This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.

Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.

Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:

arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The device node name should reflect generic class of a device so rename
the "iram" node to "sram".  This will be also in sync with upcoming DT
schema.  No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"internal_j8" and "internal_j9" are network interfaces that are not
exposed outside the board and were only ever used for debugging purposes.

Get rid of them as they are not needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Wandboard devicetrees lack the ethernet PHY description, add it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the CAN enablement from SoM DTSi to board DTS, as each board might need
different CAN configuration. Moreover, disable CAN2 on the PDK2 as it is not
available on any connector. This also fixes on-SoM SD slot operation, as it
shares pins with the CAN2.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add "opp-suspend" property for i.MX7D to make sure system
suspend with max available opp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 800MHz opp speed grading fuse mask should be 0xd instead
of 0xf according to fuse map definition:

SPEED_GRADING[1:0]	MHz
	00		800
	01		500
	10		1000
	11		1200
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.

Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:

arch/arm/boot/dts/imx6qdl-gw551x.dtsi:109.32-121.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass the memory unit name in order to fix the following build warning
with W=1:

arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi:23.9-26.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name

Cc: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Replace "simple-bus" with "simple-mfd" for anatop node in order
to fix the following build warnings with W=1:

arch/arm/boot/dts/imx6sx.dtsi:603.31-616.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-1p1: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:618.31-631.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-3p0: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:633.31-646.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-2p5: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:648.32-663.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:665.33-679.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpcie: missing or empty reg/ranges property
arch/arm/boot/dts/imx6sx.dtsi:681.31-696.7: Warning (simple_bus_reg): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc: missing or empty reg/ranges property

Based on a patch from Marco Felsch for the imx6qdl.dtsi.

Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add wdog1 node to support watchdog driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Pincfgs to enable the i.MX6's OTG feature for UDOO
Signed-off-by: Markus Kueffner <kueffner.markus@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the possibility to wake the module with an external signal
as defined in the Colibri standard
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan nodes to imx6ull-colibri-eval-v3.dtsi
where they belong.

Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reduce the current drawn from VCC_BATT when the main power on the 3V3
pins to the module are switched off.

This switches off SoC internal pull resistors which are provided on the
module for TAMPER7 and TAMPER9 SoC pin and switches on a pull down
instead of a pullup for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Do not change the clock as the power for this phy is switched
with that clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds some missing pinmuxing that is in the colibri
standard to the dts.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit adds the touchscreen from Toradex so one can enable it.
It is disabled by default because the pins are also used for PWM<B>,
PWM<C>, aka pwm2, pwm3 which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch prepares the devicetree for the new Ixora V1.2 where we are
able to turn off the supply of the can transceiver. This implies to use
a sleep state on transmission pins in order to prevent backfeeding.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the muxing for the optional pins usb-oc (overcurrent) and
usb-id.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add touch controller that is connected over an I2C bus.
It is disabled by default because the pins are also used for PWM,
which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add pinmuxing and do not specify voltage restrictions for the usdhc
instance available on the modules edge connector. This allows to use
SD-cards with higher transfer modes if supported by the carrier board.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add wakeup GPIO key which is able to wake the system from sleep
modes (e.g. Suspend-to-Memory).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the IMX7ULP reference manual, the mipi pll
clock comes from the MIPI PHY PLL output. So it should
not be defined as a fixed clock. So remove this clock
node and all the references to it.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LPUART driver does not support specifying "rs485-rts-delay"
property. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rework the device trees of the OPOS6UL and OPOS6ULDev boards to support
the OPOS6UL SoM with an i.MX6ULL SoC.  The device trees are now as
following:

- imx6ul-imx6ull-opos6ul.dtsi
  common for both i.MX6UL and i.MX6ULL OPOS6UL SoM.
- imx6ul-opos6ul.dtsi
  for i.MX6UL OPOS6UL SoM. It includes imx6ul.dtsi and
  imx6ul-imx6ull-opos6ul.dtsi.
- imx6ull-opos6ul.dtsi
  for i.MX6ULL OPOS6UL SoM. It includes imx6ull.dtsi and
  imx6ul-imx6ull-opos6ul.dtsi.

- imx6ul-imx6ull-opos6uldev.dtsi
  OPOS6ULDev base device tree.
- imx6ul-opos6uldev.dts
  OPOS6ULDev board with an i.MX6UL OPOS6UL SoM. It includes
  imx6ul-opos6ul.dtsi and imx6ul-imx6ull-opos6uldevdtsi.
- imx6ull-opos6uldev.dts
  OPOS6ULDev board with an i.MX6ULL OPOS6UL SoM. It includes
  imx6ull-opos6ul.dtsi and imx6ul-imx6ull-opos6uldevdtsi.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Pull Documentation/process update from Greg KH:
 "Here are two small Documentation/process/embargoed-hardware-issues.rst
  file updates that missed my previous char/misc pull request.

  The first one adds an Intel representative for the process, and the
  second one cleans up the text a bit more when it comes to how the
  disclosure rules work, as it was a bit confusing to some companies"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Documentation/process: Clarify disclosure rules
  Documentation/process: Volunteer as the ambassador for Intel

Pull more vfs updates from Al Viro:
 "A couple of misc patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs dynroot: switch to simple_dir_operations
  fs/handle.c - fix up kerneldoc

Pull more cifs updates from Steve French:
 "Fixes from the recent SMB3 Test events and Storage Developer
  Conference (held the last two weeks).

  Here are nine smb3 patches including an important patch for debugging
  traces with wireshark, with three patches marked for stable.

  Additional fixes from last week to better handle some newly discovered
  reparse points, and a fix the create/mkdir path for setting the mode
  more atomically (in SMB3 Create security descriptor context), and one
  for path name processing are still being tested so are not included
  here"

* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix oplock handling for SMB 2.1+ protocols
  smb3: missing ACL related flags
  smb3: pass mode bits into create calls
  smb3: Add missing reparse tags
  CIFS: fix max ea value size
  fs/cifs/sess.c: Remove set but not used variable 'capabilities'
  fs/cifs/smb2pdu.c: Make SMB2_notify_init static
  smb3: fix leak in "open on server" perf counter
  smb3: allow decryption keys to be dumped by admin for debugging