- 20 Sep, 2017 8 commits
-
-
Meng Xu authored
In isdn_ppp_write(), the header (i.e., protobuf) of the buffer is fetched twice from userspace. The first fetch is used to peek at the protocol of the message and reset the huptimer if necessary; while the second fetch copies in the whole buffer. However, given that buf resides in userspace memory, a user process can race to change its memory content across fetches. By doing so, we can either avoid resetting the huptimer for any type of packets (by first setting proto to PPP_LCP and later change to the actual type) or force resetting the huptimer for LCP packets. This patch changes this double-fetch behavior into two single fetches decided by condition (lp->isdn_device < 0 || lp->isdn_channel <0). A more detailed discussion can be found at https://marc.info/?l=linux-kernel&m=150586376926123&w=2Signed-off-by:
Meng Xu <mengxu.gatech@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Troy Kisky authored
fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused an interrupt. Don't return IRQ_NONE in this case. Signed-off-by:
Troy Kisky <troy.kisky@boundarydevices.com> Acked-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
-
Troy Kisky authored
FEC_ENET_TS_TIMER is not checked in the interrupt routine so there is no need to enable it. Signed-off-by:
-
Troy Kisky authored
Before queue 0 was always checked if any queue caused an interrupt. It is better to just mark queue 0 if queue 0 has caused an interrupt. Signed-off-by:
-
Edward Cree authored
Since XDP's view of the packet includes the MAC header, moving the start- of-packet with bpf_xdp_adjust_head needs to also update the offset of the MAC header (which is relative to skb->head, not to the skb->data that was changed). Without this, tcpdump sees packets starting from the old MAC header rather than the new one, at least in my tests on the loopback device. Fixes: b5cdae32 ("net: Generic XDP") Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Meng Xu authored
The actual length of cmsg fetched in during the second loop (i.e., kcmsg - kcmsg_base) could be different from what we get from the first loop (i.e., kcmlen). The main reason is that the two get_user() calls in the two loops (i.e., get_user(ucmlen, &ucmsg->cmsg_len) and __get_user(ucmlen, &ucmsg->cmsg_len)) could cause ucmlen to have different values even they fetch from the same userspace address, as user can race to change the memory content in &ucmsg->cmsg_len across fetches. Although in the second loop, the sanity check if ((char *)kcmsg_base + kcmlen - (char *)kcmsg < CMSG_ALIGN(tmp)) is inplace, it only ensures that the cmsg fetched in during the second loop does not exceed the length of kcmlen, but not necessarily equal to kcmlen. But indicated by the assignment kmsg->msg_controllen = kcmlen, we should enforce that. This patch adds this additional sanity check and ensures that what is recorded in kmsg->msg_controllen is the actual cmsg length. Signed-off-by:
-
Yonghong Song authored
This patch fixes a bug exhibited by the following scenario: 1. fd1 = perf_event_open with attr.config = ID1 2. attach bpf program prog1 to fd1 3. fd2 = perf_event_open with attr.config = ID1 <this will be successful> 4. user program closes fd2 and prog1 is detached from the tracepoint. 5. user program with fd1 does not work properly as tracepoint no output any more. The issue happens at step 4. Multiple perf_event_open can be called successfully, but only one bpf prog pointer in the tp_event. In the current logic, any fd release for the same tp_event will free the tp_event->prog. The fix is to free tp_event->prog only when the closing fd corresponds to the one which registered the program. Signed-off-by:Yonghong Song <yhs@fb.com> Signed-off-by:
-
Willem de Bruijn authored
Packet socket bind operations must hold the po->bind_lock. This keeps po->running consistent with whether the socket is actually on a ptype list to receive packets. fanout_add unbinds a socket and its packet_rcv/tpacket_rcv call, then binds the fanout object to receive through packet_rcv_fanout. Make it hold the po->bind_lock when testing po->running and rebinding. Else, it can race with other rebind operations, such as that in packet_set_ring from packet_rcv to tpacket_rcv. Concurrent updates can result in a socket being added to a fanout group twice, causing use-after-free KASAN bug reports, among others. Reported independently by both trinity and syzkaller. Verified that the syzkaller reproducer passes after this patch. Fixes: dc99f600 ("packet: Add fanout support.") Reported-by:
nixioaming <nixiaoming@huawei.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
- 19 Sep, 2017 21 commits
-
-
Matteo Croce authored
Currently, writing into net.ipv6.conf.all.{accept_dad,use_optimistic,optimistic_dad} has no effect. Fix handling of these flags by: - using the maximum of global and per-interface values for the accept_dad flag. That is, if at least one of the two values is non-zero, enable DAD on the interface. If at least one value is set to 2, enable DAD and disable IPv6 operation on the interface if MAC-based link-local address was found - using the logical OR of global and per-interface values for the optimistic_dad flag. If at least one of them is set to one, optimistic duplicate address detection (RFC 4429) is enabled on the interface - using the logical OR of global and per-interface values for the use_optimistic flag. If at least one of them is set to one, optimistic addresses won't be marked as deprecated during source address selection on the interface. While at it, as we're modifying the prototype for ipv6_use_optimistic_addr(), drop inline, and let the compiler decide. Fixes: 7fd2561e ("net: ipv6: Add a sysctl to make optimistic addresses useful candidates") Signed-off-by:Matteo Croce <mcroce@redhat.com> Signed-off-by:
-
Mike Manning authored
Commit f784ad3d ("ipv6: do not send RTM_DELADDR for tentative addresses") incorrectly assumes that no RTM_NEWADDR are sent for addresses in tentative state, as this does happen for the standard IPv6 use-case of DAD failure, see the call to ipv6_ifa_notify() in addconf_dad_stop(). So as a result of this change, no RTM_DELADDR is sent after DAD failure for a link-local when strict DAD (accept_dad=2) is configured, or on the next admin down in other cases. The absence of this notification breaks backwards compatibility and causes problems after DAD failure if this notification was being relied on. The solution is to allow RTM_DELADDR to still be sent after DAD failure. Fixes: f784ad3d ("ipv6: do not send RTM_DELADDR for tentative addresses") Signed-off-by:
Mike Manning <mmanning@brocade.com> Cc: Mahesh Bandewar <maheshb@google.com> Signed-off-by:
-
Daniel Borkmann authored
Commit 109980b8 ("bpf: don't select potentially stale ri->map from buggy xdp progs") passed the pointer to the prog itself to be loaded into r4 prior on bpf_redirect_map() helper call, so that we can store the owner into ri->map_owner out of the helper. Issue with that is that the actual address of the prog is still subject to change when subsequent rewrites occur that require slow path in bpf_prog_realloc() to alloc more memory, e.g. from patching inlining helper functions or constant blinding. Thus, we really need to take prog->aux as the address we're holding, which also works with prog clones as they share the same aux object. Instead of then fetching aux->prog during runtime, which could potentially incur cache misses due to false sharing, we are going to just use aux for comparison on the map owner. This will also keep the patchlet of the same size, and later check in xdp_map_invalid() only accesses read-only aux pointer from the prog, it's also in the same cacheline already from prior access when calling bpf_func. Fixes: 109980b8 ("bpf: don't select potentially stale ri->map from buggy xdp progs") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Christian Lamparter authored
