This patch adds macro NETCONFA_ALL to represent all type of netconf
attributes for IPv4 and IPv6.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

prior to this patch, at the beginning if we have two paths in one assoc,
they may have the same params other than the last_time_heard, it will try
the paths like this:

1st cycle
  try trans1 fail.
  then trans2 is selected.(cause it's last_time_heard is after trans1).

2nd cycle:
  try  trans2 fail
  then trans2 is selected.(cause it's last_time_heard is after trans1).

3rd cycle:
  try  trans2 fail
  then trans2 is selected.(cause it's last_time_heard is after trans1).

....

trans1 will never have change to be selected, which is not what we expect.
we should keeping round robin all the paths if they are just added at the
beginning.

So at first every tranport's last_time_heard should be initialized 0, so
that we ensure they have the same value at the beginning, only by this,
all the transports could get equal chance to be selected.

Then for sctp_trans_elect_best, it should return the trans_next one when
*trans == *trans_next, so that we can try next if it fails,  but now it
always return trans. so we can fix it by exchanging these two params when
we calls sctp_trans_elect_tie().

Fixes: 4c47af4d ('net: sctp: rework multihoming retransmission path selection to rfc4960')
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace all "unsigned" types with "unsigned int" types.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2016-03-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers patches for 4.6

Major changes:

ath10k

* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip

ath9k

* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels

bcma

* move flash detection code to ChipCommon core driver

brcmfmac

* IPv6 Neighbor discovery offload
* driver settings that can be populated from different sources
* country code setting in firmware
* length checks to validate firmware events
* new way to determine device memory size needed for BCM4366
* various offloads during Wake on Wireless LAN (WoWLAN)
* full Management Frame Protection (MFP) support

iwlwifi

* add support for thermal device / cooling device
* improvements in scheduled scan without profiles
* new firmware support (-21.ucode)
* add MSIX support for 9000 devices
* enable MU-MIMO and take care of firmware restart
* add support for large SKBs in mvm to reach A-MSDU
* add support for filtering frames from a BA session
* start implementing the new Rx path for 9000 devices
* enable the new Radio Resource Management (RRM) nl80211 feature flag
* add a new module paramater to disable VHT
* build infrastructure for Dynamic Queue Allocation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
A couple of minor clean-ups and optimizations

This patch series is basically just a v2 of a couple patches I recently
submitted.

The two patches aren't technically related but there are just items I found
while cleaning up and prepping some further work to enable Tx checksums for
tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The code for csum_block_add was doing a funky byteswap to swap the even and
odd bytes of the checksum if the offset was odd.  Instead of doing this we
can save ourselves some trouble and just shift by 8 as this should have the
same effect in terms of the final checksum value and only requires one
instruction.

In addition we can update csum_block_sub to just use csum_block_add with a
inverse value for csum2.  This way we follow the same code path as
csum_block_add without having to duplicate it.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the GRO handlers for GRE, VXLAN, GENEVE, and FOU so that
we do not clear the flush bit until after we have called the next level GRO
handler.  Previously this was being cleared before parsing through the list
of frames, however this resulted in several paths where either the bit
needed to be reset but wasn't as in the case of FOU, or cases where it was
being set as in GENEVE.  By just deferring the clearing of the bit until
after the next level protocol has been parsed we can avoid any unnecessary
bit twiddling and avoid bugs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is OF-DPA specific, used only there, similar to
ofdpa_port->ageing_time. So move it to OF-DPA code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: Management firmware updates

This series contains several changes to driver interaction with the
management fw.
The biggest [& most significant] change here is a change in the locking
scheme and re-definition of the 'critical section' when accessing shared
resources toward the goal of interacting with the management firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the scenario where slowpath configuration isn't passing due to
various pause configurations affecting the chip, the theoretical time
required in worst-case-scenario to empty hw fifos sufficiently to
guarantee that slowpath configuration would flow is currently
insufficient.

