Add support for EON en25s64 SPI flash.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Use the new 'nor-jedec' binding to provide automatic detection of flash
that use the 0x9F READ ID opcode. This can help for use cases where
platforms just specify compatibility with "m25p80", and then see
messages like this:

  m25p80 spi32766.0: found s25fl256s1, expected m25p80

Instead, they can just specify the generic string and see this:

  m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)

Also, update the language about m25p_ids[] to straighten out the
expectations here. We should no longer need to continuously grow the
m25p_ids[] table, and in fact, we might want to start removing entries
which are not used in device trees so far, so we can just default to
auto-detection as much as possible in the future.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>

Almost all flash that are "compatible" with m25p80 support the JEDEC
READ ID opcode (0x9F), and in fact, that is often the only thing that is
used to differentiate them. Let's add a compatible string that
represents this lowest common denominator of compatibility.

Device trees can still specify manufacturer/device names in addition,
but (until some reason is found to differentiate between them through
device tree) software will likely want to bind just against the generic
name, and avoid unnecessarily growing its device ID binding tables.

This is related to the work of commit a5b7616c ("mtd:
m25p80,spi-nor: Fix module aliases for m25p80"), which showed that
maintaining these device tables as stable device-tree/modalias binding
tables is not a worthwhile burden for mostly-comptatible flash.

At the same time, let's update the binding doc to point to the
m25p_ids[] ID list instead of spi_nor_ids[]. The former can be used for
device tree bindings, but the latter cannot. In the future, we should
pare down the m25p_ids[] list to only those IDs which are actually used
in device trees.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>

I always go nuts when I start an MTD test on a slow device and have to
wait forever until it finishes. From the debug output I already know
what the issue is but I have to wait or reset the board hard. Resetting
is often not an option (remote access, you don't want lose the current
state, etc...).

The solution is easy, check for pending signals at key positions in the
code. Using that one can even stop a test by pressing CTRL-C as
insmod/modprobe have SIGINT pending.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In test case 3, we set vary_offset to write at different
offsets and lengths in the OOB available area. We need to
do the bitflip_limit check while checking for 0xff outside the
OOB offset + length area that we didn't modify during write.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Brian: whitespace fixup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The .remove callback may be used when detaching a device via sysfs, so
we can't expect to free up this memory.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>

This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var) which helps readability
and also handles all corner-cases properly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

if atmel,pmecc-lookup-table-offset is not found in DT node, we don't
need to map the ROM table as we will build a runtime gf table anyway.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

It's better to use a macro instead of just a number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch makes MTD dynamic partitioning more flexible by removing
overlap checks for dynamic partitions. I don't see any  particular
reason why overlapping dynamic partitions should be prohibited while
static partitions are allowed to overlap freely.

The checks previously had an off-by-one error, where 'end' should be
one less than what it is currently set at, and adding partitions out of
increasing order will fail. Disabling the checks resolves this issue.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch makes a sysfs variable called 'offset' on each partition
which contains the offset in bytes from the beginning of the master
device that the partition starts.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

For many use cases, it helps to have a device node for the entire
MTD device as well as device nodes for the individual partitions.
For example, this allows querying the entire device's properties.
A common idiom is to create an additional partition which spans
over the whole device.

This patch makes a config option, CONFIG_MTD_PARTITIONED_MASTER,
which makes the master partition present even when the device is
partitioned. This isn't turned on by default since it presents
a backwards-incompatible device numbering.

The patch also makes the parent of a partition device be the master,
if the config flag is set, now that the master is a full device.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch fixes a spelling typo in MODULE_DESCRIPTION in
ts5500_flash.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
[ Brian: fixed grammar in a spelling patch :) ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The Denali Controller IP does not support sub-page writes.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.

The variable used for handling the return of wait_for_cmpletion_timeout
was int but should be unsigned long, where it was not in use for
anything else and the return value in case of completion (>0) is not
used it was removed and wait_for_completion_timeout() used directly in
the if condition.

To make the timeout values a bit simpler to read and also handle all of
the corner cases correctly the declarations are moved to
msecs_to_jiffies().

The timeout declaration cleanup is just for readability
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In case of scan_bbt() failure, we should better propagate it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

When displaying dev_err() messages it is useful to print the error value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
[Brian: fix up "can not" at the same time]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

These lines were all indented one tab more than they should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor

arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"

It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Without this patch the timings are all set to 0 if not specified in the dts.
With this patch the driver falls back to use the defaults that are already
present in the driver and are known to work okay for some (older) boards.

Tested on a custom SPEAr600 based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We know "rc" is set so there is no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If a NAND device is not really present or pin muxes are not correctly
configured we can lock up the kernel waiting infinitely for NAND_STATUS
to be ready.

This can be easily reproduced on TI's DRA7-evm board by booting it
without NAND support in u-boot and disabling NAND pin muxes in the kernel.

Add timeout when waiting for NAND_CMD_RESET completion. As per ONFi v4.0
tRST can be upto 250ms for EZ-NAND and 5ms for raw NAND.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Flash lock/unlock is a flash-specific operations. Factor out a callback
for it to more readily support other vendors.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: VIET NGA DAO <vndao@altera.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>

As the only comments I got for the "mtd: cfi: reduce stack size"
patch were about whitespace changes, it appears necessary to fix
up the rest of the file as well, which contains the exact same
mistakes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The cfi_staa_write_buffers function uses a large amount of kernel stack
whenever CONFIG_MTD_MAP_BANK_WIDTH_32 is set, and that results in a
warning on ARM allmodconfig builds:

drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_write_buffers':
drivers/mtd/chips/cfi_cmdset_0020.c:651:1: warning: the frame size of 1208 bytes is larger than 1024 bytes [-Wframe-larger-than=]

It turns out that this is largely a result of a suboptimal implementation
of map_word_andequal(). Replacing this function with a straightforward
one reduces the stack size in this function by exactly 200 bytes,
shrinks the .text segment for this file from 27648 bytes to 26608 bytes,
and makes the warning go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We're not initializing the ooblen field. Our users don't care, since
they check that oobbuf == NULL first, but it's good practice to zero
unused fields out.

We can drop the NULL initializations since we're memset()ing the whole
thing.

Noticed by Coverity, CID #200821, #200822
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The only exit (break) from the preceding loop is nested within a
condition which yields req == NULL. This code is dead.

Coverity CID #752669
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

TclsRising is always 1.

Caught by Coverity.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>

Coverity noticed that these 'ret' assignments weren't being used. Let's
use them.

Note that nand_lock() and nand_unlock() are still not officially used by
any drivers.

Coverity CIDs #1227054 and #1227037
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Caught by Coverity (CID #200625 and others)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>

'ret' is always zero, so this is all dead code.

This should quiet Coverity CID #1226739.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

If no devices were found, we would already have skipped over this code.

Detected by Coverity, CID #744270
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>

The PARAM command was long unimplemented and it probably wasn't
noticed because chip probing using only the few bytes returned by the
READID command are good enough in most cases to determine the chip in
use.

Still to notice such a shortcoming earlier in the future would be nice
in case it's something more vital.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The mxc-nand driver never supported the PARAM command to read out the
ONFI parameter page and so always relied on probing my manufacturer and
device id (as provided by the READID command).

This patch implements reading out the first parameter page copy at least
which should be good enough in practise.

This makes the boot log change from

	nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
	nand: Micron NAND 128MiB 1,8V 16-bit

to
	nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
	nand: Micron MT29F1G16ABBDAH4

on my machine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The mxc-nand controller works pagewise and so usually only sends
commands to the flash chip with column == 0. A request with column != 0
from the upper layer is then fulfilled by indexing appropriately into the
device's RAM buffer.

To be able to access the ONFI marker at offset 0x20 in reply to the
READID command however it's invalid to read 32 bytes starting from
column 0.

So let the function used to send the address cycles send the column
address actually passed instead of 0 and fix all callers to pass 0
instead appropriately. Also add some warnings in case this patch changes
the drivers semantics.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>