Pull MMC updates from Chris Ball:
 "MMC highlights for 3.8:

  Core:
   - Expose access to the eMMC RPMB ("Replay Protected Memory Block")
     area by extending the existing mmc_block ioctl.
   - Add SDIO powered-suspend DT properties to the core MMC DT binding.
   - Add no-1-8-v DT flag for boards where the SD controller reports
     that it supports 1.8V but the board itself has no way to switch to
     1.8V.
   - More work on switching to 1.8V UHS support using a vqmmc regulator.
   - Fix up a case where the slot-gpio helper may fail to reset the host
     controller properly if a card was removed during a transfer.
   - Fix several cases where a broken device could cause an infinite
     loop while we wait for a register to update.

  Drivers:
   - at91-mci: Remove obsolete driver, atmel-mci handles these devices
     now.
   - sdhci-dove: Allow using GPIOs for card-detect notifications.
   - sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
   - sdhci-s3c: Add pinctrl support.
   - wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."

* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
  mmc: sdhci: implement the .card_event() method
  mmc: extend the slot-gpio card-detection to use host's .card_event() method
  mmc: add a card-event host operation
  mmc: sdhci-s3c: Fix compilation warning
  mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
  mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
  mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
  mmc: sdhci-dove: use devm_clk_get()
  mmc: eSDHC: Recover from ADMA errors
  mmc: dw_mmc: remove duplicated buswidth code
  mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
  mmc: Limit MMC speed to 52MHz if not HS200
  mmc: dw_mmc: use devres functions in dw_mmc
  mmc: sh_mmcif: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: remove unneeded clock connection ID
  mmc: sh_mobile_sdhi: fix clock frequency printing
  mmc: Remove redundant null check before kfree in bus.c
  mmc: Remove redundant null check before kfree in sdio_bus.c
  mmc: sdhci-imx-esdhc: use more devm_* functions
  mmc: dt: add no-1-8-v device tree flag
  ...

The matrix-keymap module is currently lacking a proper module license,
add one so we don't have this module tainting the entire kernel.  This
issue has been present since commit 1932811f ("Input: matrix-keymap
- uninline and prepare for device tree support")
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@vger.kernel.org # v3.5+
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Netlink socket dumping had several missing verifications and checks.

    In particular, address comparisons in the request byte code
    interpreter could access past the end of the address in the
    inet_request_sock.

    Also, address family and address prefix lengths were not validated
    properly at all.

    This means arbitrary applications can read past the end of certain
    kernel data structures.

    Fixes from Neal Cardwell.

 2) ip_check_defrag() operates in contexts where we're in the process
    of, or about to, input the packet into the real protocols
    (specifically macvlan and AF_PACKET snooping).

    Unfortunately, it does a pskb_may_pull() which can modify the
    backing packet data which is not legal if the SKB is shared.  It
    very much can be shared in this context.

    Deal with the possibility that the SKB is segmented by using
    skb_copy_bits().

    Fix from Johannes Berg based upon a report by Eric Leblond.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  ipv4: ip_check_defrag must not modify skb before unsharing
  inet_diag: validate port comparison byte code to prevent unsafe reads
  inet_diag: avoid unsafe and nonsensical prefix matches in inet_diag_bc_run()
  inet_diag: validate byte code to prevent oops in inet_diag_bc_run()
  inet_diag: fix oops for IPv4 AF_INET6 TCP SYN-RECV state

This reverts commits a5091539 and
d7c3b937.

This is a revert of a revert of a revert.  In addition, it reverts the
even older i915 change to stop using the __GFP_NO_KSWAPD flag due to the
original commits in linux-next.

It turns out that the original patch really was bogus, and that the
original revert was the correct thing to do after all.  We thought we
had fixed the problem, and then reverted the revert, but the problem
really is fundamental: waking up kswapd simply isn't the right thing to
do, and direct reclaim sometimes simply _is_ the right thing to do.

When certain allocations fail, we simply should try some direct reclaim,
and if that fails, fail the allocation.  That's the right thing to do
for THP allocations, which can easily fail, and the GPU allocations want
to do that too.

So starting kswapd is sometimes simply wrong, and removing the flag that
said "don't start kswapd" was a mistake.  Let's hope we never revisit
this mistake again - and certainly not this many times ;)
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ip_check_defrag() might be called from af_packet within the
RX path where shared SKBs are used, so it must not modify
the input SKB before it has unshared it for defragmentation.
Use skb_copy_bits() to get the IP header and only pull in
everything later.

The same is true for the other caller in macvlan as it is
called from dev->rx_handler which can also get a shared SKB.
Reported-by: Eric Leblond <eric@regit.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 782fd304.

We are going to reinstate the __GFP_NO_KSWAPD flag that has been
removed, the removal reverted, and then removed again.  Making this
commit a pointless fixup for a problem that was caused by the removal of
__GFP_NO_KSWAPD flag.

The thing is, we really don't want to wake up kswapd for THP allocations
(because they fail quite commonly under any kind of memory pressure,
including when there is tons of memory free), and these patches were
just trying to fix up the underlying bug: the original removal of
__GFP_NO_KSWAPD in commit c6543459 ("mm: remove __GFP_NO_KSWAPD")
was simply bogus.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add logic to verify that a port comparison byte code operation
actually has the second inet_diag_bc_op from which we read the port
for such operations.

Previously the code blindly referenced op[1] without first checking
whether a second inet_diag_bc_op struct could fit there. So a
malicious user could make the kernel read 4 bytes beyond the end of
the bytecode array by claiming to have a whole port comparison byte
code (2 inet_diag_bc_op structs) when in fact the bytecode was not
long enough to hold both.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add logic to check the address family of the user-supplied conditional
and the address family of the connection entry. We now do not do
prefix matching of addresses from different address families (AF_INET
vs AF_INET6), except for the previously existing support for having an
IPv4 prefix match an IPv4-mapped IPv6 address (which this commit
maintains as-is).

This change is needed for two reasons:

(1) The addresses are different lengths, so comparing a 128-bit IPv6
prefix match condition to a 32-bit IPv4 connection address can cause
us to unwittingly walk off the end of the IPv4 address and read
garbage or oops.

(2) The IPv4 and IPv6 address spaces are semantically distinct, so a
simple bit-wise comparison of the prefixes is not meaningful, and
would lead to bogus results (except for the IPv4-mapped IPv6 case,
which this commit maintains).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add logic to validate INET_DIAG_BC_S_COND and INET_DIAG_BC_D_COND
operations.

Previously we did not validate the inet_diag_hostcond, address family,
address length, and prefix length. So a malicious user could make the
kernel read beyond the end of the bytecode array by claiming to have a
whole inet_diag_hostcond when the bytecode was not long enough to
contain a whole inet_diag_hostcond of the given address family. Or
they could make the kernel read up to about 27 bytes beyond the end of
a connection address by passing a prefix length that exceeded the
length of addresses of the given family.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix inet_diag to be aware of the fact that AF_INET6 TCP connections
instantiated for IPv4 traffic and in the SYN-RECV state were actually
created with inet_reqsk_alloc(), instead of inet6_reqsk_alloc(). This
means that for such connections inet6_rsk(req) returns a pointer to a
random spot in memory up to roughly 64KB beyond the end of the
request_sock.

With this bug, for a server using AF_INET6 TCP sockets and serving
IPv4 traffic, an inet_diag user like `ss state SYN-RECV` would lead to
inet_diag_fill_req() causing an oops or the export to user space of 16
bytes of kernel memory as a garbage IPv6 address, depending on where
the garbage inet6_rsk(req) pointed.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit c702418f ("mm: vmscan: do not keep kswapd looping forever due
to individual uncompactable zones") removed zone watermark checks from
the compaction code in kswapd but left in the zone congestion clearing,
which now happens unconditionally on higher order reclaim.

This messes up the reclaim throttling logic for zones with
dirty/writeback pages, where zones should only lose their congestion
status when their watermarks have been restored.

Remove the clearing from the zone compaction section entirely.  The
preliminary zone check and the reclaim loop in kswapd will clear it if
the zone is considered balanced.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The direct-IO write path already had the i_size checks in mm/filemap.c,
but it turns out the read path did not, and removing the block size
checks in fs/block_dev.c (commit bbec0270: "blkdev_max_block: make
private to fs/buffer.c") removed the magic "shrink IO to past the end of
the device" code there.