This patch is pretty much a carbon copy of commit 3079c652 ("caif: Fix napi poll list corruption") with "caif" replaced by "emac". The commit d75b1ade ("net: less interrupt masking in NAPI") breaks emac. It is now required that if the entire budget is consumed when poll returns, the napi poll_list must remain empty. However, like some other drivers emac tries to do a last-ditch check and if there is more work it will call napi_reschedule and then immediately process some of this new work. Should the entire budget be consumed while processing such new work then we will violate the new caller contract. This patch fixes this by not touching any work when we reschedule in emac. Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Eric Dumazet authored
Our recent change exposed a bug in TCP Fastopen Client that syzkaller found right away [1] When we prepare skb with SYN+DATA, we attempt to transmit it, and we update socket state as if the transmit was a success. In socket RTX queue we have two skbs, one with the SYN alone, and a second one containing the DATA. When (malicious) ACK comes in, we now complain that second one had no skb_mstamp. The proper fix is to make sure that if the transmit failed, we do not pretend we sent the DATA skb, and make it our send_head. When 3WHS completes, we can now send the DATA right away, without having to wait for a timeout. [1] WARNING: CPU: 0 PID: 100189 at net/ipv4/tcp_input.c:3117 tcp_clean_rtx_queue+0x2057/0x2ab0 net/ipv4/tcp_input.c:3117() WARN_ON_ONCE(last_ackt == 0); Modules linked in: CPU: 0 PID: 100189 Comm: syz-executor1 Not tainted Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 0000000000000000 ffff8800b35cb1d8 ffffffff81cad00d 0000000000000000 ffffffff828a4347 ffff88009f86c080 ffffffff8316eb20 0000000000000d7f ffff8800b35cb220 ffffffff812c33c2 ffff8800baad2440 00000009d46575c0 Call Trace: [<ffffffff81cad00d>] __dump_stack [<ffffffff81cad00d>] dump_stack+0xc1/0x124 [<ffffffff812c33c2>] warn_slowpath_common+0xe2/0x150 [<ffffffff812c361e>] warn_slowpath_null+0x2e/0x40 [<ffffffff828a4347>] tcp_clean_rtx_queue+0x2057/0x2ab0 n [<ffffffff828ae6fd>] tcp_ack+0x151d/0x3930 [<ffffffff828baa09>] tcp_rcv_state_process+0x1c69/0x4fd0 [<ffffffff828efb7f>] tcp_v4_do_rcv+0x54f/0x7c0 [<ffffffff8258aacb>] sk_backlog_rcv [<ffffffff8258aacb>] __release_sock+0x12b/0x3a0 [<ffffffff8258ad9e>] release_sock+0x5e/0x1c0 [<ffffffff8294a785>] inet_wait_for_connect [<ffffffff8294a785>] __inet_stream_connect+0x545/0xc50 [<ffffffff82886f08>] tcp_sendmsg_fastopen [<ffffffff82886f08>] tcp_sendmsg+0x2298/0x35a0 [<ffffffff82952515>] inet_sendmsg+0xe5/0x520 [<ffffffff8257152f>] sock_sendmsg_nosec [<ffffffff8257152f>] sock_sendmsg+0xcf/0x110 Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully") Fixes: 783237e8 ("net-tcp: Fast Open client - sending SYN-data") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
David S. Miller authored
Salil Mehta says: ==================== Bug fixes for the HNS3 Ethernet Driver for Hip08 SoC This patch set presents some bug fixes for the HNS3 Ethernet driver identified during internal testing & stabilization efforts. Change Log: Patch V2: Resolved comments from Leon Romanovsky Patch V1: Initial Submit ==================== Signed-off-by: -
Lipeng authored
When register/unregister ae_dev, ae_dev should match all client in the client_list. Enet and roce can co-exists together so we should continue checking for enet and roce presence together. So break should not be there. Above caused problems in loading and unloading of modules. Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework") Signed-off-by:Lipeng <lipeng321@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
-
Lipeng authored
When there is no vlan id in the packets, hardware will treat the vlan id as 0 and look for the mac_vlan table. This patch set the default vlan id of PF as 0. Without this config, it will fail when look for mac_vlan table, and hardware will drop packets. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:Mingguang Qu <qumingguang@huawei.com> Signed-off-by:
-
Salil Mehta authored
This patch replaces the ethernet address copy instance with more appropriate ether_addr_copy() function. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: -
Lipeng authored
This patch fixes the initialization of MAC address, fetched from HNS3 firmware i.e. when it is not randomly generated, to the HNS3 hardware. Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: -
