- 18 Apr, 2012 25 commits
-
-
Huang, Xiong authored
TPD producer/consumer index is 16bit wide. 16bit read/write reduce the dependency of the 2 tpd rings (hi and lo) rename reg(157C/1580) to keep name coninsistency. Signed-off-by:
xiong <xiong@qca.qualcomm.com> Tested-by:
Liu David <dwliu@qca.qualcomm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Huang, Xiong authored
l1c & later chips don't support DMA for SMB. CMB is removed from hardware. reg(15C8) is used to trig interrupt by tpd threshold. Signed-off-by:
-
Huang, Xiong authored
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to access external NV-memory. l1c & later chip doesn't use it any more. PHY 0/1 registers occupy the last 2 slots of the dump table. Signed-off-by:
-
Huang, Xiong authored
remove HDS register as it doesn't exist in hardware. Signed-off-by:
-
Huang, Xiong authored
the multiple-RX-Q in hardware doesn't work, all related register definition & code are removed. Signed-off-by:
-
Huang, Xiong authored
replace unavailable email of the author since he left with a mail-list. update company info as well, Atheros was acquired by Qualcomm. insert "100" to driver description since it support 100M controller. Signed-off-by:
-
John W. Linville authored
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-testmode.c include/net/nfc/nfc.h net/nfc/netlink.c net/wireless/nl80211.c
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Included changes: * remove duplicated line in comment * add htons() invocation for tt_crc as suggested by Al Viro * OriGinator Message seqno initial value is now random * some cleanups and fixes
-
Antonio Quartulli authored
When we receive an OGM from from a node for the first time, the last_real_seqno field of the orig_node structure has not been initialised yet. The value of this field is used to compute the current ogm-seqno window and therefore the protection mechanism will probably drop the packet due to an out-of-window error. To avoid this situation this patch adds a check to skip the window protection mechanism if no neighbour nodes have already been added. When the first neighbour node is added, the last_real_seqno field is initialised too. Reported-by:
Marek Lindner <lindner_marek@yahoo.de> Signed-off-by:
Antonio Quartulli <ordex@autistici.org>
-
Antonio Quartulli authored
OGM sequence numbers are declared as uint32_t and so they have to printed using %u instead of %d in order to avoid wrong representations. Signed-off-by: -
Antonio Quartulli authored
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the kernel macro ETH_HLEN. This patch substitute each occurrence of the former expressione with the latter one. Signed-off-by: -
Marek Lindner authored
The coming protocol changes also will have a part called "OGM". That makes it necessary to introduce a distinction in the code base. Signed-off-by:
-
Marek Lindner authored
Using BATMAN_OGM_LEN leaves one with the impression that this is the full packet size which is not the case. Therefore the variable is renamed. Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Antonio Quartulli authored
Remove an accidentally added duplicated line in a function comment Signed-off-by: -
Antonio Quartulli authored
Before sending out a TT_Request packet we must convert the tt_crc field value to network order (since it is 16bits long). Reported-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
-
majianpeng authored
Signed-off-by:
majianpeng <majianpeng@gmail.com> Signed-off-by:
-
majianpeng authored
Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Eric Dumazet authored
Signed-off-by:
-
françois romieu authored
The driver does not always use the same timing for what looks like the same operations. - DCR0 Use the same udelay everywhere for reset. Upper bound is 100 us. - DCR9 Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO clock range. Signed-off-by:
Francois Romieu <romieu@fr.zoreil.com> Reviewed-by:
Grant Grundler <grundler@parisc-linux.org> Signed-off-by:
-
- 17 Apr, 2012 15 commits
-
-
David S. Miller authored
Fix mixed space and tabs. Put bpf_jit_load_*[] externs into bpf_jit.h "while(0)" --> "while (0)" "COND (X)" --> "COND(X)" Document branch offset calculations, and bpf_error's return sequence. Document the reason we need to emit three nops between the %y register write and the divide instruction. Remove erroneous trailing semicolons from emit_read_y() and emit_write_y(). Based upon feedback from Sam Ravnborg. Signed-off-by: -
David S. Miller authored
Correct conventions comments. %o4 and %o5 were swapped, %g3 was not documented. Use r_TMP instead of r_SKB_DATA + r_OFF where possible in assembler stubs. Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s comments. Based upon feedback from Richard Mortimer. Signed-off-by: -
Amitkumar Karwar authored
We get two timing related fields for each bss from firmware in scan results. 1) timestamp - Actual timestamp information in probe response/beacon 2) network_tsf - firmware's TSF value at the time the beacon or probe response was received. Both are needed while associating by firmware. The patch takes care of following things. 1) We should pass "timestamp" to cfg80211_inform_bss(), but currently "network_tsf" is being provided. This error is corrected here. 2) Rename "network_tsf" to "fw_tsf" 3) Make use of u64 variable instead of an array of u8/u32 to save parsed "timestamp" information. 4) Use timestamp provided to stack in scan results using cfg80211_inform_bss() while associating. (bss->tsf) 5) Allocate space to save fw_tsf in "priv" of cfg80211_bss and retrieve it while associating. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Rearrange some code to save extra parameters to the functions. Signed-off-by:
-
Daniel Drake authored
Signed-off-by:
Daniel Drake <dsd@laptop.org> Acked-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Daniel Drake authored
Signed-off-by:
-
Daniel Drake authored
As described at http://article.gmane.org/gmane.linux.kernel.wireless.general/86084 libertas is taking a long time to load because it loads firmware during module loading. Add a new API for interface drivers to load their firmware asynchronously. The same semantics of the firmware table are followed like before. Interface drivers will be converted in follow-up patches, then we can remove the old, synchronous firmware loading function. Signed-off-by:
-
Daniel Drake authored
These simple sanity check avoids extra complexity in error paths when moving to asynchronous firmware loading (which means the device may fail to init some time after its creation). Signed-off-by:
-
Daniel Drake authored
Remove the ability to pass module parameters with firmware filenames for USB and SDIO interfaces. Remove the ability to pass custom "user" filenames to lbs_get_firmware(). Remove the ability to reprogram internal device memory with a different firmware from the USB driver (we don't know of any users), and simplify the OLPC firmware loading quirk to simply placing the OLPC firmware at the top of the list (we don't know of any users other than OLPC). Move lbs_get_firmware() into its own file. These simplifications should have no real-life effect but make the upcoming transition to asynchronous firmware loading considerably less painful. Signed-off-by:
-
Andreas Hartmann authored
There are connection stalls or very poor throughputs with rt2800 hardware using 802.11n in AP mode since patch "mac80211: retry sending failed BAR frames later instead of tearing down aggr"[1][2]. Since rt2800 hardware is not able to correctly report the tx status of BAR frames, this patch removes as workaround the existing error handling on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails. As a result, most wifi clients (aside from Intel STAs on Windows) instead will timeout now the reorder buffer and request the lost frame again. The correct solution would be, to tear down BA session on AP side. This patch was born on the basis of "[RFT] rt2x00: Tear down BA session on QoS frame failure"[3]. Thanks to Helmut Schaa for his support! [1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304 [2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98 [3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569Signed-off-by:
Andreas Hartmann <andihartmann@01019freenet.de> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Gabor Juhos authored
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function does the same thing. Remove the macro, and use the inline function instead. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Gabor Juhos authored
Both eeprom.c and ar9003_eeprom.c has an indentical 'ath9k_hw_fbin2freq' function. Move the function to a common place and remove the duplicates. Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
-
Gabor Juhos authored
The existing constants are used for reduction/increase tx power level on devices with 2x2 and 3x3 chainmask. Both reduction and increase must use the same value, so it makes no sense to use separate constants for them. Signed-off-by:
-
Julia Lawall authored
Add a corresponding leave call on error failure. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
-