Fix it by truncating the IO to the size of the block device, like the
write path already does.

NOTE! I suspect the write path would be *much* better off doing it this
way in fs/block_dev.c, rather than hidden deep in mm/filemap.c.  The
mm/filemap.c code is extremely hard to follow, and has various
conditionals on the target being a block device (ie the flag passed in
to 'generic_write_checks()', along with a conditional update of the
inode timestamp etc).

It is also quite possible that we should treat this whole block device
size as a "s_maxbytes" issue, and try to make the logic even more
generic.  However, in the meantime this is the fairly minimal targeted
fix.

Noted by Milan Broz thanks to a regression test for the cryptsetup
reencrypt tool.
Reported-and-tested-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:
 "Two stragglers:

   1) The new code that adds new flushing semantics to GRO can cause SKB
      pointer list corruption, manage the lists differently to avoid the
      OOPS.  Fix from Eric Dumazet.

   2) When TCP fast open does a retransmit of data in a SYN-ACK or
      similar, we update retransmit state that we shouldn't triggering a
      WARN_ON later.  Fix from Yuchung Cheng."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: gro: fix possible panic in skb_gro_receive()
  tcp: bug fix Fast Open client retransmission

commit 2e71a6f8 (net: gro: selective flush of packets) added
a bug for skbs using frag_list. This part of the GRO stack is rarely
used, as it needs skb not using a page fragment for their skb->head.

Most drivers do use a page fragment, but some of them use GFP_KERNEL
allocations for the initial fill of their RX ring buffer.

napi_gro_flush() overwrite skb->prev that was used for these skb to
point to the last skb in frag_list.

Fix this using a separate field in struct napi_gro_cb to point to the
last fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If SYN-ACK partially acks SYN-data, the client retransmits the
remaining data by tcp_retransmit_skb(). This increments lost recovery
state variables like tp->retrans_out in Open state. If loss recovery
happens before the retransmission is acked, it triggers the WARN_ON
check in tcp_fastretrans_alert(). For example: the client sends
SYN-data, gets SYN-ACK acking only ISN, retransmits data, sends
another 4 data packets and get 3 dupacks.

Since the retransmission is not caused by network drop it should not
update the recovery state variables. Further the server may return a
smaller MSS than the cached MSS used for SYN-data, so the retranmission
needs a loop. Otherwise some data will not be retransmitted until timeout
or other loss recovery events.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extracting a part of the SDHCI card tasklet into a .card_event()
implementation allows SDHCI hosts to use generic card-detection
services, e.g. the GPIO slot function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Some hosts need to perform additional actions upon card insertion or
ejection. Add a host operation to be called from card detection handlers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

'sc' is used only when CONFIG_PM_RUNTIME is defined. Hence define it
conditionally.

Silences the following warning:
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:378:20: warning: unused variable ‘sc’ [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Pull MMC fixes from Chris Ball:
 "Two small regression fixes:

   - sdhci-s3c: Fix runtime PM regression against 3.7-rc1
   - sh-mmcif: Fix oops against 3.6"

* tag 'mmc-fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: sh-mmcif: avoid oops on spurious interrupts (second try)
  Revert misapplied "mmc: sh-mmcif: avoid oops on spurious interrupts"
  mmc: sdhci-s3c: fix missing clock for gpio card-detect

This fixes a regression in 3.7-rc, which has since gone into stable.

Commit 00442ad0 ("mempolicy: fix a memory corruption by refcount
imbalance in alloc_pages_vma()") changed get_vma_policy() to raise the
refcount on a shmem shared mempolicy; whereas shmem_alloc_page() went
on expecting alloc_page_vma() to drop the refcount it had acquired.
This deserves a rework: but for now fix the leak in shmem_alloc_page().

Hugh: shmem_swapin() did not need a fix, but surely it's clearer to use
the same refcounting there as in shmem_alloc_page(), delete its onstack
mempolicy, and the strange mpol_cond_copy() and __mpol_cond_copy() -
those were invented to let swapin_readahead() make an unknown number of
calls to alloc_pages_vma() with one mempolicy; but since 00442ad0,
alloc_pages_vma() has kept refcount in balance, so now no problem.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When a zone meets its high watermark and is compactable in case of
higher order allocations, it contributes to the percentage of the node's
memory that is considered balanced.