Lipeng authored
This patch fixes the vector-to-ring map and unmap command and adds INT_GL(for, Gap Limiting Interrupts) and VF id to it as required by the hardware interface. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: -
Lipeng authored
This patch fixes the IMP command being used to unmap the vector from the corresponding ring. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: -
Lipeng authored
Default phy address of every port is 0. Therefore, phy address for each port need to be fetched from firmware and device initialized with fetched non-default phy address. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: -
Eric Dumazet authored
syzkaller reported following splat [1] Since hard irq are disabled by the caller, bpf_map_free_id() should not try to enable/disable BH. Another solution would be to change htab_map_delete_elem() to defer the free_htab_elem() call after raw_spin_unlock_irqrestore(&b->lock, flags), but this might be not enough to cover other code paths. [1] WARNING: CPU: 1 PID: 8052 at kernel/softirq.c:161 __local_bh_enable_ip +0x1e/0x160 kernel/softirq.c:161 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 8052 Comm: syz-executor1 Not tainted 4.13.0-next-20170915+ #23 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x194/0x257 lib/dump_stack.c:52 panic+0x1e4/0x417 kernel/panic.c:181 __warn+0x1c4/0x1d9 kernel/panic.c:542 report_bug+0x211/0x2d0 lib/bug.c:183 fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178 do_trap_no_signal arch/x86/kernel/traps.c:212 [inline] do_trap+0x260/0x390 arch/x86/kernel/traps.c:261 do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311 invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905 RIP: 0010:__local_bh_enable_ip+0x1e/0x160 kernel/softirq.c:161 RSP: 0018:ffff8801cdcd7748 EFLAGS: 00010046 RAX: 0000000000000082 RBX: 0000000000000201 RCX: 0000000000000000 RDX: 1ffffffff0b5933c RSI: 0000000000000201 RDI: ffffffff85ac99e0 RBP: ffff8801cdcd7758 R08: ffffffff85b87158 R09: 1ffff10039b9aec6 R10: ffff8801c99f24c0 R11: 0000000000000002 R12: ffffffff817b0b47 R13: dffffc0000000000 R14: ffff8801cdcd77e8 R15: 0000000000000001 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:176 [inline] _raw_spin_unlock_bh+0x30/0x40 kernel/locking/spinlock.c:207 spin_unlock_bh include/linux/spinlock.h:361 [inline] bpf_map_free_id kernel/bpf/syscall.c:197 [inline] __bpf_map_put+0x267/0x320 kernel/bpf/syscall.c:227 bpf_map_put+0x1a/0x20 kernel/bpf/syscall.c:235 bpf_map_fd_put_ptr+0x15/0x20 kernel/bpf/map_in_map.c:96 free_htab_elem+0xc3/0x1b0 kernel/bpf/hashtab.c:658 htab_map_delete_elem+0x74d/0x970 kernel/bpf/hashtab.c:1063 map_delete_elem kernel/bpf/syscall.c:633 [inline] SYSC_bpf kernel/bpf/syscall.c:1479 [inline] SyS_bpf+0x2188/0x46a0 kernel/bpf/syscall.c:1451 entry_SYSCALL_64_fastpath+0x1f/0xbe Fixes: f3f1c054 ("bpf: Introduce bpf_map ID") Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Acked-by:
-
Andreas Gruenbacher authored
Clarify that rhashtable_walk_{stop,start} will not reset the iterator to the beginning of the hash table. Confusion between rhashtable_walk_enter and rhashtable_walk_start has already lead to a bug. Signed-off-by:Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by:
-
Jerome Brunet authored
Since the integration of PHYLINK, the configuration option which used to be under the PHY infrastructure menu in menuconfig ended up one level up (the network device driver section) By placing PHYLINK option right after PHYLIB entry, it broke the way Kconfig used to build the menu. See kconfig-language.txt, section "Menu structure", 2nd method. This is fixed by placing the PHYLINK option just before PHYLIB. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by:
Jerome Brunet <jbrunet@baylibre.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'mac80211-for-davem-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Just two netlink fixes, both allowing privileged users to crash the kernel with malformed netlink messages. ==================== Signed-off-by:
-
Ariel Elior authored
