An error occurred fetching the project authors.
- 04 May, 2016 1 commit
-
-
Lyude authored
Right now MST audio is causing too many kernel panics to really keep around in the kernel. On top of that, even after fixing said panics it's still basically non-functional (at least on all the setups I've tested it on). Revert until we have a proper solution for this. This reverts commit 3d52ccf5. Signed-off-by: Lyude <cpaul@redhat.com> Fixes: 3d52ccf5 ("drm/i915: start adding dp mst audio") Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1462287692-28570-1-git-send-email-cpaul@redhat.com (cherry picked from commit 5a8f97ea) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 27 Apr, 2016 2 commits
-
-
Mika Kahola authored
It was noticed on bug #94087 that module parameter i915.edp_vswing=2 that should override the VBT setting to use default voltage swing (400 mV) was not applied for Broadwell. This patch provides a fix for this by checking if default i.e. higher voltage swing is requested to be used and applies the DDI translations table for DP instead of eDP (low vswing) table. v2: Combine two if statements into one (Jani) v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087Signed-off-by: Mika Kahola <mika.kahola@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com Cc: stable@vger.kernel.org Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (cherry picked from commit 00983519) [Jani: s/dev_priv->vbt.edp.low_vswing/dev_priv->edp_low_vswing/ to backport] Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
Imre Deak authored
The driver's VDD on/off logic assumes that whenever the VDD is on we also hold an AUX power domain reference. Since BIOS can leave the VDD on during booting and resuming and on DDI platforms we won't take a corresponding power reference, the above assumption won't hold on those platforms and an eventual delayed VDD off work will do an extraneous AUX power domain put resulting in a refcount underflow. Fix this the same way we did this for non-DDI DP encoders: commit 6d93c0c4 ("drm/i915: fix VDD state tracking after system resume") At the same time call the DP encoder suspend handler the same way as the non-DDI DP encoders do to flush any pending VDD off work. Leaving the work running may cause a HW access where we don't expect this (at a point where power domains are suspended already). While at it remove an unnecessary function call indirection. This fixed for me AUX refcount underflow problems on BXT during suspend/resume. CC: Ville Syrjälä <ville.syrjala@linux.intel.com> CC: stable@vger.kernel.org Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com (cherry picked from commit bf93ba67) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 07 Mar, 2016 1 commit
-
-
Takashi Iwai authored
The recent commit [0bdf5a05: drm/i915: Add reverse mapping between port and intel_encoder] introduced a reverse mapping to retrieve intel_dig_port object from the port number. The code assumed that the port vs intel_dig_port are 1:1 mapping. But in reality, this was a too naive assumption. As Martin reported about the missing HDMI audio on his SNB machine, pre-HSW chips may have multiple intel_dig_port objects corresponding to the same port. Since we assign the mapping statically at the init time and the multiple objects override the map, it may not match with the actually enabled output. This patch tries to address the regression above. The reverse mapping is provided basically only for the audio callbacks, so now we set / clear the mapping dynamically at enabling and disabling HDMI/DP audio, so that we can always track the latest and correct object corresponding to the given port. Fixes: 0bdf5a05 ('drm/i915: Add reverse mapping between port and intel_encoder') Reported-and-tested-by: Martin Kepplinger <martink@posteo.de> Cc: drm-intel-fixes@lists.freedesktop.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1456324522-21591-1-git-send-email-tiwai@suse.de (cherry picked from commit 9dfbffcf) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 22 Feb, 2016 1 commit
-
-
Imre Deak authored
The assumption when adding the intel_display_power_is_enabled() checks was that if it returns success the power can't be turned off afterwards during the HW access, which is guaranteed by modeset locks. This isn't always true, so make sure we hold a dedicated reference for the time of the access. CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com (cherry picked from commit e27daab4) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 17 Feb, 2016 1 commit
-
-
Imre Deak authored
The assumption when adding the intel_display_power_is_enabled() checks was that if it returns success the power can't be turned off afterwards during the HW access, which is guaranteed by modeset locks. This isn't always true, so make sure we hold a dedicated reference for the time of the access. CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com
-
- 10 Feb, 2016 1 commit
-
-
Lyude authored
We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a result we skip assigning a DPLL to any DP MST ports, which makes link training fail: [ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well [ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well [ 1442.933957] [drm:intel_mst_pre_enable_dp] 0 [ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000 [ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0 [ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0 [ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000 [ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1 [ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1 [ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000 [ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2 … [ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up [ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting After which the pipe state goes completely out of sync: [ 70.075596] [drm:check_crtc_state] [CRTC:25] [ 70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001) [ 70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0) [ 70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021) [ 70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173) [ 70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5) [ 70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256) [ 70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500) And if you're especially lucky, it keeps going downhill: [ 83.309256] Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler [ 83.309265] [ 83.309265] ================================= [ 83.309266] [ INFO: inconsistent lock state ] [ 83.309267] 4.5.0-rc1Lyude-Test #265 Not tainted [ 83.309267] --------------------------------- [ 83.309268] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. [ 83.309270] Xorg/1194 [HC0[1]:SC0[0]:HE1:SE1] takes: [ 83.309293] (&(&dev_priv->uncore.lock)->rlock){?.-...}, at: [<ffffffffa02a6073>] gen9_write32+0x63/0x400 [i915] [ 83.309293] {IN-HARDIRQ-W} state was registered at: [ 83.309297] [<ffffffff810e84f4>] __lock_acquire+0x9c4/0x1d00 [ 83.309299] [<ffffffff810ea1be>] lock_acquire+0xce/0x1c0 [ 83.309302] [<ffffffff8177d936>] _raw_spin_lock_irqsave+0x56/0x90 [ 83.309321] [<ffffffffa02a5492>] gen9_read32+0x52/0x3d0 [i915] [ 83.309332] [<ffffffffa024beea>] gen8_irq_handler+0x27a/0x6a0 [i915] [ 83.309337] [<ffffffff810fdbc1>] handle_irq_event_percpu+0x41/0x300 [ 83.309339] [<ffffffff810fdeb9>] handle_irq_event+0x39/0x60 [ 83.309341] [<ffffffff811010b4>] handle_edge_irq+0x74/0x130 [ 83.309344] [<ffffffff81009073>] handle_irq+0x73/0x120 [ 83.309346] [<ffffffff817805f1>] do_IRQ+0x61/0x120 [ 83.309348] [<ffffffff8177e6d6>] ret_from_intr+0x0/0x20 [ 83.309351] [<ffffffff815f5105>] cpuidle_enter_state+0x105/0x330 [ 83.309353] [<ffffffff815f5367>] cpuidle_enter+0x17/0x20 [ 83.309356] [<ffffffff810dbe1a>] call_cpuidle+0x2a/0x50 [ 83.309358] [<ffffffff810dc1dd>] cpu_startup_entry+0x26d/0x3a0 [ 83.309360] [<ffffffff817701da>] rest_init+0x13a/0x140 [ 83.309363] [<ffffffff81f2af8e>] start_kernel+0x475/0x482 [ 83.309365] [<ffffffff81f2a315>] x86_64_start_reservations+0x2a/0x2c [ 83.309367] [<ffffffff81f2a452>] x86_64_start_kernel+0x13b/0x14a Fixes: 82d35437 ("drm/i915/skl: Implementation of SKL DPLL programming") Signed-off-by: Lyude <cpaul@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1454428183-994-1-git-send-email-cpaul@redhat.com (cherry picked from commit 78385cb3) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 09 Feb, 2016 2 commits
-
-
Lyude authored
