- 05 Dec, 2019 17 commits
-
-
George Shen authored
[Why] When a timeout occurs after a DEFER, some devices require more retries than in the case of a regular timeout. [How] In a timeout occurrence, check whether a DEFER has occurred before the timeout and retry MAX_DEFER_RETRIES retries times instead of MAX_TIMEOUT_RETRIES. Signed-off-by:
George Shen <george.shen@amd.com> Reviewed-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Eric Yang authored
Value obtained from DV is not allowing 8k60 CTA mode with DSC to pass, after checking real value being used in hw, find out that correct value is 3600, which will allow that mode. Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Reviewed-by:
-
Amanda Liu authored
[Why] Screen tearing is present in tests when setting the frame rate to certain fps [How] Revert previous optimizations for low frame rates. Signed-off-by:
Amanda Liu <amanda.liu@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Nikola Cornij authored
[why] During mode transition steer fifo could overflow. Quite often it recovers by itself, but sometimes it doesn't. [how] Add steer fifo reset before unblanking the stream. Also add a short delay when resetting dig resync fifo to make sure register writes don't end up back-to-back, in which case the HW might miss the reset request. Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
-
Brandon Syu authored
[Why] The variable mismatch assignment error. [How] To use uint32_t replace it. Signed-off-by:
Brandon Syu <Brandon.Syu@amd.com> Reviewed-by:
Charlene Liu <Charlene.Liu@amd.com> Acked-by:
-
Leo (Hanghong) Ma authored
[why] DP spec requires 1000 symbols delay between the end of link training and enabling FEC in the stream. Currently we are using 1 miliseconds delay which is not accurate. [how] One lane RBR should have the maximum time for transmitting 1000 LL codes which is 6.173 us. So using 7 microseconds delay instead of 1 miliseconds. Signed-off-by:
Leo (Hanghong) Ma <hanghong.ma@amd.com> Reviewed-by:
Harry Wentland <Harry.Wentland@amd.com> Reviewed-by:
-
Joseph Gravenor authored
[Why] new sr and pstate latencies are optimized for the case when we are not using lpddr4 memory [How] have two different wm tables, one for the lpddr case and one for non lpddr case Signed-off-by:
Joseph Gravenor <joseph.gravenor@amd.com> Reviewed-by:
-
David Galiffi authored
[Why] In dc_link_is_dp_sink_present, if dal_ddc_open fails, then dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They are created only on dc_construct, and next aux access will cause a panic. [How] Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close. Signed-off-by:
David Galiffi <David.Galiffi@amd.com> Reviewed-by:
-
Joseph Gravenor authored
[Why] When video_memory_type bw_params->vram_type is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType. Because of this we will never report that we are using LpDdr4MemType and never re-purpose WM set D [How] populate bios integrated info for renoir by adding the revision number for renoir and use that integrated info table instead of of asic_id to get the vram type Signed-off-by:
-
Joseph Gravenor authored
[why] pstate_latency_us never gets updated from the hard coded value in rn_clk_mgr.c [how] update the wm table's values before we do calculations with them Signed-off-by:
-
Nikola Cornij authored
[why] On ASICs where number of DSCs is the same as OPPs there's no need for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3- -related issues for such platforms. [how] Map DSC resources 1-to-1 to pipes only if number of OPPs is the same as number of DSCs. This will still keep other ASICs working. A follow-up patch to fix mode-set issues on those ASICs will be required if testing shows issues with mode set. Signed-off-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
-
Eric Yang authored
[Why] DF team has produced more optimized latency numbers. [How] Add sr latencies to the wm table, use different latencies for different wm sets. Also fix bb override from registery key for these latencies. Signed-off-by:
-
Pierre-Eric Pelloux-Prayer authored
The same workaround is used for gfx7. Both PAL and Mesa use it for gfx8 too, so port this commit to gfx_v8_0_ring_emit_fence_gfx. Signed-off-by:
Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com> Reviewed-by:
-
Alex Deucher authored
So the output is consistent with other asics. Reviewed-by:
Evan Quan <evan.quan@amd.com> Signed-off-by:
