Commit f692f776 authored by Bartlomiej Zolnierkiewicz's avatar Bartlomiej Zolnierkiewicz Committed by Greg Kroah-Hartman

tty: remove redundant 'default n' from Kconfig-s

'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.

Also since commit f467c564 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:

    ...
    One side effect of (and the main motivation for) this change is making
    the following two definitions behave exactly the same:

        config FOO
                bool

        config FOO
                bool
                default n

    With this change, neither of these will generate a
    '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
    That might make it clearer to people that a bare 'default n' is
    redundant.
    ...
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 7a7457ba
......@@ -84,7 +84,6 @@ config HW_CONSOLE
config VT_HW_CONSOLE_BINDING
bool "Support for binding and unbinding console drivers"
depends on HW_CONSOLE
default n
---help---
The virtual terminal is the device that interacts with the physical
terminal through console drivers. On these systems, at least one
......@@ -313,7 +312,6 @@ config N_GSM
config TRACE_ROUTER
tristate "Trace data router for MIPI P1149.7 cJTAG standard"
depends on TRACE_SINK
default n
help
The trace router uses the Linux tty line discipline framework to
route trace data coming from a tty port (say UART for example) to
......@@ -329,7 +327,6 @@ config TRACE_ROUTER
config TRACE_SINK
tristate "Trace data sink for MIPI P1149.7 cJTAG standard"
default n
help
The trace sink uses the Linux line discipline framework to receive
trace data coming from the trace router line discipline driver
......
......@@ -25,7 +25,6 @@ config HVC_CONSOLE
config HVC_OLD_HVSI
bool "Old driver for pSeries serial port (/dev/hvsi*)"
depends on HVC_CONSOLE
default n
config HVC_OPAL
bool "OPAL Console support"
......@@ -74,7 +73,6 @@ config HVC_UDBG
bool "udbg based fake hypervisor console"
depends on PPC
select HVC_DRIVER
default n
help
This is meant to be used during HW bring up or debugging when
no other console mechanism exist but udbg, to get you a quick
......
......@@ -370,7 +370,6 @@ config SERIAL_MAX310X
depends on SPI_MASTER
select SERIAL_CORE
select REGMAP_SPI if SPI_MASTER
default n
help
This selects support for an advanced UART from Maxim (Dallas).
Supported ICs are MAX3107, MAX3108, MAX3109, MAX14830.
......@@ -653,7 +652,6 @@ config SERIAL_MUX_CONSOLE
config PDC_CONSOLE
bool "PDC software console support"
depends on PARISC && !SERIAL_MUX && VT
default n
help
Saying Y here will enable the software based PDC console to be
used as the system console. This is useful for machines in
......@@ -1110,7 +1108,6 @@ config SERIAL_QE
depends on QUICC_ENGINE
select SERIAL_CORE
select FW_LOADER
default n
help
This driver supports the QE serial ports on Freescale embedded
PowerPC that contain a QUICC Engine.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment