This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off.  This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.

Verified with the following filters :

	handle 1: u32 divisor 1
	u32 ht 800: order 1 link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
	u32 ht 1: order 2 \
	match tcp src 1024 ffff match tcp dst 23 ffff action drop
	handle 2: u32 divisor 1
	u32 ht 800: order 3 link 2: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
	u32 ht 2: order 4 \
	match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock.  So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.

Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for generic Tx checksums to the ixgbevf driver.  It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.

In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
  MACLEN (maximum of 127), retrieved from:
		skb_network_offset()
  IPLEN  (maximum of 511), retrieved from:
		skb_checksum_start_offset() - skb_network_offset()
  TUCMD.L4T indicates offset and if checksum or crc32c, based on:
		skb->csum_offset

The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.

I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.  In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for generic Tx checksums to the ixgbe driver.  It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.

In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
  MACLEN (maximum of 127), retrieved from:
		skb_network_offset()
  IPLEN  (maximum of 511), retrieved from:
		skb_checksum_start_offset() - skb_network_offset()
  TUCMD.L4T indicates offset and if checksum or crc32c, based on:
		skb->csum_offset

The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.

I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit converts commit c762dff2 ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d105 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed.  This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When running certain routing protocols like VRRP, VF guests need the
ability to set the unicast address of the interface.  Extend the new ndo
trust feature to let the hypervisor trust a guest to set/update its own
unicast address.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the reset flags to adapter->state in order to make use of bit
operations.

This is an alternative patch to the one previously submitted by
John Greene.
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Reported-by: Scott Otto <otts62@yahoo.com>
Reported-by: John Greene <jogreene@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It seem to be non intentionally changed to Tx in
commit adc81090 ("ixgbe: Refactor busy poll socket code to address
multiple issues")

Lock is taken from ixgbe_low_latency_recv, and there under this
lock we use ixgbe_clean_rx_irq so it looks wrong for me to increment
Tx counter.

Yield stats can be shown through ethtool:
ethtool -S enp129s0 | grep yield
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Alexandre TORGUE says:

====================
Enhance stmmac driver to support GMAC4.x IP

This is a subset of patch to enhance current stmmac driver to support
new GMAC4.x chips. New set of callbacks is defined to support this new
family: descriptors, dma, core.

One of main changes of GMAC 4.xx IP is descriptors management.
 -descriptors are only used in ring mode.
 -A descriptor is composed of 4 32bits registers (no more extended
  descriptors)
 -descriptor mechanism (Tx for example, but it is exactly the same for RX):
 -useful registers:
  -DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
  -DMA_CH#_TxDesc_List_Address: start address of the ring
  -DMA_CH#_TxDesc_Tail_Pointer: address of the last descriptor to send + 1.
  -DMA_CH#_TxDesc_Current_App_TxDesc: address of the current descriptor

 -The descriptor Tail Pointer register contains the pointer to the
  descriptor address (N). The base address and the current
  descriptor decide the address of the current descriptor that the
  DMA can process. The descriptors up to one location less than the
  one indicated by the descriptor tail pointer (N-1) are owned by
  the DMA. The DMA continues to process the descriptors until the
  following condition occurs:
  "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

New features are available on IP:
 -TSO (TCP Segmentation Offload) for TX only
 -Split header: to have header and payload in 2 different buffers (not yet implemented)

Below some throughput figures obtained on some boxes:

                        iperf (mbps)
--------------------------------------
                       tcp     udp
                    tx   rx   tx  rx
                     -----------------
    GMAC4.x         935  930  750 800

Note: There is a change in 4.10a databook on bitfield mapping of DMA_CHANx_INTR_ENA register.
This requires to have é diffrent set of callbacks between IP 4.00a and 4.10a.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch just updates the driver to the version fully
tested on STi platforms. This version is Jan_2016.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update stmmac driver documentation according to new GMAC 4.x family.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For gmac3, the MMC addr map is: 0x100 - 0x2fc
For gmac4, the MMC addr map is: 0x700 - 0x8fc

So instead of adding 0x600 to the IO address when setup the mmc,
the RMON base address is saved inside the private structure and
then used to manage the counters.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA behavior is linked to descriptor management:

-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
					      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
						    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"

The DMA automatically wraps around the base address when the end
of ring is reached.

Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the main header file to define all the
macro used for GMAC4 DMA and CORE parts.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
 descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
	-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
				   ring
	-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
				      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
					    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new
      transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
       1) service ports can disable rx pause frame,
       2) debug ports can open tx/rx pause frame.

And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-SACK connections, cwnd is lowered to inflight plus 3 packets
when the recovery ends. This is an optional feature in the NewReno
RFC 2582 to reduce the potential burst when cwnd is "re-opened"
after recovery and inflight is low.

This feature is questionably effective because of PRR: when
the recovery ends (i.e., snd_una == high_seq) NewReno holds the
CA_Recovery state for another round trip to prevent false fast
retransmits. But if the inflight is low, PRR will overwrite the
moderated cwnd in tcp_cwnd_reduction() later regardlessly. So if a
receiver responds bogus ACKs (i.e., acking future data) to speed up
transfer after recovery, it can only induce a burst up to a window
worth of data packets by acking up to SND.NXT. A restart from (short)
idle or receiving streched ACKs can both cause such bursts as well.

On the other hand, if the recovery ends because the sender
detects the losses were spurious (e.g., reordering). This feature
unconditionally lowers a reverted cwnd even though nothing
was lost.

By principle loss recovery module should not update cwnd. Further
pacing is much more effective to reduce burst. Hence this patch
removes the cwnd moderation feature.

v2 changes: revised commit message on bogus ACKs and burst, and
            missing signature
Signed-off-by: Matt Mathis <mattmathis@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Missing device reference in IPSEC input path results in crashes
    during device unregistration.  From Subash Abhinov Kasiviswanathan.

 2) Per-queue ISR register writes not being done properly in macb
    driver, from Cyrille Pitchen.

 3) Stats accounting bugs in bcmgenet, from Patri Gynther.

 4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
    Quentin Armitage.

 5) SXGBE driver has off-by-one in probe error paths, from Rasmus
    Villemoes.

 6) Fix race in save/swap/delete options in netfilter ipset, from
    Vishwanath Pai.

 7) Ageing time of bridge not set properly when not operating over a
    switchdev device.  Fix from Haishuang Yan.

 8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
    Duyck.

 9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.

10) FEC driver should only access registers that actually exist on the
    given chipset, fix from Fabio Estevam.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
  net: mvneta: fix changing MTU when using per-cpu processing
  stmmac: fix MDIO settings
  Revert "stmmac: Fix 'eth0: No PHY found' regression"
  stmmac: fix TX normal DESC
  net: mvneta: use cache_line_size() to get cacheline size
  net: mvpp2: use cache_line_size() to get cacheline size
  net: mvpp2: fix maybe-uninitialized warning
  tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
  net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
  rtnl: fix msg size calculation in if_nlmsg_size()
  fec: Do not access unexisting register in Coldfire
  net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
  net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
  bpf: make padding in bpf_tunnel_key explicit
  ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
  bnxt_en: Fix ethtool -a reporting.
  bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
  bnxt_en: Implement proper firmware message padding.
  ...

Pull clk fixes from Stephen Boyd:
 "A handful of const updates for reset ops and a couple fixes to the
  newly introduced IPQ4019 clock driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
  clk: qcom: ipq4019: switch remaining defines to enums
  clk: qcom: Make reset_control_ops const
  clk: tegra: Make reset_control_ops const
  clk: sunxi: Make reset_control_ops const
  clk: atlas7: Make reset_control_ops const
  clk: rockchip: Make reset_control_ops const
  clk: mmp: Make reset_control_ops const
  clk: mediatek: Make reset_control_ops const

Pull power management and ACPI fix from Rafael J. Wysocki:
 "Just one fix for a nasty boot failure on some systems based on Intel
  Skylake that shipped with broken firmware where enabling
  hardware-coordinated P-states management (HWP) causes a faulty
  interrupt handler in SMM to be invoked and crash the system (Srinivas
  Pandruvada)"

* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / processor: Request native thermal interrupt handling via _OSC

Merge fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  .mailmap: add Christophe Ricard
  Make CONFIG_FHANDLE default y
  mm/page_isolation.c: fix the function comments
  oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
  mm/page_isolation: fix tracepoint to mirror check function behavior
  mm/rmap: batched invalidations should use existing api
  x86/mm: TLB_REMOTE_SEND_IPI should count pages
  mm: fix invalid node in alloc_migrate_target()
  include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
  mm, kasan: fix compilation for CONFIG_SLAB
  MAINTAINERS: orangefs mailing list is subscribers-only

* acpi-processor:
  ACPI / processor: Request native thermal interrupt handling via _OSC

Pull btrfs fixes from Chris Mason:
 "This has a few fixes Dave Sterba had queued up.  These are all pretty
  small, but since they were tested I decided against waiting for more"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: transaction_kthread() is not freezable
  btrfs: cleaner_kthread() doesn't need explicit freeze
  btrfs: do not write corrupted metadata blocks to disk
  btrfs: csum_tree_block: return proper errno value

Pull OrangeFS fixes from Martin Brandenburg:
 "Two bugfixes for OrangeFS.

  One is a reference counting bug and the other is a typo in client
  minimum version"

* tag 'for-linus' of git://github.com/martinbrandenburg/linux:
  orangefs: minimum userspace version is 2.9.3
  orangefs: don't put readdir slot twice

Pull arm64 fixes from Will Deacon:

 - fix oops when patching in alternative sequences on big-endian CPUs

 - reconcile asm/perf_event.h after merge window fallout with KVM ARM

 - defconfig updates

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: defconfig: updates for 4.6
  arm64: perf: Move PMU register related defines to asm/perf_event.h
  arm64: opcodes.h: Add arm big-endian config options before including arm header

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes:

   - a fix in ALSA timer core to avoid possible BUG() trigger
   - a fix in ALSA timer core 32bit compat layer
   - a few HD-audio quirks for ASUS and HP machines
   - AMD HD-audio HDMI controller quirks
   - fixes of USB-audio double-free at some error paths
   - a fix for memory leak in DICE driver at hotunplug"

* tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: timer: Use mod_timer() for rearming the system timer
  ALSA: hda - fix front mic problem for a HP desktop
  ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
  ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
  ALSA: dice: fix memory leak when unplugging
  ALSA: hda - Apply fix for white noise on Asus N550JV, too
  ALSA: hda - Fix white noise on Asus N750JV headphone
  ALSA: hda - Asus N750JV external subwoofer fixup
  ALSA: timer: fix gparams ioctl compatibility for different architectures