-
Guchun Chen authored
When security violation from new vbios happens, data fabric is risky to stop working. So prevent the direct access to DF mmFabricConfigAccessControl from the new vbios and onwards. Signed-off-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
-
Dave Airlie authored
Merge tag 'drm-misc-next-fixes-2019-12-04' of git://anongit.freedesktop.org/drm/drm-misc into drm-next mgag200- Fix hw with broken 'startadd' support (Thomas) mst- Avoid skipping payloads in payload deletion loop (Wayne) omap- Fix dma_addr refcounting (Tomi) Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20191204212255.GA256395@art_vandelay
-
git://anongit.freedesktop.org/tegra/linuxDave Airlie authored
drm/tegra: Fixes for v5.5-rc1 This is a set of small fixes, mostly for regressions introduced with the DMA API and DisplayPort support in the main pull request for v5.5-rc1. Signed-off-by:
-
- 04 Dec, 2019 17 commits
-
-
Wayne Lin authored
[Why] If the payload_state is DP_PAYLOAD_DELETE_LOCAL in series, current code doesn't delete the payload at current index and just move the index to next one after shuffling payloads. [How] Drop the i++ increasing part in for loop head and decide whether to increase the index or not according to payload_state of current payload. Changes since v1: * Refine the code to have it easy reading * Amend the commit message to meet the way code is modified now. Signed-off-by:
Wayne Lin <Wayne.Lin@amd.com> Reviewed-by:
Lyude Paul <lyude@redhat.com> Fixes: 706246c7 ("drm/dp_mst: Refactor drm_dp_update_payload_part1()") Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Juston Li <juston.li@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v5.1+ [Added cc for stable] Signed-off-by:
-
Tomi Valkeinen authored
cec4fa75 ("drm/omap: use refcount API to track the number of users of dma_addr") changed omap_gem.c to use refcounting API to track dma_addr uses. However, the driver only tracks the refcounts for non-contiguous buffers, and the patch didn't fully take this in account. After the patch, the driver always decreased refcount in omap_gem_unpin, instead of decreasing the refcount only for non-contiguous buffers. This leads to refcounting mismatch. As for the contiguous cases the refcount is never increased, fix this issue by returning from omap_gem_unpin if the buffer being unpinned is contiguous. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191114080343.30704-1-tomi.valkeinen@ti.com Fixes: cec4fa75 ("drm/omap: use refcount API to track the number of users of dma_addr") Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
-
Thierry Reding authored
The call to tegra_display_hub_cleanup() that takes care of disabling the window groups is missing from the driver's ->remove() callback. Call it to make sure the runtime PM reference counts for the display controllers are balanced. Signed-off-by:Thierry Reding <treding@nvidia.com>
-
Thierry Reding authored
The SOR supports multiple display modes, but only when driving an HDMI monitor does it make sense to control the +5V power supply. eDP and DP don't need this, so make it optional. This fixes a crash observed during system suspend/resume. Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Thierry Reding authored
Subdevices may not be hooked up to an IOMMU via device tree. Detect such situations and avoid confusing users by not emitting an error message. Reviewed-by:
-
Thierry Reding authored
Export the module device table to ensure the VIC compatible strings are listed in the module's aliases table. This in turn causes the driver to be automatically loaded on boot if VIC is the only enabled subdevice of the logical host1x DRM device. Reviewed-by:
-
Thierry Reding authored
Upon system suspend, make sure the +5V HDMI regulator is disabled. This avoids potentially leaking current to the HDMI connector. This also makes sure that upon resume the regulator is enabled again, which in some cases is necessary to properly restore the state of the supply on resume. Reviewed-by:
-
Thierry Reding authored
The IOVA address for the cursor is the result of mapping the buffer object for the given display controller. Make sure to use the proper IOVA address as stored in the cursor's plane state. Reviewed-by:
-
Thierry Reding authored
All the display related blocks on Tegra require contiguous memory. Using the DMA API, there is no knowing at import time which device will end up using the buffer, so it's not known whether or not an IOMMU will be used to map the buffer. Move the check for non-contiguous buffers/mappings to the tegra_dc_pin() function which is now the earliest point where it is known if a DMA BUF can be used by the given device or not. v2: add check for contiguous buffer/mapping in tegra_dc_pin() Reviewed-by:
-
Thierry Reding authored
Buffers that are imported from a DMA-BUF don't have pages allocated with them. At the same time an SG table for them can't be derived using the DMA API helpers because the necessary information doesn't exist. However there's already an SG table that was created during import, so this can simply be duplicated. Signed-off-by: -
Thierry Reding authored
The Tegra DRM never actually took that lock, so the driver was broken until generic locking was added in commit: commit b962a120 Author: Rob Clark <robdclark@gmail.com> Date: Mon Oct 22 14:31:22 2018 +0200 drm/atomic: integrate modeset lock with private objects It's now no longer necessary to take that lock, so drop the check. v2: add rationale for why it is now safe to drop the check (Daniel) Reviewed-by:
-
Corentin Labbe authored
It's dangerous to use empty code define. Furthermore it lead to the following warning: drivers/char/agp/generic.c: In function « agp_generic_destroy_page »: drivers/char/agp/generic.c:1266:28: attention : suggest braces around empty body in an « if » statement [-Wempty-body] So let's replace emptyness by "do {} while(0)" Signed-off-by:Corentin Labbe <clabbe@baylibre.com> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Corentin Labbe authored
This patch add documentation about the bridge parameter in several function. This will fix the following build warning: drivers/char/agp/generic.c:220: warning: No description found for parameter 'bridge' drivers/char/agp/generic.c:364: warning: No description found for parameter 'bridge' drivers/char/agp/generic.c:1283: warning: No description found for parameter 'bridge' Signed-off-by:
-
Corentin Labbe authored
This patch fix the following build warning: warning: variable 'num_segments' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Corentin Labbe authored
This patch move the define for AGPGART_MINOR to include/linux/miscdevice.h. It is better that all minor number definitions are in the same place. Signed-off-by:
-
Corentin Labbe authored
This patch fix the following warning: drivers/char/agp/generic.c:853:6: attention : variable ‘size’ set but not used [-Wunused-but-set-variable] by removing the unused variable size in agp_generic_create_gatt_table Signed-off-by:
-
git://people.freedesktop.org/~agd5f/linuxDave Airlie authored
drm-next-5.5-2019-12-03: amdgpu: - Fix vram lost handling with BACO on VI/CI asics - DC fixes for Navi14 - Misc gfx10 fixes - SR-IOV fixes - Fix driver unload - Fix XGMI limits on Arcturus amdkfd: - Enable KFD on PPC - Optimize KFD page table reservations radeon: - Fix register checker for r1xx/r2xx Signed-off-by:
-
- 03 Dec, 2019 6 commits
-
-
Guenter Roeck authored
On systems with STACKTRACE_SUPPORT=n, we get: WARNING: unmet direct dependencies detected for STACKTRACE Depends on [n]: STACKTRACE_SUPPORT Selected by [y]: - STACKDEPOT [=y] and build errors such as: m68k-linux-ld: kernel/stacktrace.o: in function `stack_trace_save': (.text+0x11c): undefined reference to `save_stack_trace' Add the missing deendency on STACKTRACE_SUPPORT. Fixes: 12a280c7 ("drm/dp_mst: Add topology ref history tracking for debugging") Cc: Lyude Paul <lyude@redhat.com> Cc: Sean Paul <sean@poorly.run> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Alex Deucher authored
Shift and mask were reversed. Noticed by chance. Tested-by:
Meelis Roos <mroos@linux.ee> Reviewed-by:
Michel Dänzer <mdaenzer@redhat.com> Signed-off-by:
-
Monk Liu authored
still need to init csb even for SRIOV v2: drop init_pg() for gfx10 at all since PG and GFX off feature will be fully controled by RLC and SMU fw for gfx10 v3: drop the flush_gpu_tlb lines since we consider it is only usefull in emulation Signed-off-by:
Monk Liu <Monk.Liu@amd.com> Reviewed-by:
-
Monk Liu authored
To align with the scheme from gfx9 disabling GFX ring after VM shutdown could avoid garbage data be fetched to GFX RB which may lead to unnecessary screw up on GFX Signed-off-by:
-
Monk Liu authored
since we don't have RLCG ucode loading and no SRlist as well Signed-off-by:
-
Monk Liu authored
Signed-off-by:
-