Assuming any connector that isn't DP, MST, or HDMI is eDP definitely seems likely to cover up other bugs in the future. Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1454423709-21882-2-git-send-email-cpaul@redhat.com
-
Lyude authored
We don't actually check for INTEL_OUTPUT_DP_MST at all in here, as a result we skip assigning a DPLL to any DP MST ports, which makes link training fail: [ 1442.933896] [drm:intel_power_well_enable] enabling DDI D power well [ 1442.933905] [drm:skl_set_power_well] Enabling DDI D power well [ 1442.933957] [drm:intel_mst_pre_enable_dp] 0 [ 1442.935474] [drm:intel_dp_set_signal_levels] Using signal levels 00000000 [ 1442.935477] [drm:intel_dp_set_signal_levels] Using vswing level 0 [ 1442.935480] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 0 [ 1442.936190] [drm:intel_dp_set_signal_levels] Using signal levels 05000000 [ 1442.936193] [drm:intel_dp_set_signal_levels] Using vswing level 1 [ 1442.936195] [drm:intel_dp_set_signal_levels] Using pre-emphasis level 1 [ 1442.936858] [drm:intel_dp_set_signal_levels] Using signal levels 08000000 [ 1442.936862] [drm:intel_dp_set_signal_levels] Using vswing level 2 … [ 1442.998253] [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* too many full retries, give up [ 1442.998512] [drm:intel_dp_start_link_train [i915]] *ERROR* failed to train DP, aborting After which the pipe state goes completely out of sync: [ 70.075596] [drm:check_crtc_state] [CRTC:25] [ 70.075696] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in ddi_pll_sel (expected 0x00000000, found 0x00000001) [ 70.075747] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in shared_dpll (expected -1, found 0) [ 70.075798] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000021) [ 70.075840] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x80400173) [ 70.075884] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr2 (expected 0x00000000, found 0x000003a5) [ 70.075954] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 262750, found 72256) [ 70.075999] [drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 540000, found 148500) And if you're especially lucky, it keeps going downhill: [ 83.309256] Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler [ 83.309265] [ 83.309265] ================================= [ 83.309266] [ INFO: inconsistent lock state ] [ 83.309267] 4.5.0-rc1Lyude-Test #265 Not tainted [ 83.309267] --------------------------------- [ 83.309268] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. [ 83.309270] Xorg/1194 [HC0[1]:SC0[0]:HE1:SE1] takes: [ 83.309293] (&(&dev_priv->uncore.lock)->rlock){?.-...}, at: [<ffffffffa02a6073>] gen9_write32+0x63/0x400 [i915] [ 83.309293] {IN-HARDIRQ-W} state was registered at: [ 83.309297] [<ffffffff810e84f4>] __lock_acquire+0x9c4/0x1d00 [ 83.309299] [<ffffffff810ea1be>] lock_acquire+0xce/0x1c0 [ 83.309302] [<ffffffff8177d936>] _raw_spin_lock_irqsave+0x56/0x90 [ 83.309321] [<ffffffffa02a5492>] gen9_read32+0x52/0x3d0 [i915] [ 83.309332] [<ffffffffa024beea>] gen8_irq_handler+0x27a/0x6a0 [i915] [ 83.309337] [<ffffffff810fdbc1>] handle_irq_event_percpu+0x41/0x300 [ 83.309339] [<ffffffff810fdeb9>] handle_irq_event+0x39/0x60 [ 83.309341] [<ffffffff811010b4>] handle_edge_irq+0x74/0x130 [ 83.309344] [<ffffffff81009073>] handle_irq+0x73/0x120 [ 83.309346] [<ffffffff817805f1>] do_IRQ+0x61/0x120 [ 83.309348] [<ffffffff8177e6d6>] ret_from_intr+0x0/0x20 [ 83.309351] [<ffffffff815f5105>] cpuidle_enter_state+0x105/0x330 [ 83.309353] [<ffffffff815f5367>] cpuidle_enter+0x17/0x20 [ 83.309356] [<ffffffff810dbe1a>] call_cpuidle+0x2a/0x50 [ 83.309358] [<ffffffff810dc1dd>] cpu_startup_entry+0x26d/0x3a0 [ 83.309360] [<ffffffff817701da>] rest_init+0x13a/0x140 [ 83.309363] [<ffffffff81f2af8e>] start_kernel+0x475/0x482 [ 83.309365] [<ffffffff81f2a315>] x86_64_start_reservations+0x2a/0x2c [ 83.309367] [<ffffffff81f2a452>] x86_64_start_kernel+0x13b/0x14a Fixes: 82d35437 ("drm/i915/skl: Implementation of SKL DPLL programming") Signed-off-by: Lyude <cpaul@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1454428183-994-1-git-send-email-cpaul@redhat.com
-
- 03 Feb, 2016 1 commit
-
-
Matt Roper authored
In commit bfb9faab8 we added a workaround for some BXT BIOS that fail to properly initialize the DDI_A_4_LANES bit of the control register (4 lanes is the only valid configuration on BXT since there is no DDI E to share with). A recent patch added some additional checks on this register bit before the workaround gets applied; this breaks eDP on BXT in some settings. Some minor code shuffling is all we need to restore the workaround. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: 7cd87cb80 ("drm/i915: Check max number of lanes when registering DDI ports") Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1454022577-834-1-git-send-email-matthew.d.roper@intel.comReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
-
- 12 Jan, 2016 8 commits
-
-
Ville Syrjälä authored
commit 10afa0b6 ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL") added sanity checks to make sure we don't end up with too many ddi translation values for eDP ports, but it actually failed to check if the port is eDP. We still look up the edp translations for non-eDP ports, but don't use them, so we shouldn't be complaining about them either. Fixes: 10afa0b6 ("drm/i915: Reject >9 ddi translation entried if port != A/E on SKL") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452612496-9201-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
Move the ddi buffer translation programming to occur from the encoder .pre_enable() hook, for just the ddi port we are enabling. Previously we used to reprogram the translations for all ddi ports during init and during power well enabling. v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel) Resolve conflicts due to dev_priv->atomic_cdclk_freq Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
Only DDI A and E support 10 translation entries in DP mode. For the other ports the tenth entry is reserved for HDMI. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1449597590-6971-9-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
Make the ddi buffer programming code a bit more neat by passing around dev_priv instead of dev. v2: Resolve conflicts due to KBL Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
-
Ville Syrjälä authored
skl_get_buf_trans_edp() effectively contains another copy of skl_get_buf_trans_dp(). Remove the duplication and just call skl_get_buf_trans_dp() from skl_get_buf_trans_edp(). v2: Resolve conflicts due to KBL Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
-
Ville Syrjälä authored
skl_get_buf_trans_*() don't need the 'ddi_translations' local variable since all they with is assign and return. Just return the right thing directly and get rid of the local variable. v2: Resolve conflicts due to KBL Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
-
Ville Syrjälä authored
Rather than having open coded checks for the DDI A/E configuration, just store the max supported lane count in intel_digital_port. We had an open coded check for DDI A, but not for DDI E. So we may have been vilating the DDI E max lane count. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
DDI A and E share some of the lanes, so check that we have enough lanes for the purpose we need before registering the encoders. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1449597590-6971-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
- 07 Jan, 2016 3 commits
-
-
Rodrigo Vivi authored
No functional changes. That state the obvious and just duplicate the place we need to change whenever the table is updated. So let's clean it. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452021535-22641-1-git-send-email-rodrigo.vivi@intel.com
-
Rodrigo Vivi authored
When reviewing DDI translation table I noticed few changes we haven't incorporated yet and it is always good to follow latest spec. Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452009511-15064-1-git-send-email-rodrigo.vivi@intel.com
-
Rodrigo Vivi authored
When debuging an intermittent corrupted screen I suspected on DDI translation table and checked we are out of date with the spec. I'm not sure this will fix my bug yet, but it is always good to follow the spec. v2: Ville caught a switched i-boost value. Thanks! Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1452021087-21673-1-git-send-email-rodrigo.vivi@intel.com
-
- 11 Dec, 2015 1 commit
-
-
Ville Syrjälä authored
Done with coccinelle for the most part. However, it thinks '...' is part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder in its place and got rid of it with sed afterwards. @@ identifier dev, encoder, funcs; @@ int drm_encoder_init(struct drm_device *dev, struct drm_encoder *encoder, const struct drm_encoder_funcs *funcs, int encoder_type + ,const char *name, int DOTDOTDOT ) { ... } @@ identifier dev, encoder, funcs; @@ int drm_encoder_init(struct drm_device *dev, struct drm_encoder *encoder, const struct drm_encoder_funcs *funcs, int encoder_type + ,const char *name, int DOTDOTDOT ); @@ expression E1, E2, E3, E4; @@ drm_encoder_init(E1, E2, E3, E4 + ,NULL ) v2: Add ', or NULL...' to @name kernel doc (Jani) Annotate the function with __printf() attribute (Jani) Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
-
- 10 Dec, 2015 2 commits
-
-
Takashi Iwai authored
This patch adds a reverse mapping from a digital port number to intel_encoder object containing the corresponding intel_digital_port. It simplifies the query of the encoder a lot. Note that, even if it's a valid digital port, the dig_port_map[] might point still to NULL -- usually it implies a DP MST port. Due to this fact, the NULL check in each place has no WARN_ON() and just skips the port. Once when the situation changes in future, we might introduce WARN_ON() for a more strict check. Signed-off-by: Takashi Iwai <tiwai@suse.de>
-
Libin Yang authored
This patch adds support for DP MST audio in i915. Enable audio codec when DP MST is enabled if has_audio flag is set. Disable audio codec when DP MST is disabled if has_audio flag is set. Another separated patches to support DP MST audio will be implemented in audio driver. Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Libin Yang <libin.yang@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
-
- 09 Dec, 2015 1 commit
-
-
Rodrigo Vivi authored
Let's introduce ULT and ULX Kabylake definitions and start using it for a propper DDI buffer translation. v2: Remove extra white space. (Paulo) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
-
- 08 Dec, 2015 1 commit
-
-
Ville Syrjälä authored
Currently we disable some parts of FDI setup after a failed link training. But despite that we continue with the modeset as if everything is fine. This results in tons of noise from the state checker, and it means we're not following the proper modeset sequence for the rest of crtc enabling, nor for crtc disabling. Ideally we should abort the modeset and follow the proper disable sequence to shut off everything we enabled so far, but that would require a big rework of the modeset code. So instead just leave FDI up and running in its untrained state, and log an error. This is what we do on older platforms too. v2: Fix a typo in the commit message Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1449260570-14670-1-git-send-email-ville.syrjala@linux.intel.com
-
- 01 Dec, 2015 1 commit
-
-
Ville Syrjälä authored
The .get_config() hooks should not reference anything in crtc->config, everything should be based on the passed in pipe_config instead. So don't dig out the cpu_transcoder from crtc->config on ddi platfforms, and also avoid using the encoder->crtc link and instead look up the pipe via pipe_config->base.crtc. I don't think this will actually fix anything since during the initial state readout we set up the encoder->crtc link prior to calling .get_config(), and during the modeset state check the encoder->crtc ought to be correct anyway since it's that state we just programmed. But this seems the right thing to do anyway. While at it, do some house cleaning on the local variables in the .infoframe_enabled() hooks. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-
- 18 Nov, 2015 2 commits
-
-
Ville Syrjälä authored
Make I915_READ and I915_WRITE more type safe by wrapping the register offset in a struct. This should eliminate most of the fumbles we've had with misplaced parens. This only takes care of normal mmio registers. We could extend the idea to other register types and define each with its own struct. That way you wouldn't be able to accidentally pass the wrong thing to a specific register access function. The gpio_reg setup is probably the ugliest thing left. But I figure I'd just leave it for now, and wait for some divine inspiration to strike before making it nice. As for the generated code, it's actually a bit better sometimes. Eg. looking at i915_irq_handler(), we can see the following