Remove Yuval from maintaining the bnx2x & qed* modules as he is no longer working for the company. Thanks Yuval for your huge contributions and tireless efforts over the many years and various companies. Ariel Signed-off-by:
Ariel Elior <aelior@cavium.com> Signed-off-by:
-
Florian Fainelli authored
There are several problems with commit 10377ba7 ("net: systemport: Support 64bit statistics", first one got fixed in 7095c973 ("net: systemport: Fix 64-bit stats deadlock"). The second problem is that this specific code updates the stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we are returning to ethtool -S. If we are not running a tool that involves calling ndo_get_stats64(), then we won't get updated ethtool stats. The solution to this is to update the stats from both call sites, factoring that into a specific function, While at it, don't just check the sizeof() but also the type of the statistics in order to use the 64-bit stats seqlock. Fixes: 10377ba7 ("net: systemport: Support 64bit statistics") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Eric Dumazet authored
It seems we have to be more careful in napi_complete_done() use. This patch is not a revert, as it seems we can avoid bug that Ville reported by moving the napi_complete_done() test in the spinlock section. Many thanks to Ville for detective work and all tests. Fixes: 617f0121 ("8139too: use napi_complete_done()") Reported-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by:
-
Yuchung Cheng authored
remove tcp_may_send_now and tcp_snd_test that are no longer used Fixes: 840a3cbe ("tcp: remove forward retransmit feature") Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
- 18 Sep, 2017 9 commits
-
-
Tobias Klauser authored
If bpf_map_precharge_memlock in dev_map_alloc, -ENOMEM is returned regardless of the actual error produced by bpf_map_precharge_memlock. Fix it by passing on the error returned by bpf_map_precharge_memlock. Also return -EINVAL instead of -ENOMEM if the page count overflow check fails. This makes dev_map_alloc match the behavior of other bpf maps' alloc functions wrt. return values. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Acked-by:
-
Sathya Perla authored
Check for ingress-only qdisc for flower offload, as other qdiscs are not supported for flower offload. Suggested-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Sathya Perla <sathya.perla@broadcom.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Randy Dunlap authored
Fix ASCII art in Documentation/networking/switchdev.txt: Change non-ASCII "spaces" to ASCII spaces. Change 2 erroneous '+' characters in ASCII art to '-' (at the '*' characters below): line 32: +--+----+----+----+-*--+----+---+ +-----+-----+ line 41: +--------------+---*------------+ Signed-off-by:Randy Dunlap <rdunlap@infradead.org> Acked-by:
Pavel Machek <pavel@ucw.cz> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Davide Caratti authored
this script, edited from Linux Advanced Routing and Traffic Control guide tc q a dev en0 root handle 1: htb default a tc c a dev en0 parent 1: classid 1:1 htb rate 6mbit burst 15k tc c a dev en0 parent 1:1 classid 1:a htb rate 5mbit ceil 6mbit burst 15k tc c a dev en0 parent 1:1 classid 1:b htb rate 1mbit ceil 6mbit burst 15k tc f a dev en0 parent 1:0 prio 1 $clsname $clsargs classid 1:b ping $address -c1 tc -s c s dev en0 classifies traffic to 1:b or 1:a, depending on whether the packet matches or not the pattern $clsargs of filter $clsname. However, when $clsname is 'matchall', a systematic crash can be observed in htb_classify(). HTB and classful qdiscs don't assign initial value to struct tcf_result, but then they expect it to contain valid values after filters have been run. Thus, current 'matchall' ignores the TCA_MATCHALL_CLASSID attribute, configured by user, and makes HTB (and classful qdiscs) dereference random pointers. By assigning head->res to *res in mall_classify(), before the actions are invoked, we fix this crash and enable TCA_MATCHALL_CLASSID functionality, that had no effect on 'matchall' classifier since its first introduction. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1460213Reported-by:
Jiri Benc <jbenc@redhat.com> Fixes: b87f7936 ("net/sched: introduce Match-all classifier") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Yotam Gigi <yotamg@mellanox.com> Signed-off-by:
-
Xin Long authored
If ipv6 has been disabled from cmdline since kernel started, it makes no sense to allow users to create any ip6 tunnel. Otherwise, it could some potential problem. Jianlin found a kernel crash caused by this in ip6_gre when he set ipv6.disable=1 in grub: [ 209.588865] Unable to handle kernel paging request for data at address 0x00000080 [ 209.588872] Faulting instruction address: 0xc000000000a3aa6c [ 209.588879] Oops: Kernel access of bad area, sig: 11 [#1] [ 209.589062] NIP [c000000000a3aa6c] fib_rules_lookup+0x4c/0x260 [ 209.589071] LR [c000000000b9ad90] fib6_rule_lookup+0x50/0xb0 [ 209.589076] Call Trace: [ 209.589097] fib6_rule_lookup+0x50/0xb0 [ 209.589106] rt6_lookup+0xc4/0x110 [ 209.589116] ip6gre_tnl_link_config+0x214/0x2f0 [ip6_gre] [ 209.589125] ip6gre_newlink+0x138/0x3a0 [ip6_gre] [ 209.589134] rtnl_newlink+0x798/0xb80 [ 209.589142] rtnetlink_rcv_msg+0xec/0x390 [ 209.589151] netlink_rcv_skb+0x138/0x150 [ 209.589159] rtnetlink_rcv+0x48/0x70 [ 209.589169] netlink_unicast+0x538/0x640 [ 209.589175] netlink_sendmsg+0x40c/0x480 [ 209.589184] ___sys_sendmsg+0x384/0x4e0 [ 209.589194] SyS_sendmsg+0xd4/0x140 [ 209.589201] SyS_socketcall+0x3e0/0x4f0 [ 209.589209] system_call+0x38/0xe0 This patch is to return -EOPNOTSUPP in ip6_tunnel_init if ipv6 has been disabled from cmdline. Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Fahad Kunnathadi authored
To clear Speed Selection in MDIO control register(0x10), ie, clear bits 6 and 13 to zero while keeping other bits same. Before AND operation,The Mask value has to be perform with bitwise NOT operation (ie, ~ operator) This patch clears current speed selection before writing the new speed settings to gmii2rgmii converter Fixes: f411a616 ("net: phy: Add gmiitorgmii converter support") Signed-off-by:
Fahad Kunnathadi <fahad.kunnathadi@dexceldesigns.com> Reviewed-by:
-
Xin Long authored
Now in ip6gre_header before packing the ipv6 header, it skb_push t->hlen which only includes encap_hlen + tun_hlen. It means greh and inner header would be over written by ipv6 stuff and ipv6h might have no chance to set up. Jianlin found this issue when using remote any on ip6_gre, the packets he captured on gre dev are truncated: 22:50:26.210866 Out ethertype IPv6 (0x86dd), length 120: truncated-ip6 -\ 8128 bytes missing!(flowlabel 0x92f40, hlim 0, next-header Options (0) \ payload length: 8192) ::1:2000:0 > ::1:0:86dd: HBH [trunc] ip-proto-128 \ 8184 It should also skb_push ipv6hdr so that ipv6h points to the right position to set ipv6 stuff up. This patch is to skb_push hlen + sizeof(*ipv6h) and also fix some indents in ip6gre_header. Fixes: c12b395a ("gre: Support GRE over IPv6") Reported-by:
-
Johannes Berg authored
If TX rates are specified during mesh join, the channel must also be specified. Check the channel pointer to avoid a null pointer dereference if it isn't. Reported-by:
Jouni Malinen <j@w1.fi> Fixes: 8564e382 ("cfg80211: add checks for beacon rate, extend to mesh") Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Subash Abhinov Kasiviswanathan authored
While trying an ESP transport mode encryption for UDPv6 packets of datagram size 1436 with MTU 1500, checksum error was observed in the secondary fragment. This error occurs due to the UDP payload checksum being missed out when computing the full checksum for these packets in udp6_hwcsum_outgoing(). Fixes: d39d938c ("ipv6: Introduce udpv6_send_skb()") Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by:
-
- 16 Sep, 2017 2 commits
-
-
Linus Torvalds authored
-
git://git.infradead.org/linux-ubifsLinus Torvalds authored
Pull UBI updates from Richard Weinberger: "Minor improvements" * tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs: UBI: Fix two typos in comments ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate" ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines
-