This increases such a drain request to the theoretical maximum.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle a new message from the MFW, one that indicate that the transciever
state has changed, and log that into the system logs.
Signed-off-by: Zvi Nachmani <Zvi.Nachmani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver interaction with the managemnt firmware is done via mailbox
commands which the management firmware periodically sample, as well
as placing of additional data in set places in the shared memory.
Each PF has a single designated mailbox address, and all flows that
require messaging to the management should use it.

This patch does 2 things:
 1. It re-defines the critical section surrounding the mailbox sending -
that section should include the setting of the shared memory as well as
the sending of the command [otherwise a race might send a command with
the data of a different command].
 2. It moves the locking scheme from using mutices into using spinlocks.
This lays the groundwork for sending MFW commands from non-sleepable
contexts.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When device is configured for Multi-function mode, some older management
firmware might incorrectly notify interfaces of link changes while they
haven't requested the physical link configuration to be set.
This can create bizzare race conditions where unloading interfaces are
getting notified that the link is up.

Let the driver compensate - store the logical requested state of the link
and don't propagate notifications after protocol driver explicitly
requires the link to be unset.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
BPF support for flow labels

This set adds support for tunnel key flow labels for vxlan
and geneve devices in collect meta data mode and eBPF support
for managing these. For details please see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extends bpf_tunnel_key with a tunnel_label member, that maps
to ip_tunnel_key's label so underlying backends like vxlan and geneve
can propagate the label to udp_tunnel6_xmit_skb(), where it's being set
in the IPv6 header. It allows for having 20 more bits to encode/decode
flow related meta information programmatically. Tested with vxlan and
geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This work adds support for setting the IPv6 flow label for geneve per
device and through collect metadata (ip_tunnel_key) frontends. Also here,
the geneve dst cache does not need any special considerations, for the
cases where caches can be used, the label is static per cache.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This work adds support for setting the IPv6 flow label for vxlan per
device and through collect metadata (ip_tunnel_key) frontends. The
vxlan dst cache does not need any special considerations here, for
the cases where caches can be used, the label is static per cache.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extends udp_tunnel6_xmit_skb() to pass in the IPv6 flow label
from call sites. Currently, there's no such option and it's always set to
zero when writing ip6_flow_hdr(). Add a label member to ip_tunnel_key, so
that flow-based tunnels via collect metadata frontends can make use of it.
vxlan and geneve will be converted to add flow label support separately.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't hide varibles used by the logging macros.

Miscellanea:

o Use the more common ##__VA_ARGS__ extension
o Add missing newlines to formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
bridge: ageing timer regression fix

This fixes regression in how ageing timer is managed.
Backing out the change required fixing switch drivers as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a regression in the bridge ageing time caused by:
commit c62987bb ("bridge: push bridge setting ageing_time down to switchdev")

There are users of Linux bridge which use the feature that if ageing time
is set to 0 it causes entries to never expire. See:
  https://www.linuxfoundation.org/collaborate/workgroups/networking/bridge

For a pure software bridge, it is unnecessary for the code to have
arbitrary restrictions on what values are allowable.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rocker, ageing time is a per-port attribute, so the next time the FDB
cleanup timer fires should be set according to the lowest ageing time.

This will later allow us to delete the BR_MIN_AGEING_TIME macro, which was
added to guarantee minimum ageing time in the bridge layer, thereby breaking
existing behavior.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c62987bb ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.

Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stack expects link layer headers in the skb linear section.
Macvtap can create skbs with llheader in frags in edge cases:
when (IFF_VNET_HDR is off or vnet_hdr.hdr_len < ETH_HLEN) and
prepad + len > PAGE_SIZE and vnet_hdr.flags has no or bad csum.

Add checks to ensure linear is always at least ETH_HLEN.
At this point, len is already ensured to be >= ETH_HLEN.

For backwards compatiblity, rounds up short vnet_hdr.hdr_len.
This differs from tap and packet, which return an error.

Fixes b9fb9ee0 ("macvtap: add GSO/csum offload support")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cast pointer to unsigned long instead of u64, to fix compilation warning
on 32 bit arch, spotted by 0day build.

Fixes: 5b33f488 ("net/flower: Introduce hardware offload support")
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
cls_flower hardware offload support

Please see changes from V2 at the bottom.

This patchset introduces cls_flower hardware offload support over ConnectX-4
driver, more hardware vendors are welcome to use it too.

This patchset is based on John's infrastructure for tc offloading [2] to add
hardware offload support to the flower filter. It also extends the support to
an additional tc action - skbedit mark operation.
NIC driver that was used is ConnectX-4. Feature is off by default and could be
turned on using ethtool.

Some commands to use this code:

export TC=../iproute2/tc/tc
export ETH=ens9

ethtool  -K ens9 hw-tc-offload on

$TC qdisc add dev $ETH ingress

$TC filter add dev $ETH protocol ip prio 20 parent ffff: \
	flower ip_proto 1 \
	dst_mac 7c:fe:90:69:81:62 \
	src_mac 7c:fe:90:69:81:56 \
	dst_ip 11.11.11.11 \
	src_ip 11.11.11.12 \
	indev $ETH \
	action drop

$TC filter add dev $ETH protocol ip prio 30 parent ffff: \
	flower ip_proto 6 \
	indev $ETH \
	action skbedit mark 0x1234

$TC filter add dev $ETH protocol ip prio 10 parent ffff: \
	handle 0x1234 fw action pass

The code was tested and applied on top of commit 3ebeac1d ("Merge branch
'cxgb4-next'")

Changes from V2:
- patch 1/10 ("net/flower: Introduce hardware offload support")
  - Remove unused variable [Dave]
  - Don't fail command when HW can't offload filter [John]
- patch 3/10 ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef")
  - Mention in changelog that struct tc_action is now exposed out of the ifdef.
- patch 4/10 ("net/act_skbedit: Utility functions for mark action")
  - Document clearly that is_tcf_skbedit_mark() is returning true if and only
    if the only action is mark [Dave]
- patch 8/10 ("net/mlx5e: Introduce tc offload support")
  - make mlx5e_tc_add_flow() static

Changes from V1:
- patch 3/10 ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef")
  - fixed return value of tc_no_actions

Changes from V0:
- Use tc_no_actions and tc_for_each_action instead of ifdef CONFIG_NET_CLS_ACT
- Replace ENOTSUPP (and some EINVAL) with EOPNOTSUPP
- Name the flower command enum
- fl_hw_destroy_filter() to return void - nobody uses the return value
- mlx5e_tc_init() and mlx5e_tc_cleanup() to be called from the right places.
- When adding HW rule fails - fail the command
- Rules are added to be processed both by HW and SW unless SKIP_HW is given
- Adding patch 6/10 ("net/mlx5e: Relax ndo_setup_tc handle restriction")

Main changes from the RFC [1]:
- API
  - Using ndo_setup_tc() instead of switchdev
- act_skbedit, act_gact
  - Actions are not serialized to NIC driver, instead using access functions.
- cls_flower
  - prevent double classification by software by not adding
    successfuly offloaded filters to the hashtable
  - Fixed some bugs in original RFC with rule delete
- mlx5
  - Adding flow table to kernel namespace instead of a new namespace
  - s/offload/tc/ in many places
  - no need for a special kconfig since switchdev is not used
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce offloading of skbedit mark action.

For example, to mark with 0x1234, all TCP (ip_proto 6) packets arriving
to interface ens9:

 # tc qdisc add dev ens9 ingress
 # tc filter add dev ens9 protocol ip parent ffff: \
     flower ip_proto 6 \
     indev ens9 \
     action skbedit mark 0x1234
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse tc_cls_flower_offload into device specific commands and program
the hardware to classify and act accordingly.

For example, to drop ICMP (ip_proto 1) packets from specific smac, dmac,
src_ip, src_ip, arriving to interface ens9:

 # tc qdisc add dev ens9 ingress

 # tc filter add dev ens9 protocol ip parent ffff: \
     flower ip_proto 1 \
     dst_mac 7c:fe:90:69:81:62 src_mac 7c:fe:90:69:81:56 \
     dst_ip 11.11.11.11 src_ip 11.11.11.12 indev ens9 \
     action drop
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend ndo_setup_tc() to support ingress tc offloading. Will be used by
later patches to offload tc flower filter.

Feature is off by default and could be enabled by issuing:
 # ethtool  -K eth0 hw-tc-offload on

Offloads flow table is dynamically created when first filter is
added.
Rules are saved in a hash table that is maintained by the consumer (for
example - the flower offload in the next patch).
When last filter is removed and no filters exist in the hash table, the
offload flow table is destroyed.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the vlan and main flow tables to use priority 1. This will allow
the upcoming TC offload logic to use a higher priority (0) for the
offload steering table.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restricting handle to TC_H_ROOT breaks the old instantiation of mqprio
to setup a hardware qdisc. This patch relaxes the test, to only check the
type.

Fixes: 08fb1dac ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to handle flow table entry destinations only if the action
associated with the rule is forwarding (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST).

Fixes: 26a81453 ('net/mlx5_core: Introduce flow steering firmware commands')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable device drivers to query the action, if and only if is a mark
action and what value to use for marking.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce the macros tc_no_actions and tc_for_each_action to make code
clearer.
Extracted struct tc_action out of the ifdef to make calls to
is_tcf_gact_shot() and similar functions valid, even when it is a nop.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will be used in a following patch to query if a key is being used, and
what it's value in the target object.
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is based on a patch made by John Fastabend.
It adds support for offloading cls_flower.
when NETIF_F_HW_TC is on:
  flags = 0       => Rule will be processed twice - by hardware, and if
                     still relevant, by software.
  flags = SKIP_HW => Rull will be processed by software only

If hardware fail/not capabale to apply the rule, operation will NOT
fail. Filter will be processed by SW only.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Suggested-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

John Crispin says:

====================
net-next: mediatek: add ethernet driver

This series adds support for the Mediatek ethernet core found on current ARM
based SoCs. The driver works on MT2701 and MT7623 SoCs

Instead of trying to upstream everything at once I decided to concentrate on
the important parts required to make current generation silicon work. The V3
series only includes the code required to make dual MAC setups work and only
supports the newer QDMA engine.

Changes in V5
* reduce the mdio timeut to HZ
* add a call to usleep_range() which schedules in the background.

Changes in V4
* remove ugly _FE macro, use offsetof() instead

Changes in V3
* only include code for MT2701/7623 support
* drop support for PDMA and older MIPS based SoCs
* drop switch support

Changes in V2
* change the namespace of the functions from fe_* to mtk_*
* add support for the latest generation of ARM SoCs
* add dual MAC support
* remove the swconfig specific bits
* remove most of the magic values and replace them with defines
* add verbose descriptions to the patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myself and Felix as the Maintainers for the MediaTek ethernet driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Makefile and Kconfig required to make the driver build.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethernet support for MediaTek SoCs from the MT7623 family. These have
dual GMAC. Depending on the exact version, there might be a built-in
Gigabit switch (MT7530). The core does not have the typical DMA ring setup.
Instead there is a linked list that we add descriptors to. There is only
one linked list that both MACs use together. There is a special field
inside the TX descriptors called the VQID. This allows us to assign packets
to different internal queues. By using a separate id for each MAC we are
able to get deterministic results for BQL. Additionally we need to
provide the core with a block of scratch memory that is the same size as
the RX ring and data buffer. This is really needed to make the HW datapath
work. Although the driver does not support this yet, we still need to
assign the memory and tell the core about it for RX to work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>