This requirement, that a node be only partially balanced, came about
when kswapd was desparately trying to balance tiny zones when all bigger
zones in the node had plenty of free memory.  Arguably, the same should
apply to compaction: if a significant part of the node is balanced
enough to run compaction, do not get hung up on that tiny zone that
might never get in shape.

When the compaction logic in kswapd is reached, we know that at least
25% of the node's memory is balanced properly for compaction (see
zone_balanced and pgdat_balanced).  Remove the individual zone checks
that restart the kswapd cycle.

Otherwise, we may observe more endless looping in kswapd where the
compaction code loops back to reclaim because of a single zone and
reclaim does nothing because the node is considered balanced overall.

See for example

  https://bugzilla.redhat.com/show_bug.cgi?id=866988Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-and-tested-by: Thorsten Leemhuis <fedora@leemhuis.info>
Reported-by: Jiri Slaby <jslaby@suse.cz>
Tested-by: John Ellson <john.ellson@comcast.net>
Tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 0bf380bc ("mm: compaction: check pfn_valid when entering a
new MAX_ORDER_NR_PAGES block during isolation for migration") added a
check for pfn_valid() when isolating pages for migration as the scanner
does not necessarily start pageblock-aligned.

Since commit c89511ab ("mm: compaction: Restart compaction from near
where it left off"), the free scanner has the same problem.  This patch
makes sure that the pfn range passed to isolate_freepages_block() is
within the same block so that pfn_valid() checks are unnecessary.

In answer to Henrik's wondering why others have not reported this:
reproducing this requires a large enough hole with the right aligment to
have compaction walk into a PFN range with no memmap.  Size and
alignment depends in the memory model - 4M for FLATMEM and 128M for
SPARSEMEM on x86.  It needs a "lucky" machine.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Ricoh SDHCI controllers support Highspeed clocks as evident from
the ricoh_mmc_probe_slot() settings. Hence, SDHCI_CAN_DO_HISPD needs
to be set to enable SDIO client drivers to set/enable high speed clock
settings
Signed-off-by: Madhvapathi Sriram <Madhvapathi.Sriram@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This commit taken from Rabeeh's Cubox kernel and re-worked for DT;
Sebastian Hasselbrath is believed to be the original author.

Some Cuboxes require a GPIO for card detection; this implements the
optional GPIO support for card detection.  This GPIO is logic 0 for
card inserted.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>

We need to use the two-stage initialization for sdhci-pltfm if we're
going to do anything extra at initialization time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>

Use devm_clk_get() rather than clk_get() to make cleanup paths more simple.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>

A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

ctype is using 1-bit buswidth mode by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag.  If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

If "caps2" host capabilities does not indicate support for MMC
HS200, don't allow clock speeds >52MHz. Currently, for MMC, the
clock speed is set to the lesser of the max speed the eMMC module
supports (card->ext_csd.hs_max_dtr) or the max base clock of the
host controller (host->f_max based on BASE_CLK_FREQ in the host
CAPS register). This means that a host controller that doesn't
support HS200 mode but has a base clock of 100MHz and an eMMC module
that supports HS200 speeds will end up using a 100MHz clock.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Use managed device resource functions for easy handling.
This makes driver simpler in the routine of error and exit.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

MMCIF only uses one clock, all ARM and SuperH platforms register MMCIF
clock lookup entries with no connection ID, hence it can be dropped in
the driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

SDHI only uses one clock, all ARM and SuperH platform register SDHI clock
lookup entries with no connection ID, hence it can be dropped in the
driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

During its probing the SDHI driver prints out the clock frequency, but
does it wrongly, always reporting 0Hz. Use the MMC host frequency value
to fix this issue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>

kfree on a null pointer is a no-op.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

kfree on a null pointer is a no-op.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Use devm_kzalloc, devm_gpio_request_one and devm_request_irq to make
cleanup path simpler.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.

However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.

Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>