change: lea 0x70024(%rdx,%rax,1),%r9d mov $0x1,%edx - movslq %r9d,%r9 - mov %r9,%rsi - mov %r9,-0x58(%rbp) - callq *0xd8(%rbx) + mov %r9d,%esi + mov %r9d,-0x48(%rbp) callq *0xd8(%rbx) So previously gcc thought the register offset might be signed and decided to sign extend it, just in case. The rest appears to be mostly just minor shuffling of instructions. v2: i915_mmio_reg_{offset,equal,valid}() helpers added s/_REG/_MMIO/ in the register defines mo more switch statements left to worry about ring_emit stuff got sorted in a prep patch cmd parser, lrc context and w/a batch buildup also in prep patch vgpu stuff cleaned up and moved to a prep patch all other unrelated changes split out v3: Rebased due to BXT DSI/BLC, MOCS, etc. v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
-
Maarten Lankhorst authored
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum. Right now this is not handled well in i915, and it calculates the crtc needs to be reprogrammed on the first modeset without SSC, but the SPLL itself was kept active. Fix this by exposing SPLL as a shared pll that will not be returned by intel_get_shared_dpll; you have to know it exists to use it. Changes since v1: - Create a separate dpll_hw_state.spll for spll, and use separate pll functions for spll. Tested-by: Emil Renner Berthing <kernel@esmil.dk> Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.comSigned-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 17 Nov, 2015 1 commit
-
-
Damien Lespiau authored
Before this patch, we used the intel_display_power_{get,put} functions to make sure the PW1 and Misc I/O power wells were enabled all the time while LCPLL was enabled. We called a get() at intel_ddi_pll_init() when we discovered that LCPLL was enabled, then we would call put/get at skl_{un,}init_cdclk(). The problem is that skl_uninit_cdclk() is indirectly called by intel_runtime_suspend(). So it will only release its power well _after_ we already decided to runtime suspend. But since we only decide to runtime suspend after all power wells and refcounts are released, that basically means we will never decide to runtime suspend. So what this patch does to fix that problem is move the PW1 + Misc I/O power well handling out of the runtime PM mechanism: instead of calling intel_display_power_{get_put} - functions that touch the refcount -, we'll call the low level intel_power_well_{en,dis}able, which don't change the refcount. This way, it is now possible for the refcount to actually reach zero, and we'll now start runtime suspending/resuming. v2 (from Paulo): - Write a commit message since the original patch left it empty. - Rebase after the intel_power_well_{en,dis}able rename. - Use lookup_power_well() instead of hardcoded indexes. Testcase: igt/pm_rpm/rte (and every other rpm test) Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605Signed-off-by: Imre Deak <imre.deak@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
-
- 13 Nov, 2015 2 commits
-
-
jim.bride@linux.intel.com authored
While comparing the B-Spec with the code I noticed that several values in these tables have been updated in the spec, so I changed the code to match.. Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Link: http://patchwork.freedesktop.org/patch/msgid/1446852654-883-1-git-send-email-jim.bride@linux.intel.com
-
Ander Conselvan de Oliveira authored
The i_boost level in the DDI translation tables are stored per level. However, skl_ddi_set_iboos() would choose an entry of that table based on the port argument. Cc: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Jim Bride <jim.bride@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1447247754-802-1-git-send-email-ander.conselvan.de.oliveira@intel.com
-
- 10 Nov, 2015 1 commit
-
-
Ville Syrjälä authored
Set up the DDI->PLL mapping on SKL also for MST links. Might help make MST operational on SKL. v2: Rebased due to KBL Improve the patch subject, Jesse provided the new one Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1439826380-18403-1-git-send-email-ville.syrjala@linux.intel.com References: https://bugs.freedesktop.org/show_bug.cgi?id=91791Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-
- 09 Nov, 2015 1 commit
-
-
Matt Roper authored
The bspec indicates that DDI A using four lanes is the only valid configuration for Broxton (Broxton doesn't have a DDI E to split these lanes with); the DDI_A_4_LANES bit of port A's DDI_BUF_CTL should always be set by the BIOS. However some BIOS versions seem to only be setting this bit if eDP is actually lit up at boot time; if the BIOS doesn't turn on the eDP panel because an external display is plugged in, then this bit is never properly initialized. The end result of this is that we wind up calculating a lower max data rate than we should and may wind up rejecting the native mode for panels that we should be able to drive. Let's workaround this BIOS bug by just turning the DDI_A_4_LANES bit on in our driver's internal state if we recognize that we're running on BXT where it should have been on anyway. Cc: Imre Deak <imre.deak@intel.com> Cc: Bob Paauwe <bob.j.paauwe@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com> Tested-by: Bob Paauwe <bob.j.paauwe@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1446764012-27251-1-git-send-email-matthew.d.roper@intel.com
-
- 05 Nov, 2015 1 commit
-
-
Ander Conselvan de Oliveira authored
In order to prepare for a link training with DDI, the state machine would call intel_ddi_prepare_link_retrain(). To remove the dependency to the hardware information, replace that direct call with a callback. Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
-
- 28 Oct, 2015 1 commit
-
-
Rodrigo Vivi authored
Kabylake is a Intel
Processor containing Intel HD Graphics following Skylake. It is Gen9p5, so it inherits everything from Skylake. Let's start by adding the platform separated from Skylake but reusing most of all features, functions etc. Later we rebase the PCI-ID patch without is_skylake=1 so we don't replace what original Author did there. Few IS_SKYLAKEs if statements are not being covered by this patch on purpose: - Workarounds: Kabylake is derivated from Skylake H0 so no W/As apply here. - GuC: A following patch removes Kabylake support with an explanation: No firmware available yet. - DMC/CSR: Done in a separated patch since we need to be carefull and load the version for revision 7 since Kabylake is Skylake H0. v2: relative cleaner commit message and added the missed IS_KABYLAKE to intel_i2c.c as pointed out by Jani. Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-
- 26 Oct, 2015 1 commit
-
-
Ville Syrjälä authored
v2: Rebase due to SKL_DPLLx usage Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1442595836-23981-21-git-send-email-ville.syrjala@linux.intel.comReviewed-by: Jani Nikula <jani.nikula@intel.com>
-
- 21 Oct, 2015 3 commits
-
-
Jani Nikula authored
Revision checks are almost always accompanied by a platform check. (The exceptions are platform specific code.) Add helpers to check for a platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In most places this simplifies and clarifies the code. It will be obvious that revid macros are used for the correct platform. This should make it easier to find all the revision checks for workarounds for each platform, and make it easier to remove them once we drop support for early hardware revisions. This should also make it easier to differentiate between Skylake and Kabylake revision checks when Kabylake support is added. v2: rebase Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com
-
Jani Nikula authored
Prefer inclusive ranges for revision checks rather than "below B0". Per specs A2 is not used, so revid <= A1 matches revid < B0. Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-2-git-send-email-jani.nikula@intel.comSigned-off-by: Jani Nikula <jani.nikula@intel.com>
-
Shobhit Kumar authored
Especially in cases where pre-os does not enable display, cdclk might not be in sane state. During sanitization initialize cdclk with maximum value till we get dynamic cdclk support. v2: Check if BIOS programmed correctly rather than always calling init - Do validation of programmed cdctl and what it is expected - Only do slk_init_cdclk if validation failed else reuse BIOS programmed value v3: Move the validation logic in a separate sanitize function (Ville) v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead of hardcoded value (Ville) Cc: Imre Deak <imre.deak@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.comReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-