j2_led),
.leds = stk1000_j2_led,
};
static struct platform_device stk1000_j2_led_dev = {
.name = "leds-gpio",
.id = 2, /* gpio block J2 */
.dev = {
.platform_data = &stk1000_j2_led_data,
},
};
void __init atstk1000_setup_j2_leds(void)
{
unsigned i;
for (i = 0; i < ARRAY_SIZE(stk1000_j2_led); i++)
at32_select_gpio(stk1000_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
printk("STK1000: " LEDSTRING "\n");
platform_device_register(&stk1000_j2_led_dev);
}
#else /* CONFIG_BOARD_ATSTK1000_J2_LED */
void __init atstk1000_setup_j2_leds(void)
{
}
#endif /* CONFIG_BOARD_ATSTK1000_J2_LED */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment