- 04 Apr, 2017 22 commits
-
-
Daniel Vetter authored
Just drive-by, but we have gsoc running so better to update it now. Great news is that two entries can be removed because essentially all done. v2: Keep a bunch of the todos, Gabriel is working on them. Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Reviewed-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170404095304.17599-1-daniel.vetter@ffwll.ch
-
John Keeping authored
This reset is required in order to fully reset the internal state of the MIPI controller. Signed-off-by:
John Keeping <john@metanate.com> Reviewed-by:
Brian Norris <briannorris@chromium.org> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170303113945.3bd2cbd9.john@metanate.com
-
Neil Armstrong authored
This patch adds the dw-hdmi bindings and RST kerneldoc to maintained files. Acked-by:
-
Neil Armstrong authored
Acked-by:
-
Neil Armstrong authored
Acked-by:
-
Neil Armstrong authored
This binding describes the Amlogic Meson specific extension to the Synopsys Designware HDMI Controller. Acked-by:
-
Neil Armstrong authored
The Amlogic Meson GXBB/GXL/GXM SoCs embeds a Synopsys DesignWare HDMI TX Controller with a custom Bridge + PHY around the Controller. This driver makes uses of all the custom PHY plat data callbacks and enables the compatible HDMI modes to be configured as a drm_encoder instance. Acked-by:
-
Neil Armstrong authored
This patch adds support for the supported HDMI Venc modes and add the VPP mux value to switch to ENCP encoder. Acked-by:
-
Neil Armstrong authored
This patchs adds support for the supported HDMI modes clocks frequencies. Acked-by:
-
Neil Armstrong authored
Since this is managed now by the components code, if CVBS is not available and HDMI neither, the drm driver won't bind anyway. Acked-by:
-
Neil Armstrong authored
This patch adds support for optional components connected through the Device Tree endpoints scheme. Acked-by:
-
Neil Armstrong authored
Add missing VPU HDMI register. Acked-by:
-
Neil Armstrong authored
Clean the crtc_enable by using the proper crtc_state instead of the state of the primary plane state data. Also fix the dependency to commit the plane changes even if enable is called after the flush. Acked-by:
-
Neil Armstrong authored
The HDMI TX controller support HPD and RXSENSE signaling from the PHY via it's STAT0 PHY interface, but some vendor PHYs can manage these signals independently from the controller, thus these STAT0 handling should be moved to PHY specific operations and become optional. The existing STAT0 HPD and RXSENSE handling code is refactored into a supplementaty set of default PHY operations that are used automatically when the platform glue doesn't provide its own operations. Reviewed-by:
Jose Abreu <joabreu@synopsys.com> Reviewed-by:
Archit Taneja <architt@codeaurora.org> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Neil Armstrong authored
This patch adds a new DRM documentation entry and links to the input format table added in the dw_hdmi header. Reviewed-by:
-
Neil Armstrong authored
Switch code to use the newly introduced V4L bus formats IDs instead of custom defines. Also use the V4L encoding defines. Some display pipelines can only provide non-RBG input pixels to the HDMI TX Controller, this patch takes the pixel format from the plat_data if provided. Reviewed-by:
-
Laurent Pinchart authored
In preparation for adding PHY operations to handle RX SENSE and HPD, group all the PHY interrupt setup code in a single location and extract it to a separate function. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by:
-
Sean Paul authored
Merge tag 'topic/synopsys-media-formats-2017-04-03' of git://anongit.freedesktop.org/git/drm-misc into drm-misc-next Media formats for synopsys HDMI TX Controller Signed-off-by:
-
Sean Paul authored
Backmerging in order to pull vmwgfx [1] and the new synopsys media format [2] reqs. [1]- http://patchwork.freedesktop.org/patch/msgid/20170331233255.GA38850@syeh-m02 [2]- http://patchwork.freedesktop.org/patch/msgid/20170403163544.kcw5kk52tgku5xua@art_vandelaySigned-off-by:
-
Gerd Hoffmann authored
Lookup format using virtio_gpu_translate_format() instead of hardcoding it. Fixes xorg display on bigendian guests (i.e. ppc64). Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Dave Airlie <airlied@redhat.com> Acked-by:
Laurent Vivier <lvivier@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170403070845.10793-3-kraxel@redhat.com
-
Gerd Hoffmann authored
Factors out code, no functional change. Signed-off-by:
-
Neil Armstrong authored
Meson DRM is switching to drm-misc, so remove the freedesktop drm/meson-drm git repository from MAINTAINERS entry. Acked-by:
-
- 03 Apr, 2017 18 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linuxDave Airlie authored
omapdrm changes for 4.12 Main changes include: * Add support for render nodes. * Refactor omapdss code to allow multiple DISPC implementations. This is pre-work for DSS6 support. * Fix replication logic bug, which caused RGB565 fb to be shown too dark on a 24bit display. * Improve detection of display stack readiness, which should remove the probe order issues. * Link panel-dpi with its backlight, so that they are turned on/off in sync. * Fix possibly incorrect setup of sync and data-enable signals. * Get rid of DRM_OMAP_NUM_CRTCS config option. * tag 'omapdrm-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (34 commits) drm/omap: Major omap_modeset_init() cleanup drm/omap: Remove the obsolete #define omap_plane _omap_plane hack drm/omap: Fix one ugly indentation style break left by coccinelle drm/omap: Rename enum omap_plane to enum omap_plane_id drm/omap: Get rid of DRM_OMAP_NUM_CRTCS config option drm/omap: fix crash on module unload drm/omap: use drm_atomic_helper_shutdown() drm/omap: fix display SYNC/DE flags drm/omap: dispc: improve debug print of display flags drm/omap: displays: panel-dpi: Support for handling backlight devices drm/omap: poll only connectors where the connect/disconnect can be checked drm/omap: display: Add displays in sorted order to the panel_list drm/omap: Use omapdss_stack_is_ready() to check that the display stack is up drm/omap: dss: Support for detecting display stack readiness drm/omap: dss: Functions to check components in the display/output list drm/omap: fix replication logic drm/omap: remove unused dispc_wb_enable & dispc_wb_is_enabled drm/omap: remove all EXPORT_SYMBOLs from dispc.c drm/omap: use dispc_ops drm/omap: fill dispc_ops ...
-
Russell King authored
Align the heading with the values output from debugfs. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Sumit Semwal <sumit.semwal@linaro.org> Link: http://patchwork.freedesktop.org/patch/msgid/E1cttOq-0006GX-U7@rmk-PC.armlinux.org.uk
-
Neil Armstrong authored
Add documentation for added Bus Formats to describe RGB and YUV formats used as input to the Synopsys DesignWare HDMI TX Controller. Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Neil Armstrong authored
In order to describe the RGB and YUV bus formats used to feed the Synopsys DesignWare HDMI TX Controller, add missing formats to the list of Bus Formats. Documentation for these formats is added in a separate patch. Reviewed-by:
-
Jyri Sarha authored
Cleanup overly complex omap_modeset_init(). The function is trying to support many unusual configuration, that have never been tested and are not supported by other parts of the dirver. After cleanup the init function creates exactly one connector, encoder, crtc, and primary plane per each connected dss-device. Each connector->encoder->crtc chain is expected to be separate and each crtc is connect to a single dss-channel. If the configuration does not match the expectations or exceeds the available resources, the configuration is rejected. Signed-off-by:
Jyri Sarha <jsarha@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com>
-
Jyri Sarha authored
Remove the obsolete "#define omap_plane _omap_plane" hack and other related hacks to get around the enum omap_plane colliding with struct omap_plane. Signed-off-by:
-
Jyri Sarha authored
Fix one ugly indentation style break left by the previous coccilnelle patch. Signed-off-by:
-
Jyri Sarha authored
The enum omap_plane conflicted with the same struct name for omapdrm plane private data. This rename should solve the conflict. The rename was implement with this very simple coccinelle patch: ------------------------ @@ @@ enum -omap_plane +omap_plane_id ------------------------ The patch was applied like this: spatch --sp-file <cocci_file> --all-includes --in-place --dir drivers/gpu/drm/omapdrm The above patch did not rename the actual enum definition. That was added manually on top of the spatch changes. Signed-off-by:
-
Jyri Sarha authored
Allocate one CRTC for each connected output and get rid of DRM_OMAP_NUM_CRTCS config option. We still can not create more CRTCs than we have DSS display managers. We also reserve one overlay per CRTC for primary plane so we can not have more CRTCs than we have overlays either. Signed-off-by:
-
Tomi Valkeinen authored
When unloading omapdrm we get a NULL pointer deref in omap_drm_irq_uninstall(). This is caused by: 967dd484 ("drm: remove drm_vblank_no_hw_counter assignment from driver code") We shut down all the crtcs at unload time before calling omap_drm_irq_uninstall, so the code in omap_drm_irq_uninstall() is unnecessary and can be removed. Signed-off-by:
-
Tomi Valkeinen authored
Use drm_atomic_helper_shutdown() to ensure that all crtcs are disabled when unloading the driver. Signed-off-by: -
Tomi Valkeinen authored
At the moment VSYNC/HSYNC/DE high/low flags set by the panel/encoder drivers get lost when the videotimings are translated to DRM's videomode, as DRM's mode does not have corresponding flags. DRM has bus-flags for this purpose, and while it lacks a few flags at the moment, it should be used here. However, until we rewrite omapdrm's device model, using bus-flags is rather difficult. As a short term fix, this patch makes sure that every time the videomode is set in omap_crtc_mode_set_nofb(), the driver asks for the SYNC/DE flags from the panel/encoder drivers, and thus we get the correct flags into use. Signed-off-by: -
Tomi Valkeinen authored
Instead of printing 0/1 for display flags like vsync high/low, use a tri-state print (-1/0/1) to indicate the "undefined" state. Signed-off-by: -
Peter Ujfalusi authored
The associated backlight device can be configured via DT by providing the phandle to the device. If the backlight device is configured, the driver can manage the backligt along with the panel's power state, iow it can turn on the backlight when the panel is enabled and turn it off when the panel is disabled. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Peter Ujfalusi authored
When the connector associated detect callback is not provided, we can not detect if the display is connected or disconnected. These displays do not support hot plug, they are always connected. Let DRM know that connectors w/o detect callback should not be polled. Signed-off-by:
-
Peter Ujfalusi authored
Keep the panel_list ordered according to aliases. The DRM connectors will be created following the panel_list. By keeping the list ordered the DRM connectors will be created in the same order regardless of the driver probe order. Signed-off-by:
-
Peter Ujfalusi authored
Instead of 'guessing' based on aliases of the status of the DSS drivers, use the new interface to check that all needed drivers are loaded. In this way we can be sure that all needed drivers are loaded so it is safe to continue the probing of omapdrm. This method will allow the omapdrm to be probed 'headless', without outputs. Signed-off-by:
-
Peter Ujfalusi authored
When omapdss is loaded (all core components are in place) create a list of devices used in the display graph. This list later can be used by omapdrm via the omapdss_stack_is_ready() function to check that these components are loaded. Based on this information, omapdrm can defer probe in case when the omapdss stack is not ready yet. Signed-off-by:
-
