- 22 Aug, 2013 40 commits
-
-
Huang Shijie authored
The uart2 in the imx6q-arm2 board is used as a DTE uart, this patch adds the necessary DTE pads for uart2. Signed-off-by:
Huang Shijie <b32955@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Huang Shijie authored
In order to enable the DMA for some uart port in imx6sl, we add the "fsl,imx6q-uart" to the uart's compatible property. Signed-off-by:
-
Markus Pargmann authored
Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Signed-off-by:
-
Markus Pargmann authored
Both buses are not used on the phyCARD-S module. This patch moves them to the rdk file. Remove ioexpander. Signed-off-by:
-
Markus Pargmann authored
This sensor was introduced in the original pca100 board file, but phyCARD-S SOM and RDK do not have a temperature sensor. Signed-off-by:
-
Fabio Estevam authored
To make it consistent with the other i.mx SoCs, let's add the cpus nodes. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Wandboard has a sgtl5000 codec. Add audio support. Signed-off-by:
-
Markus Pargmann authored
Fixup of commit "ARM: dts: Add device tree support for phycard pca100". Remove wrong I2C RTC node. Signed-off-by:
-
Alexander Shiyan authored
Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Alexander Shiyan authored
This patch adds CAN (NXP SJA1000) node for Phytec PCM-970 RDK. Signed-off-by:
-
Alexander Shiyan authored
This patch adds SRAM node for Phytec PCM-038 module. Signed-off-by:
-
Alexander Shiyan authored
This patch adds WEIM node for Phytec PCM-038 module. Migrate existing on-module NOR-flash as children of WEIM CS0. Signed-off-by:
-
Alexander Shiyan authored
This patch adds the missing (Wireless External Interface Module) WEIM devicetree node for i.MX27 CPUs. Signed-off-by:
-
Alexander Shiyan authored
This patch moves IIM node under AIPI2 bus, since this is proper location for this module. Signed-off-by:
-
Huang Shijie authored
Add the #dma-cells property for all the sdma in all the imx platforms. Signed-off-by:
-
Philipp Zabel authored
i.MX6DL does not have the second IPU, but the LVDS multiplexers can connect either LVDS channel of the LDB to IPU1 DI0 or IPU1 DI1. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> [shawn.guo: remove "crtcs" property from imx6qdl.dtsi] Signed-off-by:
-
Fabio Estevam authored
Enable Video Processing Unit (VPU) support. Signed-off-by:
-
Philipp Zabel authored
This patch enables the On-Chip SRAM (OCRAM) on i.MX53 and i.MX6 SoCs. Signed-off-by:
-
Markus Pargmann authored
Board files for Phytec phyCARD-S "System on Module" and "Rapid Development Kit". Based on patches from: Steffen Trumtrar <s.trumtrar@pengutronix.de>: - Original patch - ARM: dts: Set partition offsets for phycard - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions Jan Luebbe <jlu@pengutronix.de>: - ARM: dts: Enable bad block table in NAND Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de> Cc: Jan Luebbe <jlu@pengutronix.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Markus Pargmann authored
Set operating-points for imx27. There is no regulator support, so the voltages are 0. The frequencies should be the same for all imx27 boards, so it is defined here and can be overwritten if necessary. Signed-off-by:
-
Markus Pargmann authored
Signed-off-by:
-
Markus Pargmann authored
Signed-off-by:
-
Fabio Estevam authored
On the MX27 Reference Manual the interrupt controller is named AITC: ARM926EJ-S Interrupt Controller So use the AITC term instead of AVIC. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Sascha Hauer authored
This adds pinmux entries for USBH1/2 in ULPI mode. Signed-off-by:
-
Sascha Hauer authored
The mc13892 driver knows that it needs spi-cs-high, so the mc13892 will work. The dataflash also connected to this bus though can only be probed when the mc13892 is inactive. Due to driver potential differences in the probe order we can only make sure the mc13892 is inactive when we put the information into the devicetree. Signed-off-by:
-
Sascha Hauer authored
For keeping the alphabetical order in the pinmux nodes. Signed-off-by:
-
Sascha Hauer authored
This allows to order the i2c and spi devices correctly. While at it reorder the aliases entries alphabetically. Signed-off-by:
-
Sascha Hauer authored
This allows to order the i2c and spi devices correctly. While at it reorder the aliases entries alphabetically. Signed-off-by:
-
Sascha Hauer authored
This allows to order the i2c and spi devices correctly. While at it reorder the aliases entries alphabetically. Signed-off-by:
-
Sascha Hauer authored
This allows to order the i2c devices correctly. While at it reorder the aliases entries alphabetically. Signed-off-by:
-
Sascha Hauer authored
This allows to order the i2c and spi devices correctly. While at it reorder the aliases entries alphabetically. Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
The i.MX6 gpt is handled by the i.MX31 gpt driver in the kernel, so add a corresponding compatible entry. Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Sascha Hauer authored
The i.MX6Q and i.MX6DL are pin compatible, so the pinmux entries should be in sync. This patch systematically adds the pinmux entries missing from the imx6q to the imx6dl file. Some name inconsistencies and whitespace damage is fixed along the way. Signed-off-by:
-
Alexander Shiyan authored
This patch adds the missing (Keypad Port) KPP devicetree node for i.MX27 CPUs. Signed-off-by:
Alexander Shiyan <eagle.alexander923@gmail.com> Acked-by:
-
