Implement write routine for OCOTP controller found in i.MX6 SoC's.
Furthermore add locking to the read function to prevent race conditions.
The write routine code is based on the fsl_otp driver from Freescale.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When reading a "read locked" value from the OCOTP controller on i.MX6
SoC's an error bit is set. This bit has to be cleared by software before
any new write, read or reload access can be issued.

Therefore clear it after we detect such an "locked read".
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add i.MX7D support.
There is 16 banks, each bank 4 words.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add compatible string for i.MX7D/S
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The IIM is part of the i.MX device trees for long already, add a binding
document for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a readonly nvmem driver for the i.MX IC Identification Module
(IIM). The IIM is found on the older i.MX SoCs like the i.MX25, i.MX27,
i.MX31, i.MX35, i.MX51 and the i.MX53.

The IIM can control up to 8 fuse banks with 256 bit each. Not all of the
banks are equipped on the different SoCs. The actual number of fuses
differ from 512 on the i.MX27 and 1152 on the i.MX53.

The fuses are one time writable, but writing is currently not supported
in the driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Assign the correct dev pointer to struct ocotp_priv during probe. This
is needed to display dev_* messages correctly. Furthermore harmonize
the usage of dev (instead of &pdev->dev) in the probe function.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The H3 SoC have a bigger SID controller, which has its direct read
address at 0x200 position in the SID block, not 0x0.

Also, H3 SID controller has some silicon bug that makes the direct read
value wrong at cold boot, add code to workaround the bug. (This bug has
already been fixed on A64 and later SoCs)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes the SID device have more memory address space than the real
NVMEM size (for the registers used to read/write the SID).

Fetch the NVMEM size from device compatible, rather than the memory
address space's length, in order to prepare for adding some
registers-based read support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the nvmem core expect the config to provide a name and ID
that are then used to create the device name. When no device name is
given 'nvmem' is used. However if there is several such anonymous
devices they all get named 'nvmem0', which doesn't work.

To fix this problem use the ID from the config only when the config
also provides a name. When no name is provided take the uinque ID of
the nvmem device instead.
Signed-off-by: Aban Bedel <albeu@free.fr>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I've never been really been maintaining nvmem, so make that official.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for the Xilinx LogiCORE PR Decoupler
soft-ip that does decoupling of PR regions in the FPGA
fabric during partial reconfiguration.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It looks like arm-charlcd.c belongs to auxdisplay subsystem.

Move it to drivers/auxdisplay folder.
No functional changes intended.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It looks like panel.c belongs to auxdisplay subsystem.

Move it to drivers/auxdisplay folder.
No functional changes intended.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The data read from the device is 3 little-endian words, so let's
annotate them as such and use le16_to_cpu() to convert them to host
endianness - it might turn out to be a bit more performant, and it
expresses the conversion more clearly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/auxdisplay/img-ascii-lcd.ko | grep alias
$

After this patch:

$ modinfo drivers/auxdisplay/img-ascii-lcd.ko | grep alias
alias:          of:N*T*Cmti,sead3-lcdC*
alias:          of:N*T*Cmti,sead3-lcd
alias:          of:N*T*Cmti,malta-lcdC*
alias:          of:N*T*Cmti,malta-lcd
alias:          of:N*T*Cimg,boston-lcdC*
alias:          of:N*T*Cimg,boston-lcd
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gcc-7.0.1 points out that we copy uninitialized data from the stack
into a per-device structure:

drivers/auxdisplay/ht16k33.c: In function 'ht16k33_keypad_irq_thread':
arch/x86/include/asm/string_32.h:78:16: error: 'new_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:79:22: error: '*((void *)&new_state+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The access is harmless because we never read the data, but we are better
off not doing this, so this changes the code to only copy the data
that was actually initialized. To make sure we don't overflow the
stack with an incorrect DT, we also need to add a sanity checkin the
probe function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Robin van der Gracht <robin@protonic.nl>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DT properties specifying physical properties should contain appropriate
suffices indicating the units of measurement.

Hence amend the HD44780 DT bindings to add "chars" suffixes to the
"display-height" and "display-width" properties, and update the driver
to parse them.

