After fixes to the rs algorithm reenable MCS9.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows mac80211 to flush the Tx queues before it sends
critical management frames.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some ampdu actions change queues by direct target access.

Since the bus is disabled in d0i3, make sure to exit d0i3
before handling these actions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When a firmware error occurs, capture the last 32 commands
(which are still in memory) in the error dump debugfs file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This variable always tracks a constant value (256) so there's
no need to have it. Removing it simplifies code generation,
reducing the .text size (by about 240 bytes on x86-64.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The 'reset' argument is clearly a boolean, so use bool instead
of u8 with 0/1 values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The old code checks if hw_section_num is valid while the
right thing to do is to check if section[hw_section_num].data
is valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

OTP size changed in family 7000 and in family 8000.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to use a variable just to return the result
of another function call at the end of a function, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.

Fix this by using the sta bandwidth when deciding which table to choose.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

TPC is a power optimization which should only be attempted when
we're in the "stay in column" state after we've locked onto an optimal
rate.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

My bad - I forgot to update this when sending the patch
upstream.

Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below introduced a bug in the validity bits in
init. Due to that, all the Coex mechanism stopped sending
kills to the BT side. Fix that.

Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Jahnavi Meher <jahnavi.meher@redpinesignals.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adjust FIR filter co-efficients to improve EVM for 11b rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

 * rfsat gainchange hysteresis of rf_gain stuck with large
   interference present.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use a newline character appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Coverity CID 986698 reports leakage of struct wlcore_platdev_data in the
probe functions of both the SPI/SDIO interfaces. The structure passed to
platform_device_add_data() is dynamically allocated and only freed in the
error paths, however, platform_device_add_data() adds a copy of the platform
specific data to the device. Move the temporary struct that is kmemdup'ed
to the stack. This issue exists since afb43e6d (wlcore: remove if_ops from
platform_data).
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

94010fa0 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 2a54eb5e
("rtlwifi: rtl8188ee: enable MSI interrupts mode").

94010fa0 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.

So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.

BugLink: https://bugs.launchpad.net/bugs/1310512Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setting it to true during init doesn't seem to be any workaround while
it can cause problems (not enabling radio due to belief it's enabled).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes dealing with pointers directly and allows tracking radio
state with radio_on variable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	net/mac80211/chan.c

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Implement the new cfg80211 capability to enable mac80211-based drivers
to support for dynamic channel bandwidth changes (e.g., HT 20/40 MHz
changes).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>