SERIAL: omap: move driver private definitions and structures to driver

struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm.  Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/plat-omap/include/plat/omap-serial.h

@@ -30,35 +30,9 @@
  */
 #define OMAP_SERIAL_NAME	"ttyO"
 
-#define OMAP_MODE13X_SPEED	230400
-
-#define OMAP_UART_SCR_TX_EMPTY	0x08
-
-/* WER = 0x7F
- * Enable module level wakeup in WER reg
- */
-#define OMAP_UART_WER_MOD_WKUP	0X7F
-
-/* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX		0x04
-
-/* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX		0x04
-
 #define OMAP_UART_SYSC_RESET	0X07
-#define OMAP_UART_TCR_TRIG	0X0F
-#define OMAP_UART_SW_CLR	0XF0
 #define OMAP_UART_FIFO_CLR	0X06
 
-#define OMAP_UART_DMA_CH_FREE	-1
-
-#define OMAP_MAX_HSUART_PORTS	6
-
-#define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
-
-#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
-#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
-
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
@@ -77,30 +51,4 @@ struct omap_uart_port_info {
 	void (*enable_wakeup)(struct device *, bool);
 };
 
-struct uart_omap_dma {
-	u8			uart_dma_tx;
-	u8			uart_dma_rx;
-	int			rx_dma_channel;
-	int			tx_dma_channel;
-	dma_addr_t		rx_buf_dma_phys;
-	dma_addr_t		tx_buf_dma_phys;
-	unsigned int		uart_base;
-	/*
-	 * Buffer for rx dma.It is not required for tx because the buffer
-	 * comes from port structure.
-	 */
-	unsigned char		*rx_buf;
-	unsigned int		prev_rx_dma_pos;
-	int			tx_buf_size;
-	int			tx_dma_used;
-	int			rx_dma_used;
-	spinlock_t		tx_lock;
-	spinlock_t		rx_lock;
-	/* timer to poll activity on rx dma */
-	struct timer_list	rx_timer;
-	unsigned int		rx_buf_size;
-	unsigned int		rx_poll_rate;
-	unsigned int		rx_timeout;
-};
-
 #endif /* __OMAP_SERIAL_H__ */

drivers/tty/serial/omap-serial.c

@@ -44,6 +44,8 @@
 
 #include <plat/omap-serial.h>
 
+#define OMAP_MAX_HSUART_PORTS	6
+
 #define UART_BUILD_REVISION(x, y)	(((x) << 8) | (y))
 
 #define OMAP_UART_REV_42 0x0402
@@ -51,10 +53,14 @@
 #define OMAP_UART_REV_52 0x0502
 #define OMAP_UART_REV_63 0x0603
 
+#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
+#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
+
 #define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
 
 /* SCR register bitmasks */
 #define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK		(1 << 7)
+#define OMAP_UART_SCR_TX_EMPTY			(1 << 3)
 
 /* FCR register bitmasks */
 #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK			(0x3 << 6)
@@ -71,6 +77,52 @@
 #define OMAP_UART_MVR_MAJ_SHIFT		8
 #define OMAP_UART_MVR_MIN_MASK		0x3f
 
+#define OMAP_UART_DMA_CH_FREE	-1
+
+#define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
+#define OMAP_MODE13X_SPEED	230400
+
+/* WER = 0x7F
+ * Enable module level wakeup in WER reg
+ */
+#define OMAP_UART_WER_MOD_WKUP	0X7F
+
+/* Enable XON/XOFF flow control on output */
+#define OMAP_UART_SW_TX		0x4
+
+/* Enable XON/XOFF flow control on input */
+#define OMAP_UART_SW_RX		0x4
+
+#define OMAP_UART_SW_CLR	0xF0
+
+#define OMAP_UART_TCR_TRIG	0x0F
+
+struct uart_omap_dma {
+	u8			uart_dma_tx;
+	u8			uart_dma_rx;
+	int			rx_dma_channel;
+	int			tx_dma_channel;
+	dma_addr_t		rx_buf_dma_phys;
+	dma_addr_t		tx_buf_dma_phys;
+	unsigned int		uart_base;
+	/*
+	 * Buffer for rx dma.It is not required for tx because the buffer
+	 * comes from port structure.
+	 */
+	unsigned char		*rx_buf;
+	unsigned int		prev_rx_dma_pos;
+	int			tx_buf_size;
+	int			tx_dma_used;
+	int			rx_dma_used;
+	spinlock_t		tx_lock;
+	spinlock_t		rx_lock;
+	/* timer to poll activity on rx dma */
+	struct timer_list	rx_timer;
+	unsigned int		rx_buf_size;
+	unsigned int		rx_poll_rate;
+	unsigned int		rx_timeout;
+};
+
 struct uart_omap_port {
 	struct uart_port	port;
 	struct uart_omap_dma	uart_dma;