Fixes: dd9502a9 ("dt-bindings: auxdisplay: Add bindings for Hitachi HD44780")
Fixes: d47d8836 ("auxdisplay: Add HD44780 Character LCD support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A few updates:
* Updating my email address
* Adding another docs directory: Documentation/fpga
* Making the include path not specific to fpga-mgr.h only
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Moritz Fischer <moritz.fischer@ettus.com>
Cc: linux-fpga@vger.kernel.org
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a platform bus driver for a fpga-mgr driver
that uses the Altera Partial Reconfiguration IP component.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Device Tree bindings for Altera Partial Reconfiguration IP.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding the core functions necessary for a fpga-mgr driver
for the Altera Partial IP component.  It is intended for
these functions to be used by the various bus implementations
like the platform bus or the PCIe bus.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding timeout for maximum allowed time for FPGA to go to
operating mode after a FPGA region has been programmed.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver loads FPGA firmware over SPI, using the "slave serial"
configuration interface on Xilinx FPGAs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add dt binding documentation details for Xilinx FPGA configuration
over slave serial interface.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ops are not changing, make them const.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Alan Tull <atull@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-fpga@vger.kernel.org
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Corrected to get the port numbering to allow programmable replicator driver
to operate correctly.

By convention, CoreSight devices number ports, not endpoints in
the .dts files:-

port {
     reg<N>
     endpoint {
     }
}

Existing code read endpoint number - always 0x0, rather than the correct
port number.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When write() returns successfully, it is only assumed that a message
was successfully queued. Add fsync syscall implementation to help
user-space ensure that all data is written.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Though VLA are supported by CC99 there are many cavities
and should be avoided.

'const size_t len = sizeof()' that we used may not be set
at the compile time hence generating VLA code.

This fixes also sparse warning
warning: Variable length array is used type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Though VLA are supported by CC99 there are many cavities
and should be avoided.

'const size_t len = sizeof()' that we used may not be set
at the compile time hence generating VLA code.

This fixes also sparse warning
warning: Variable length array is used type.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

AMTHIF has special support in the mei drive, it handles multiplexing
multiple user space connection above single me client connection.
Since there is no additional addressing information there is a strict
requirement on the traffic order on each connection and on the "read
after write" order within the connection. This creates a lot of
complexity mostly because the other client types do not necessarily fall
under the same restriction.    After carefully studying the use of the
AMTHIF client, we came to conclusion that the multiplexing is not really
utilized by any application and we may safely remove that support and
significantly simplify the driver.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The shutdown handler quiesces the device, it performs link reset in
order to close all connections and notify the device that is not longer
managed by the driver.
This is essentially a stripped down version of the PCI remove() function
where only the necessary amount of work is done to stop any further
activity.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The newly added header file triggers a sanity check:

usr/include/linux/aspeed-lpc-ctrl.h:44: found __[us]{8,16,32,64} type without #include <linux/types.h>

We should include linux/types.h explicitly to ensure the header
can be included from user space.

Fixes: 6c4e9767 ("drivers/misc: Add Aspeed LPC control driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The format string is still broken after the first attempt to fix it:

drivers/misc/aspeed-lpc-ctrl.c: In function 'aspeed_lpc_ctrl_probe':
drivers/misc/aspeed-lpc-ctrl.c:232:17: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]

We can actually just print the resource structure directly here.

Fixes: 132c93d4 ("drivers/misc: Aspeed LPC control fix compile error and warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull char/misc driver fixes from Greg KH:
 "A smattering of different small fixes for some random driver
  subsystems. Nothing all that major, just resolutions for reported
  issues and bugs.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  extcon: int3496: Set the id pin to direction-input if necessary
  extcon: int3496: Use gpiod_get instead of gpiod_get_index
  extcon: int3496: Add dependency on X86 as it's Intel specific
  extcon: int3496: Add GPIO ACPI mapping table
  extcon: int3496: Rename GPIO pins in accordance with binding
  vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
  ppdev: fix registering same device name
  parport: fix attempt to write duplicate procfiles
  auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
  Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
  Drivers: hv: vmbus: Don't leak channel ids
  Drivers: hv: util: don't forget to init host_ts.lock
  Drivers: hv: util: move waiting for release to hv_utils_transport itself
  vmbus: remove hv_event_tasklet_disable/enable
  vmbus: use rcu for per-cpu channel list
  mei: don't wait for os version message reply
  mei: fix deadlock on mei reset
  intel_th: pci: Add Gemini Lake support
  intel_th: pci: Add Denverton SOC support
  intel_th: Don't leak module refcount on failure to activate
  ...

Merge tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single kernfs fix for 4.11-rc4 that resolves a reported
  issue.

  It has been in linux-next with no reported issues"

* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()

Pull tty/serial driver fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.11-rc4.

  One of these fix a long-standing issue in the ldisc code that was
  found by Dmitry Vyukov with his great fuzzing work. The other fixes
  resolve other reported issues, and there is one revert of a patch in
  4.11-rc1 that wasn't correct.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: fix data race in tty_ldisc_ref_wait()
  tty: don't panic on OOM in tty_set_ldisc()
  Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
  tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
  serial: 8250_dw: Fix breakage when HAVE_CLK=n
  serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios