usb: mtu3: reinitialize CSR registers

The CSR registers will be reset as default value if the
ports are disabled, so reinitialize them when the ports
are enabled again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1595834101-13094-3-git-send-email-chunfeng.yun@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/mtu3/mtu3_core.c

@@ -202,6 +202,36 @@ static void mtu3_intr_enable(struct mtu3 *mtu)
 	mtu3_writel(mbase, U3D_DEV_LINK_INTR_ENABLE, SSUSB_DEV_SPEED_CHG_INTR);
 }
 
+static void mtu3_set_speed(struct mtu3 *mtu);
+
+/* CSR registers will be reset to default value if port is disabled */
+static void mtu3_csr_init(struct mtu3 *mtu)
+{
+	void __iomem *mbase = mtu->mac_base;
+
+	if (mtu->is_u3_ip) {
+		/* disable LGO_U1/U2 by default */
+		mtu3_clrbits(mbase, U3D_LINK_POWER_CONTROL,
+				SW_U1_REQUEST_ENABLE | SW_U2_REQUEST_ENABLE);
+		/* enable accept LGO_U1/U2 link command from host */
+		mtu3_setbits(mbase, U3D_LINK_POWER_CONTROL,
+				SW_U1_ACCEPT_ENABLE | SW_U2_ACCEPT_ENABLE);
+		/* device responses to u3_exit from host automatically */
+		mtu3_clrbits(mbase, U3D_LTSSM_CTRL, SOFT_U3_EXIT_EN);
+		/* automatically build U2 link when U3 detect fail */
+		mtu3_setbits(mbase, U3D_USB2_TEST_MODE, U2U3_AUTO_SWITCH);
+		/* auto clear SOFT_CONN when clear USB3_EN if work as HS */
+		mtu3_setbits(mbase, U3D_U3U2_SWITCH_CTRL, SOFTCON_CLR_AUTO_EN);
+	}
+
+	mtu3_set_speed(mtu);
+
+	/* delay about 0.1us from detecting reset to send chirp-K */
+	mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
+	/* enable automatical HWRW from L1 */
+	mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, LPM_HRWE);
+}
+
 /* reset: u2 - data toggle, u3 - SeqN, flow control status etc */
 static void mtu3_ep_reset(struct mtu3_ep *mep)
 {
@@ -267,13 +297,7 @@ void mtu3_start(struct mtu3 *mtu)
 
 	mtu3_clrbits(mtu->ippc_base, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
 
-	/*
-	 * When disable U2 port, USB2_CSR's register will be reset to
-	 * default value after re-enable it again(HS is enabled by default).
-	 * So if force mac to work as FS, disable HS function.
-	 */
-	if (mtu->max_speed == USB_SPEED_FULL)
-		mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+	mtu3_csr_init(mtu);
 
 	/* Initialize the default interrupts */
 	mtu3_intr_enable(mtu);
@@ -572,39 +596,18 @@ static void mtu3_set_speed(struct mtu3 *mtu)
 
 static void mtu3_regs_init(struct mtu3 *mtu)
 {
-
 	void __iomem *mbase = mtu->mac_base;
 
 	/* be sure interrupts are disabled before registration of ISR */
 	mtu3_intr_disable(mtu);
 	mtu3_intr_status_clear(mtu);
 
-	if (mtu->is_u3_ip) {
-		/* disable LGO_U1/U2 by default */
-		mtu3_clrbits(mbase, U3D_LINK_POWER_CONTROL,
-				SW_U1_REQUEST_ENABLE | SW_U2_REQUEST_ENABLE);
-		/* enable accept LGO_U1/U2 link command from host */
-		mtu3_setbits(mbase, U3D_LINK_POWER_CONTROL,
-				SW_U1_ACCEPT_ENABLE | SW_U2_ACCEPT_ENABLE);
-		/* device responses to u3_exit from host automatically */
-		mtu3_clrbits(mbase, U3D_LTSSM_CTRL, SOFT_U3_EXIT_EN);
-		/* automatically build U2 link when U3 detect fail */
-		mtu3_setbits(mbase, U3D_USB2_TEST_MODE, U2U3_AUTO_SWITCH);
-		/* auto clear SOFT_CONN when clear USB3_EN if work as HS */
-		mtu3_setbits(mbase, U3D_U3U2_SWITCH_CTRL, SOFTCON_CLR_AUTO_EN);
-	}
-
-	mtu3_set_speed(mtu);
+	mtu3_csr_init(mtu);
 
-	/* delay about 0.1us from detecting reset to send chirp-K */
-	mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
 	/* U2/U3 detected by HW */
 	mtu3_writel(mbase, U3D_DEVICE_CONF, 0);
 	/* vbus detected by HW */
 	mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
-	/* enable automatical HWRW from L1 */
-	mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, LPM_HRWE);
-
 	/* use new QMU format when HW version >= 0x1003 */
 	if (mtu->gen2cp)
 		mtu3_writel(mbase, U3D_QFCR, ~0x0);