Restructure the eswitch ingress acl codes into eswitch directory
and different files:
. Acl ingress helper functions to acl_helper.c/h
. Acl ingress functions used in offloads mode to acl_ingress_ofld.c
. Acl ingress functions used in legacy mode to acl_ingress_lgy.c

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>

Refactor the egress acl codes so that offloads and legacy modes
can configure specifically their own needs of egress acl table,
groups and rules. While at it, restructure the eswitch egress
acl codes into eswitch directory and different files:
. Acl egress helper functions to acl_helper.c/h
. Acl egress functions used in offloads mode to acl_egress_ofld.c
. Acl egress functions used in legacy mode to acl_egress_lgy.c

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.

Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Raw PHY TDR data

Some ethernet PHYs allow access to raw TDR data in addition to summary
diagnostics information. Add support for retrieving this data via
netlink ethtool. The basic structure in the core is the same as for
normal phy diagnostics, the PHY driver simply uses different helpers
to fill the netlink message with different data.

There is a graphical tool under development, as well a ethtool(1)
which can dump the data as text and JSON.

A patched ethtool(1) can be found in
https://github.com/lunn/ethtool.git feature/cable-test-v5

Thanks for Chris Healy for lots of testing.

v2:
See the individual patches but:

Pass distances in centimeters, not meters

Allow the PHY to round distances to what it supports and report what
it actually used along with the results.

Make the Marvell PHY use steps a multiple of 0.805 meters, its native
step size.

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Unsquash the last two patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.

If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet PHYs can return the raw time domain reflectromatry data.
Add the attributes to allow this data to be requested and returned via
netlink ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2:
m -> cm
Report what the PHY actually used for start/stop/step.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ignore loopback-originatig packets soon enough and don't try to process L2
header where it doesn't exist. The very similar br_handle_frame() in bridge
code performs exactly the same check.

This is an example of such ICMPv6 packet:

skb len=96 headroom=40 headlen=96 tailroom=56
mac=(40,0) net=(40,40) trans=80
shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
csum(0xae2e9a2f ip_summed=1 complete_sw=0 valid=0 level=0)
hash(0xc97ebd88 sw=1 l4=1) proto=0x86dd pkttype=5 iif=24
dev name=etha01.212 feat=0x0x0000000040005000
skb headroom: 00000000: 00 7c 86 52 84 88 ff ff 00 00 00 00 00 00 08 00
skb headroom: 00000010: 45 00 00 9e 5d 5c 40 00 40 11 33 33 00 00 00 01
skb headroom: 00000020: 02 40 43 80 00 00 86 dd
skb linear:   00000000: 60 09 88 bd 00 38 3a ff fe 80 00 00 00 00 00 00
skb linear:   00000010: 00 40 43 ff fe 80 00 00 ff 02 00 00 00 00 00 00
skb linear:   00000020: 00 00 00 00 00 00 00 01 86 00 61 00 40 00 00 2d
skb linear:   00000030: 00 00 00 00 00 00 00 00 03 04 40 e0 00 00 01 2c
skb linear:   00000040: 00 00 00 78 00 00 00 00 fd 5f 42 68 23 87 a8 81
skb linear:   00000050: 00 00 00 00 00 00 00 00 01 01 02 40 43 80 00 00
skb tailroom: 00000000: ...
skb tailroom: 00000010: ...
skb tailroom: 00000020: ...
skb tailroom: 00000030: ...

Call Trace, how it happens exactly:
 ...
 macvlan_handle_frame+0x321/0x425 [macvlan]
 ? macvlan_forward_source+0x110/0x110 [macvlan]
 __netif_receive_skb_core+0x545/0xda0
 ? enqueue_task_fair+0xe5/0x8e0
 ? __netif_receive_skb_one_core+0x36/0x70
 __netif_receive_skb_one_core+0x36/0x70
 process_backlog+0x97/0x140
 net_rx_action+0x1eb/0x350
 ? __hrtimer_run_queues+0x136/0x2e0
 __do_softirq+0xe3/0x383
 do_softirq_own_stack+0x2a/0x40
 </IRQ>
 do_softirq.part.4+0x4e/0x50
 netif_rx_ni+0x60/0xd0
 dev_loopback_xmit+0x83/0xf0
 ip6_finish_output2+0x575/0x590 [ipv6]
 ? ip6_cork_release.isra.1+0x64/0x90 [ipv6]
 ? __ip6_make_skb+0x38d/0x680 [ipv6]
 ? ip6_output+0x6c/0x140 [ipv6]
 ip6_output+0x6c/0x140 [ipv6]
 ip6_send_skb+0x1e/0x60 [ipv6]
 rawv6_sendmsg+0xc4b/0xe10 [ipv6]
 ? proc_put_long+0xd0/0xd0
 ? rw_copy_check_uvector+0x4e/0x110
 ? sock_sendmsg+0x36/0x40
 sock_sendmsg+0x36/0x40
 ___sys_sendmsg+0x2b6/0x2d0
 ? proc_dointvec+0x23/0x30
 ? addrconf_sysctl_forward+0x8d/0x250 [ipv6]
 ? dev_forward_change+0x130/0x130 [ipv6]
 ? _raw_spin_unlock+0x12/0x30
 ? proc_sys_call_handler.isra.14+0x9f/0x110
 ? __call_rcu+0x213/0x510
 ? get_max_files+0x10/0x10
 ? trace_hardirqs_on+0x2c/0xe0
 ? __sys_sendmsg+0x63/0xa0
 __sys_sendmsg+0x63/0xa0
 do_syscall_64+0x6c/0x1e0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various trap changes - part 2

This patch set contains another set of small changes in mlxsw trap
configuration. It is the last set before exposing control traps (e.g.,
IGMP query, ARP request) via devlink-trap.

Tested with existing devlink-trap selftests. Please see individual
patches for a detailed changelog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.

However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.

To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).

This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.

Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.

As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.

Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch the split is no longer necessary and all the
trap groups can be moved under the same enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit e6125230 ("mlxsw: spectrum_trap: Introduce
dummy group with thin policer"), the purpose of the "thin" policer is to
pass as less packets as possible to the CPU.

The identifier of this policer is currently set according to the maximum
number of used trap groups, but this is fragile: On Spectrum-1 the
maximum number of policers is less than the maximum number of trap
groups, which might result in an invalid policer identifier in case the
number of used trap groups grows beyond the policer limit.

Solve this by dynamically allocating the policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.

In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.

These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Group these various IPv6 packets (e.g., router solicitations, router
advertisement) together and subject them to the same policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trap groups that use the same policer settings can share the same switch
case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets that are trapped via tc's trap action are currently subject to
the same policer as packets hitting local routes. The latter are
critical to the correct functioning of the control plane, while the
former are mainly used for traffic inspection.

Split the ACL trap to a separate group with its own policer. Use a
higher priority for these traps than for traps using mirror action
(e.g., ARP, IGMP). Otherwise, packets matching both traps will not be
forwarded in hardware (because of trap action) and also not forwarded in
software because they will be marked with 'offload_fwd_mark'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can try to coalesce skbs we take from the subflows rx queue with the
tail of the mptcp rx queue.

If successful, the skb head can be discarded early.

We can also free the skb extensions, we do not access them after this.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't call netif_napi_del() manually, free_netdev() does this for us.
In addition reorder calls to match reverse order of calls in probe().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fugang Duan says:

====================
net: ethernet: fec: move GPR register offset and bit into DT

The commit da722186 (net: fec: set GPR bit on suspend by
DT configuration) set the GPR reigster offset and bit in driver
for wol feature support.

It brings trouble to enable wol feature on imx6sx/imx6ul/imx7d
platforms that have multiple ethernet instances with different
GPR bit for stop mode control. So the patch set is to move GPR
register offset and bit define into DT, and enable imx6q/imx6dl
imx6qp/imx6sx/imx6ul/imx7d stop mode support.

Currently, below NXP i.MX boards support wol:
- imx6q/imx6dl/imx6qp sabresd
- imx6sx sabreauto
- imx7d sdb

imx6q/imx6dl/imx6qp sabresd board dts file miss the property
"fsl,magic-packet;", so patch#4 is to add the property for stop
mode support.

v1 -> v2:
 - driver: switch back to store the quirks bitmask in driver_data
 - dt-bindings: rename 'gpr' property string to 'fsl,stop-mode'
 - imx6/7 dtsi: add imx6sx/imx6ul/imx7d ethernet stop mode property
v2 -> v3:
 - driver: suggested by Sascha Hauer, use a struct fec_devinfo for
   abstracting differences between different hardware variants,
   it can give more freedom to describe the differences.
 - imx6/7 dtsi: correct one typo pointed out by Andrew.

Thanks Martin, Andrew and Sascha Hauer for the review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Update the imx6qdl gpr property to define gpr register
  offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- rename the 'gpr' property string to 'fsl,stop-mode'.
- Update the property to define gpr register offset and
bit in DT, since different instance have different gpr bit.

v2:
 * rename 'gpr' property string to 'fsl,stop-mode'.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit da722186 (net: fec: set GPR bit on suspend by DT
configuration) set the GPR reigster offset and bit in driver for
wake on lan feature.

But it introduces two issues here:
- one SOC has two instances, they have different bit
- different SOCs may have different offset and bit

So to support wake-on-lan feature on other i.MX platforms, it should
configure the GPR reigster offset and bit from DT.

So the patch is to improve the commit da722186 (net: fec: set GPR
bit on suspend by DT configuration) to support multiple ethernet
instances on i.MX series.

v2:
 * switch back to store the quirks bitmask in driver_data
v3:
 * suggested by Sascha Hauer, use a struct fec_devinfo for
   abstracting differences between different hardware variants,
   it can give more freedom to describe the differences.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Netlink policies are generally declared as const.
This is safer and prevents potential bugs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
One batch of changes, containing:
 * hwsim improvements from Jouni and myself, to be able to
   test more scenarios easily
 * some more HE (802.11ax) support
 * some initial S1G (sub 1 GHz) work for fractional MHz channels
 * some (action) frame registration updates to help DPP support
 * along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: phy: mscc-miim: reduce waiting time between MDIO transactions

This series aims at reducing the waiting time between MDIO transactions
when using the MSCC MIIM MDIO controller.

I'm not sure we need patch 4/4 and we could reasonably drop it from the
series. I'm including the patch as it could help to ensure the system
is functional with a non optimal configuration.

We needed to improve the driver's performances as when using a PHY
requiring lots of registers accesses (such as the VSC85xx family),
delays would add up and ended up to be quite large which would cause
issues such as: a slow initialization of the PHY, and issues when using
timestamping operations (this feature will be sent quite soon to the
mailing lists).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver uses a read polling mechanism to check the status of the MDIO
bus, to know if it is ready to accept next commands. This polling
mechanism uses usleep_delay() under the hood between reads which is fine
as long as high resolution timers are enabled. Otherwise the delays will
end up to be much longer than expected.

This patch fixes this by using udelay() under the hood when
CONFIG_HIGH_RES_TIMERS isn't enabled. This increases CPU usage.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MSCC MIIM MDIO driver uses a waiting logic to wait for the MDIO bus
to be ready to accept next commands. It does so by polling the BUSY
status bit which indicates the MDIO bus has completed all pending
operations. This can take time, and the controller supports writing the
next command as soon as there are no pending commands (which happens
while the MDIO bus is busy completing its current command).

This patch implements this improved logic by adding an helper to poll
the PENDING status bit, and by adjusting where we should wait for the
bus to not be busy or to not be pending.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>